Table of Contents
Advertisement
Quick Links
RANDOM ORBITAL POLISHER
Features:
Random orbit polishing ac on for swirl-free nish
Includes mul -posi on side handle and D-handle for comfort
Variable speed se ngs allows the correct amount of polishing power for each applica on
So start feature provides improved speed control
Rubber grip provides added comfort and reduces vibra on
6" hook and loop backing pad makes changing pads fast and easy
Accepts 5/16"x24 spindle thread accessories
6A, 120V AC, 60 HZ
No load speed: 2500-6500 OPM
WARNING: This product may contain chemicals, including lead, known to the State of California
ATD-10506
OWNER'S MANUAL
* Shown with both handles included
to cause cancer, birth defects or other reproductive harm. Wash hands after handling.
Made in China to ATD Tools, Inc. Specifications
Visit us at www.atdtools.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ATD Tools ATD-10506
Summary of Contents for ATD Tools ATD-10506
- Page 1 No load speed: 2500-6500 OPM WARNING: This product may contain chemicals, including lead, known to the State of California to cause cancer, birth defects or other reproductive harm. Wash hands after handling. Made in China to ATD Tools, Inc. Specifications Visit us at www.atdtools.com...
- Page 2 General Safety Warnings: WARNING: The instruc ons and warnings contained in this manual should be read and understood before using or opera ng this tool. Do not allow anyone to use or operate this tool un l they have read this manual and have developed a thorough understanding of how this tool works. Failure to observe any of the following instruc ons could result in severe personal injury to tool user and bystanders, or cause damage to the tool and property.
- Page 3 Electrical Safety Warnings: WARNING: Read all safety warnings and instruc ons. Failure to follow all warnings and instruc ons may result in electric shock, re and/or serious injury or death. WARNING: Before conne ng a tool to a power supply, always check to ensure the power supply corresponds to the voltage on the nameplate of the tool.
-
Page 4: Power Tool Use And Care
WARNING: Avoid body contact with electrically grounded surfaces. There is an increased risk of electric shock if your body is grounded. WARNING: If the work area is not equipped with a permanently installed Ground Fault Circuit Interrupter outlet (GFCI), use a plug-in GFCI between the power tool or extension cord and the power receptacle. - Page 5 WARNING: Do not force the power tool. Use the correct power tool for your applica on. The correct power tool will do the job be er and safer at the rate for which it was designed. WARNING: Do not use the power tool if the switch loses its func on. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
- Page 6 Operating Instructions Setup - Before Use: Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this power tool. WARNING: TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Make sure that the Power Switch is in the off-position and unplug the tool from its electrical outlet before performing any procedure in this section.
-
Page 7: Tool Set Up
ASSEMBLY Installing the “D” Shaped Handle WARNING: TO PREVENT SERIOUS INJURY: Do not operate this tool with one hand only or without the one of the two handles properly installed. 1. The “D” Shaped Handle may be installed in place 2. - Page 8 NOTICE: Only use slower speeds for polishing. Otherwise, damage may occur to the paint Note: The most common error when waxing/polishing being polished. ATD Tools, Inc. is not a vehicle is applying too much wax. If the foam responsible for damage to the vehicle’s pad becomes saturated with wax, applying wax will finish due to improper use of this tool.
-
Page 9: Maintenance And Servicing
Sanding Instructions WARNING: TO PREVENT SERIOUS INJURY: Grip the tool firmly in both hands. 1. Wipe the work surface clean of all dirt and debris, 6. Keep heavy pressure off of the tool when operating. especially that of previous Allow the tool to do the work. coarser sanding sessions, which will scratch 7. -
Page 10: Troubleshooting
Troubleshooting Problem Possible Causes Likely Solutions Tool will not start. 1. Cord not connected. 1. Check that cord is plugged in. 2. No power at outlet. 2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads. - Page 11 ATD-10506 ITEM# ORDERING PART# PART DESCRIPTION ITEM# ORDERING PART# PART DESCRIPTION PRT10506 01 BACKING PAD PRT10506 25 ROTOR PRT10506 02 SCREW M X12 PRT10506 26 FAN SHROUD PRT10506 03 COUNTER WEIGHT PRT10506 27 STATOR PRT10506 0 SPINDLE 01 PRT10506 28...
-
Page 12: Year Limited Warranty
WARRANTY 1 YEAR LIMITED WARRANTY THIS WARRANTY AND CONFIRMED RECEIPT(S) SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMES _______________________________________ PURCHASED FROM: DATE PURCHASED: ____________________________________________ INVOICE/RECIEPT NUMBER: _________________________________________ ATD product if it was purchased new and the product has failed due to a defect in material or workmanship which you experienced during normal use of the product.
Need help?
Do you have a question about the ATD-10506 and is the answer not in the manual?
Questions and answers