Oregon Scientific Alize BAR266 User Manual

1. LED status indicator
2. Wall mount hole
3. Battery compartment
4. RESEt hole
5. chANNEL switch
NOtE The sensor included in this package can search
channels 1, 2 and 3. To search all 5 channels, you may
purchase additional sensors. Visit www.oregonscientific.com
for more about accessory sensors.
Alizé Weather Station (Standard Version)
GEttiNG StARtED
Model: BAR266
iNSERt BAttERiES
User Manual
1. Gently pull the battery compartment cover apart from the
unit.
2. Insert the batteries, matching the polarities (+/-).
EN
cES AMONG thN129h
3. Press RESEt after each battery replacement.
OVERViEW
FRONt ViEW
1
2
NOtE Replace the batteries when
3 the display/backlight is dim.
4
REMOtE SENSOR
5 The main unit can collect data from up to 5 sensors.
To set up the sensor:
1. Open the battery compartment.
1. Ice alert indicator
2. Insert the batteries, matching the polarities (+/-).
2. + - Press to increase settings, press and hold to increase
3. Select a channel then press RESEt.
settings rapidly
4. Close the battery door.
3. - Press to toggle between the clock and calendar, press
5. Place the sensor within 30 m (98 ft) of the main unit using
and hold to enter the setting mode
the table stand or wall mount.
4. MEM – Press to toggle the current/maximum/minimum
indoor/outdoor temperature and indoor humidity records,
tiP
Ideal placements for the sensor would be in any location on
press and hold to clear the MAX/MIN records
the exterior of the home at a height of not more than 1.5m (5ft)
5. – - Press to decrease settings, press and hold to decrease
and which can shield it from direct sunlight or wet conditions
settings rapidly. Press and hold to turn off the ice alert
for an accurate reading.
tOP ViEW
1 2 3 4 5
1. SENSOR – Press to toggle between indoor sensor and
channel 1-5, turn on or off auto-loop. Press and hold to
search for the sensor for all channels
LiGht
2. – Press to turn on the backlight
3. Rcc – Press to turn on and toggle EU/UK/US RCC
NOtE Use alkaline batteries for longer usage and consumer
function, press and hold to turn off RCC function
grade lithium batteries in temperatures below freezing.
4. °c/°F - Press to toggle the desired temperature unit
5. RESEt – Press to reset all settings to default
SENSOR DAtA tRANSMiSSiON
to search for a sensor:
tOP ViEW
Press and hold
The sensor reception icon in the remote sensor area shows
the status:
icON
1 2
1. Battery compartment
2. Battery compartment cover
tiP The transmission range may vary depending on many
factors. You may need to experiment with various locations
to get the best results.
LcD DiSPLAY ScREEN
cLOcK
1 2 3 4 5 6 7
cLOcK REcEPtiON
8
This clock is designed to synchronize its clock automatically
with a clock signal. Press
9
region (EU/UK/US).
10
11 Region
EU
12
UK
US
Clock signal reception indicator:
17 16 15 14 13
icons
1. Weather forecast display
2. RCC Clock reception signal indicator
3. MAX/MiN temperature indicator
4. Outdoor sensor low battery display
5. Remote sensor reception indicator
6. Temperature auto-loop indicator (flash)
7. Outdoor sensor channel number
8. Main unit low battery display
9. Indoor/outdoor temperature
10. Temperature trend indicator
11. Indoor/outdoor temperature unit display (°c/°F) NOtE It takes 2-10 minutes to receive the clock signal. If
the signal is weak, it could take up to 24 hours to receive a
12. Humidity trend indicator
13. Humidity reading display valid signal.
14. Date/month format display (date: month/month: date)
15. Time/Calendar
You may turn off the clock signal reception and set the clock
16. AM/PM
manually.
17. Weekday display
to disable signal reception:
Press and hold
REMOtE SENSOR (thN132N)
NOtE The signal reception is on after each reset or battery
2
replacement.
1
SEt thE cLOcK MANUALLY
4
1. Press and hold
3
5 2. Press and hold
number flashes.
3. Press once or press and hold +/- to adjust the setting. For
EU/UK, the time-zone offset sets the clock up to +/- 23 hours
from the received clock signal time. For US, the time-zone
setting is 0(P), 1(M), 2(C), 3(E).
