Advertisement
OPERATOR'S MANUAL
A Division of Snow Joe
, LLC
®
THANKS
OF A REMANUFACTURED PRODUCT.
To make sure you get the most out of
your product, be sure to register online at
to enjoy full product support.
R
ELECTRIC WOOD CHIPPER + SHREDDER
14-AMP | 16:1 REDUCTION RATIO
Model CJ601E-RM
FOR
snowjoe.com
PASTE UPC LABEL HERE
YOUR
Form No. SJ-CJ601E-RM-880E-V1
PURCHASE
Advertisement
Table of Contents
Summary of Contents for sunjoe CJ601E-RM
- Page 1 14-AMP | 16:1 REDUCTION RATIO OPERATOR’S MANUAL Model CJ601E-RM A Division of Snow Joe , LLC ® Form No. SJ-CJ601E-RM-880E-V1 THANKS YOUR PURCHASE OF A REMANUFACTURED PRODUCT. To make sure you get the most out of your product, be sure to register online at snowjoe.com...
-
Page 2: General Safety Warnings
OPERATOR’S MANUAL Model CJ601E-RM A Division of Snow Joe , LLC ® Form No. SJ-CJ601E-RM-880E-V1 IMPORTANT! General Safety Safety Instructions 1. Avoid dangerous environments – Do not use the wood chipper + shredder in rain or in damp or wet locations. Do... -
Page 3: Personal Safety
WARNING! operation. A part that is damaged should be properly Never reach into the hopper until the repaired or replaced. Contact the Snow Joe + Sun Joe ® ® wood chipper + shredder has come to a complete stop and customer service center at 1-866-SNOWJOE is unplugged. - Page 4 Table 1. Method of Securing Extension Cord WARNING! Cord set Appliance cord Electric shock may cause SEVERE INJURY or DEATH. Heed these warnings: • Do not allow any part of the wood chipper + shredder to make contact with water while it is in operation. If the appliance becomes wet while turned off, wipe dry (A) Tie cord as shown before starting.
-
Page 5: Double-Insulated Appliances
Double-Insulated Appliances In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double- insulated appliance requires extreme care and knowledge of the system, and should be performed only by qualified service personnel at an authorized Snow Joe + Sun Joe... -
Page 6: Safety Symbols
Safety Symbols The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbols Descriptions Symbols Descriptions READ THE OPERATOR'S MANUAL(S) – Read, understand, SAFETY ALERT –... -
Page 7: Technical Data
Know Your Electric Wood Chipper + Shredder Read the owner’s manual and safety instructions carefully before operating the electric wood chipper + shredder. Compare the illustration below to the electric wood chipper + shredder in order to become familiar with the location of the various controls and adjustments. - Page 8 Unpacking 2. Insert the wheel axle into the shredder stand assembly, and re-assemble the shaft sleeve and the support cover (Fig. 2). Carton Contents • Electric wood chipper + shredder main body with hopper Fig. 2 • Electric wood chipper + shredder stand assembly Shaft sleeve Wheel axle •...
-
Page 9: Operation
Fitting the Paddle Holder and the Paddle Wheel Fig. 5 1. Stand the unit up, and clip the paddle holder to the standing assembly (Fig. 8). Fig. 8 Standing assembly Wheel cover 6. Repeat the steps 2 – 4 to assemble the other wheel. Paddle holder Stand Assembly Fitting 1. - Page 10 3. To power the wood chipper + shredder off, push the Fig. 10 removable safety switch to the OFF position. To disable the machine, remove the safety switch completely Hopper (Fig. 13). locking knob Fig. 13 Removable 1. Make sure the removable safety switch is in the OFF safety switch position.
-
Page 11: Overload Protection
Overload Protection 2. Use the paddle to push the material inside the hopper if needed (Fig. 15). Your electric wood chipper + shredder is designed with overload protection. If the shredder is clogged during Fig. 15 shredding, the overload protection will cut the power automatically to protect your shredder. -
Page 12: Cutting Blade Replacement
1. Stop the motor and disconnect the unit from the power Fig. 17 supply. 2. Unscrew the hopper locking knob counterclockwise to open the hopper (Fig. 17). 3. Align the cutting head past the splash guard so that the blade bolts can be removed; secure the cutting head Hopper from rotating by inserting a rod (e.g. -
Page 13: Service & Support
Storage Follow the steps below to prepare the electric wood chipper + shredder for storage: 1. Disconnect the power supply to the wood chipper + shredder. 2. Clean the wood chipper + shredder with a damp cloth or hand brush. 3. -
Page 14: Troubleshooting
Troubleshooting Possible Cause Problem Remedy Motor does not run • Power failure/unit not plugged into a • Check to make sure unit is plugged into a working receptacle. working outlet. Make sure extension cord is not damaged. • The overload protection has responded. - Page 15 Optional Accessories WARNING! ALWAYS use only authorized Snow Joe + Sun Joe replacement parts and accessories. NEVER use ® ® replacement parts or accessories that are not intended for use with this tool. Contact Snow Joe + Sun Joe if you are unsure ®...
- Page 16 SNOW JOE + SUN JOE REFURBISHED GOODS WARRANTY ® ® GENERAL CONDITIONS: Snow Joe + Sun Joe may from time to time change the design ® ® of its products. Nothing contained in this warranty shall be Snow Joe + Sun Joe operating under Snow Joe , LLC warrants ®...
- Page 17 snowjoe.com WARNING! This product or its power cord contains chemicals, including lead, known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. For more information go to www.P65Warnings.ca.gov. WARNING! Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known [to the State of California] to cause cancer, birth defects, or other reproductive harm.