Flexel TH132-AF Manual

FLEXEL
SUMMARY
• OPTIONS SELECTION
At the back of the thermostat, there are 2 selection switches to set at your
preferences.
• Temperature in °C or °F
• Early Start function.
• TO SET TIME AND DAY
Press on DAY, HOUR and MIN buttons to adjust time and day.
• TO RECORD THE (COMFORT) SETPOINT TEMPERATURE
Select chosen setpoint temperature by using
button (2 to 3 seconds) until
• TO RECORD THE (ECONOMY) SETPOINT TEMPERATURE
Select chosen setpoint temperature by using
button (2 to 3 seconds) until
• TO RECORD THE (VACATION) SETPOINT TEMPERATURE
Select chosen setpoint temperature by using
button (2 to 3 seconds) until
• OPERATING MODES
To select an operating mode, use Mode/Return button.
AUTO : Runs the programs.
can override temporarily your programming up to the next pro-
gram.
MAN : Maintains the selected temperature.
perature setting.
Setting temperature
To set
the day
To set
the hour
To set the
minutes
To set the
program
To erase a
program
To select the
operating mode
or to exit the
Programming
mode
Heating
Operating
indicator *
modes
* Percentage (%) of energy sent to the heating system to maintain the
desired temperature.
0 - 20% 20 - 40%
TH132-AF (230 VAC)
or button. Press on
icon appears on display.
or button. Press on
icon appears on display.
or button. Press on
icon appears on display.
or shows temperature setting and
or changes the tem-
Time and day
of the week
Comfort
Economy
Vacation
To limit the floor
temperature
Up and down
to adjust the
temperature
setting
Comfort, Economy and
Program
Vacation temperature
number
settings
40 - 60% 60 - 80% 80 - 100%
DIGITAL THERMOSTAT TH132-AF (230 VAC)

INSTALLATION

This thermostat is designed to use a floor-heating sensor to regulate room
temperature.
The TH132-AF has two temperature sensors. The first one, installed in the
box, controls the ambient temperature. The second one, installed in the
floor, limits the floor temperature. Electricians or experienced technicians
should install the thermostat.
This thermostat should be connected on a circuit equipped with a fuse or a
circuit breaker. It must be installed on a certified electrical box.
For a new installation, choose a location about 1.5 meters above the floor,
with good air circulation. The thermostat must be installed on an inside wall.
Avoid locations where there are air drafts (top of a staircase, air outlet), dead
air spots (behind a door), direct sunlight or concealed chimneys or stove
pipes.
TURN OFF POWER TO THE HEATING SYSTEM AT THE MAIN POWER
PANEL TO AVOID ELECTRICAL SHOCK. Keep air vents of the thermostat
clean and free from obstructions.
PARTS INCLUDED
- One (1) TH132-AF (230 VAC) thermostat
- One (1) temperature sensor with a 3 meter extension
- One (1) wall plate (in certain countries)
1. Installation of thermostat
Turn off power to the heating system at the main power panel to avoid elec-
trical shock.
Unscrew and remove the front part of the thermostat
from the base.
Please take note that the screw cannot be completely
retracted.
If your thermostat is equipped with a wall plate
Before making the connections, make sure that the
base covers the electrical box entirely. If not, insert
the wall plate on rear of the base. (The wall plate can
be used to cover the plate for aesthetics.)
Connect the wires (see section 1.1).
Connect the sensor (see section 1.2).
Secure the base to the electrical box anchorage.
(The head of the screw must be less than 2mm of
thickness.)
Set the switches located at the back of the front part
of the thermostat before replacing it in the base.
(see section 1.3)
Affix the front part of the thermostat to the base
using the enclosed screw.
You can now turn the power back on.
400-132-019-A
TH132-AF
16/12/04 1/3