4. Press
5. Press once or press and hold + / - to adjust the setting for
12/24h hour format, hour, minute, year, calendar format
(month-day/day-month), month, date and language.
P/N: 300103772-00001-10 REV1.0
2／3
6. Press to confirm each setting.
NOtE The language options are English (ENG), Spanish
SPA itA
( ), Italian ( ), French (
When the unit is in idle mode, you may choose the display
mode options.
To select the display mode:
Press to select between clock and date display.
WEAthER FOREcASt
This product forecasts the next 6 hours of weather within a
19-31 mile (30-50 km) radius.
Screen display
LOcAtiON MEANiNG
Sensor batteries are low
Main unit batteries are low
displays , or when
tEMPERAtURE AND hUMiDitY
to toggle temperature unit:
Press °c / °F inside the battery compartment.
NOtE When the indoor temperature is lower than -5 °C (23.0 °F),
the screen displays LL.L. When the temperature is higher than
50 °C (122.0 °F), the screen displays
to toggle sensor display:
Press .
to auto-loop between sensors:
Press repeatedly until the unit displays
on each sensor displays for 3 seconds. Press
turn off the auto-loop, the
1.5 m (5 ft)
NOtE
The sensor displays in ascending order. If not all
5 sensors are present, the main unit skips the absent sensor
and advances to the next present sensor.
to toggle MAX/MiN
unit and the selected sensors:
Press MEM repeatedly.
.
to clear the MAX/MiN records:
Press and hold MEM
temperature and indoor humidity will be cleared and starts to
Doscription
record the current readings.
Searching for sensor(s).
Sensor is found.
icE WARNiNG
Cannot find sensors.
If the channel 1 sensor temperature falls between 3 °C to -2 °C
(37 °F to 28 °F), LED indicator will flash, and will stop flashing
once the temperature is out of this range. Press and hold - to
turn off the ice warning alert.
NOtE The ice warning alert turns on again when the
temperature falls into the temperature range.
BAcKLiGht
Press to turn on the backlight. The backlight will be on
for 5 seconds.
to turn on and select the desired
Signal
PREcAUtiONS
DCF
• Do not subject the unit to excessive force, shock, dust,
MSF temperature or humidity.
• Do not immerse the unit in water. If you spill liquid over it,
WWVB
dry it immediately with a soft, lint-free cloth.
• Do not clean the unit with abrasive or corrosive materials.
• Do not tamper with the unit's internal components. This
invalidates the warranty.
Description
• Only use fresh batteries. Do not mix new and old batteries.
M a i n u n i t i s
• Images shown in this manual may differ from the actual
searching for
display.
c l o c k s i g n a l
• When disposing of this product, ensure it is collected
strength
separately for special treatment.
M a i n u n i t i s
• Placement of this product on certain types of wood may
searching for
result in damage to its finish for which Oregon Scientific will
clock signal
not be responsible. Consult the furniture manufacturer's care
instructions for information.
No clock signal
• The contents of this manual may not be reproduced without
the permission of the manufacturer.
• Do not dispose old batteries as unsorted municipal waste.
Collection of such waste separately for special treatment is
necessary.
• Please note that some units are equipped with a battery
safety strip. Remove the strip from the battery compartment
before first use.
NOtE
The technical specifications for this product and the
contents of the user manual are subject to change without
. The icon turns off.
notice.
SPEciFicAtiONS
MAiN UNit
L x W x H
to disable signal reception.
. The screen displays ZONE and the
Weight
Temperature range
Resolution
Accuracy
to confirm.
Power
REMOtE UNit (thN132N)
L x W x H
FRE GER
) and German ( ).
Weight
Transmission range
Temperature range
Relative humidity
measurement
Humidity accuracy
Signal frequency
Power
Description
Sunny
ABOUt OREGON SciENtiFic
Visit our website www.oregonscientific.com to learn more about
Oregon Scientific products.
Cloudy
For any enquiry, please contact our Customer Services at
info@oregonscientific.com.
