PresencePLUS Pro is an easy-to-use camera system with advanced visual inspection capabilities. With limited knowledge of vision systems, a user can quickly and accurately set up PresencePLUS Pro for an inspection that evaluates product on a production line. Inspection parameters are set up using a remote personal computer (PC).
• Additional connections (Pin 4 - Pin 20) sensor, or a device with a step 3 step 3 Lighting similar output. Install the dedicated light source, according to the instructions included with the light source. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 page...
Page 4
Protocols tab 192.168.0.2 and subnet mask to 255.255.255.0 2. Install the PresencePLUS Pro software a. Insert the Installation CD b. Click Install PresencePLUS Pro PC Software Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 page...
1. Start the PresencePLUS Pro program by clicking Start > Program Files > PresencePLUS Pro. 2. At start-up, PresencePLUS Pro will try to communicate with the camera. • If communication with the camera is successful, the application will launch and display the Setup or Run screen.
7 step 7 Software Setup Use the Main Menu toolbar to navigate the PresencePLUS Pro options. Proceeding from left to right, the buttons in the Menu toolbar step through the process of creating an inspection file. Inspection Work Flow Set up the camera, lens, and lighting, to acquire a reference image.
Before entering Run, save the inspection file to one of the • Save a backup 12 memory locations on the controller. copy of your inspection to the host PC. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 page...
Product the ROI category Change input to initiate an inspection change. Passing Tool Failing Tool To begin inspecting, click the Start button in the Run screen. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 page...
Input/Output Configuration Tab Save inspections on the controller or PC. Provides help files and PDFs of the Installation Manual (p/n 68368) and the full-length Operator’s Guide (p/n 68367). Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 page...
Maintenance Maintenance tasks include keeping the hardware free of dust and dirt and updating the PresencePLUS Pro software as new versions become available. Cleaning the Camera and Controller Regularly remove any accumulated dust or dirt from the camera and controller using a soft cloth. If needed, slightly dampen the cloth with a weak solution of neutral detergent.
2. Check the cable for breaks, power down, then power up. • Indicator lights on controller’s RJ-45 3. Replace the cable. port are OFF. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 page...
Page 12
NPN Hookup PNP Hookup Output Rating – 10-30V dc 10-30V dc – Load Load PresencePLUS Pro 1 RJ-45 Ethernet port for running software Communication PresencePLUS Pro 1 RS232 port for running software Memory Stores up to 12 inspection files Voltage: 10-30V dc Power Current: 1.5 amps max.
Page 13
4.8 x 3.6 mm, 6 mm diagonal (1/3" CCD) Imager Pixel Size: 7.4 x 7.4 microns Interface LVDS Max. Cable 7 m (23') Length Exposure Time 0.01 ms to 3600 ms Lens Mount C-mount Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 page...