Rainy
Oregon Scientific Global Distribution Limited reserves the right
to interpret and construe any contents, terms and provisions
Snowy
in this user manual and to amend it, at its sole discretion, at
any time without prior notice. To the extent that there is any
inconsistency between the English version and any other
language versions, the English version shall prevail.
Fcc StAtEMENt
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must
accept any interference received, including interference that
may cause undesired operation.
hh.h .
WARNiNG Changes or modifications not expressly approved
by the party responsible for compliance could void the user's
authority to operate the equipment.
NOtE
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
. The data
residential installation.This equipment generates, uses and
again
can radiate radio frequency energy and, if not installed and
icon turns off.
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
and current records between the main
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
. All MAX/MIN data of indoor and outdoor
for help.
This Class B digital apparatus complies with Canadian
ICES- 3(B)/NMB-3(B)
cLOcK REcEPtiON
The following information is not to be used as contact for
support or sales. Please call our customer service number
(listed on our website at www.oregonscientific.com. or on the
warranty card for this product) for all inquiries instead.
We,
Name: Oregon Scientific, Inc.
Address: 10778 SW Manhasset Dr.
Tualatin, Or 97062 USA
Telephone No.: 1-800-853-8883
declare that the product
Product No.: BAR266
Product Name: Alizé Weather Station
(Standard Version)
Manufacturer: IDT Technology Limited
Address: Block C, 9/F, Kaiser Estate,
Phase 1, 41 Man Yue St.,
Hung Hom, Kowloon,
Hong Kong
EU-DEcLARAtiON OF cONFORMitY
Hereby, Oregon Scientific, declares that this Alizé Weather
Station (Standard Version) (model: BAR266) is in compliance
with the essential requirements and other relevant provisions
of Directive 1999/5/EC. A copy of the signed and dated
Declaration of Conformity is available on request via our
Oregon Scientific Customer Service.
cOUNtRiES RttE APPROVED cOMPLiED
All EU countries, Switzeriand ch
156 x 82 x 19 mm
(6.1 x 3.2 x 0.7 in)
158 g (5.6 oz)
-5°C to 50°C (23°F to 122°F)
0.1°C (0.2°F)
0°C-40°C: ±1°C (± 2.0°F)
40°C <T<0°C: ±2°C (± 4.0°F)
2 x UM-4 (AAA) 1.5 V
batteries
96 x 50 x 22 mm
(3.78 x 1.97 x 0.87 in)
50 g (1.76 oz) without
batteries
30 m (98 ft) unobstructed
-20 °C to 60 °C
(-4 °F to 140 °F)
Estación Meteorológica Alizé
25% RH - 95% RH
(Versión Estándar)
±8% (20%~90%)
433 MHz Modelo: BAR266
1 x UM-3 (AA) 1.5 V
Manual de usuario
batteries
ES
cES AMONG thN129h
DEScRiPciÓN GENERAL
ViStA FRONtAL
1
1. Indicador de alerta de helada
2. + - Pulse este botón para incrementar los valores de los
parámetros, o manténgalo pulsado para incrementarlos con
más rapidez.
3. - Pulse este botón para mostrar el reloj o el calendario
y manténgalo pulsado para acceder al modo de ajustes.
4. MEM – Pulse este botón para alternar entre la temperatura
actual/máxima/mínima interna y externa, y los registros
de humedad interna. Manténgalo pulsado para borrar los
registros máximos y mínimos.
5. – - Pulse este botón para reducir los valores de los
parámetros, o manténgalo pulsado para reducirlos con más
rapidez. Manténgalo pulsado para desactivar la alerta de
helada.
ViStA SUPERiOR
1 2
1. SENSOR – Pulse este botón para seleccionar el sensor
interno o uno de los canales del 1 al 5, o bien para activar/
desactivar el modo de escaneo automático. Manténgalo
pulsado para buscar el sensor de cada uno de los canales.
2. LiGht – Pulse este botón para activar la luz de fondo.
3. Rcc – Pulse este botón para seleccionar la función RCC
para EU, UK o US. Manténgalo pulsado para desactivar la
función RCC.
4. °c/°F - Pulse este botón para seleccionar la unidad de
temperatura deseada.
5. RESEt – Pulse este botón para resetear todos los ajustes
a los valores predeterminados de fábrica.
ViStA tRASERA
1
1. Compartimento de las pilas
2. Tapa del compartimento de las pilas
PANtALLA LcD
1 2 3 4 5 6 7
17 16 15 14 13
1. Pronóstico meteorológico
2. Indicador de la recepción de la señal horaria RCC
3. Indicador de temperatura MAX/MiN
4. Icono de pilas bajas del sensor externo
5. Icono de la recepción de la señal del sensor externo
6. Indicador de escaneo automático de la temperatura
7. Número de canal de sensor externo
8. Icono de pilas bajas de la unidad principal
9. Temperatura interna y externa
10. Indicador de la tendencia de la temperatura
11. Icono de la unidad de temperatura interna/externa (°c/°F)
12. Indicador de la tendencia de la humedad
and Norway N
13. Lectura de la humedad
v
14. Indicador del formato del día del mes/mes (día del mes :
mes; mes : día del mes)
15. Hora/fecha
16. AM/PM
17. Día de la semana
SENSOR REMOtO (thN132N)
2
1
3
1. Indicador LED de estado
2. Agujero para instalación en pared
3. Compartimento de las pilas
4. Agujero de reseteo (RESEt)
5. Selector de canal (chANNEL)
NOtA El sensor incluido con la unidad puede buscar los
canales 1, 2 y 3. Vd. puede comprar sensores adicionales
para buscar los 5 canales. Visite www.oregonscientific.com
para más información acerca de los sensores accesorios.
2
GUÍA DE iNiciO
3
iNStALAciÓN DE LAS PiLAS
4
1. Abra la tapa del compartimento de las pilas con cuidado.
2. Inserte las pilas haciendo coincidir las polaridades (+/-).
5
3. Pulse RESEt cada vez que cambie las pilas. La unidad se
enciende automáticamente.
UBicAciÓN SiGNiFicADO
Las pilas del sensor están
bajas
Las pilas de la unidad
principal están bajas
NOtA Reemplace las pilas cuando aparezca o cuando
la pantalla / retroiluminación se atenúe.
SENSOR REMOtO
La unidad principal puede recoger datos de hasta 5 sensores.
cómo instalar un sensor:
1. Abra el compartimento de las pilas.
2. Inserte las pilas haciendo coincidir el sentido de la
3 4 5
polaridad (+/-).
3. Seleccione un canal y pulse RESEt.
4. Cierre la tapa del compartimento de las pilas.
5. Coloque el sensor a 30 m (98 pies) de la unidad principal
utilizando la pata de apoyo o montándolo en la pared.
cONSEJO Para obtener una lectura precisa, procure colocar
el sensor en un lugar al aire libre a una altura igual 1,5 m
(5 pies) y donde esté protegido de la luz directa del sol o
la lluvia.
1.5 m (5 ft)
NOtA Utilice pilas alcalinas para un uso más prologando, o
pilas de litio para temperaturas bajo cero.
tRANSMiSiÓN DE LOS DAtOS DEL SENSOR
Para buscar un sensor:
2
Mantenga pulsado .
El icono de recepción de la señal del sensor remoto mostrará
su estado:
icono Descripción
Buscando sensor(es).
Se ha encontrado el
sensor.
8
N o p u e d e e n c o n t r a r
9
sensores.
10
11
cONSEJO
12 El alcance de la transmisión puede variar en
función de muchos factores. Pruebe a colocar el sensor
en varios lugares hasta que obtenga unos resultados
satisfactorios.
RELOJ
REcEPciÓN DE LA hORA
Este reloj está diseñado para sincronizar la hora con la señal
horaria automáticamente. Pulse para activar la función
y seleccionar una región (EU/UK/US).
Región Señal
EU DCF
UK MSF
US WWVB
Indicador de recepción de la señal horaria:
iconos Descripción
La unidad princi
pal está detectando
la intensidad de la
señal horaria
La unidad principal
está buscando una
(parpadeando)
señal horaria
No se ha encontrado
una señal horaria
NOtA La recepción de la señal puede tardar de 2 a 10 minutos
en establecerse. Si la señal es débil, puede tardar hasta 24 horas
en recibir una señal válida.
4
5