Table of Contents
Advertisement
Quick Links
Rectangle vinyl gazebo
REQUIRED TOOLS
(not provided)
Cordless or electric screw gun(s)
Step ladders
Level
12' 4x4 post or two 2x4s for
propping roof sections
11" vise clamps and/or
C-clamps
Hammer
Utility knife
Measuring tape
Prybar
Pencil or pen
7/16" socket or wrench
3/4" drill bit
HARDWARE FOR ASSEMBLY
(provided)
2 1/2" screws Use to:
• Fasten joist together
• Fasten posts to outside joist
• Fasten rafter headers
• Fasten roof sections to top railing
2" screws Use to
• Screw down remaining deck boards
• Fasten rafters together
• Fasten railings to posts
• Fasten skirt board trim
NOTE: Caution See note 1 on page 8
1/4" x 6" lags with washers - Use to
• Fasten posts to outside joist
KIT ASSEMBLY INSTRUCTIONS
We have designed these instructions as a stepby
step procedure to simplify the assembly process.
Nevertheless, we do recommend including someone
with carpentry expertise on your crew.
BEFORE YOU START
Please read the entire set of instructions before you
start to assemble your gazebo. Also, make sure that
your site has been properly prepared and leveled.
TABLE OF CONTENTS
CUPOLA
Section 5 INSTALLING OPTIONAL SCREENING & DOOR
Step 12 Installing screen panels p7
Rectangle gazebo kit unwrapped
CAUTION Be sure you have enough help before
starting to unpack your kit because some sections
are heavy. Take extra care to prevent gazebo parts
or sections from falling.
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Gazebo Creations Vinyl
- Page 1 BEFORE YOU START Please read the entire set of instructions before you start to assemble your gazebo. Also, make sure that your site has been properly prepared and leveled. Rectangle vinyl gazebo TABLE OF CONTENTS Section 1 ASSEMBLING GAZEBO FLOOR REQUIRED TOOLS...
- Page 2 ASSEMBLING GAZEBO FLOOR Section step Laying out floor sections Arrange the floor sections in place, as they are numbered (Figure 1a). (You’ll find the numbers towards the center, on top of the joist.) Before assembling, be sure to place Figure 1c the door opening(s) correctly.
- Page 3 Inserting posts in pockets Figure 2a Insert posts into pockets until vinyl sleeves rest on the floor—keeping doorway positions in mind (Figure 2a). Be sure that the top of the posts are level with the top of the vinyl sleeves.
- Page 4 step Fastening skirt boards With all the railings fastened in place, drive 2 1/2" screws from the outside skirt board into the posts, two on each side, four per post (Figures 2g and 2h). To insure that the screen door will fit properly, adjust each post at the doorway opening at the bottom (if possible) so that it measures the same as the top.
- Page 5 step Installing roof sections Using one or more posts of the right height—either a 4x4 or two 2x4s screwed together—carefully brace up the roof panel at the center (Figure 3b). Temporarily fasten the post(s) to the roof panel and the floor so the brace can’t be pushed out.
- Page 6 step Fastening rafter plates & ceiling ties Finish fastening top rails to the rafter plate, one 2 1/2" screw at the inside of every other spindle (Figures 3g and 3h). Be sure to measure and adjust the posts in or out before clamping and Figure 3g fastening so the overhang...
- Page 7 INSTALLING OPTIONAL SCREENING & D O O R S e c t i o n step Installing screen door With the help of another person, carefully set the door in place. Using three painted 2" screws, Figure 5a drive the screws into the upper rail section (Figure 5a).
- Page 8 N o t e : 1 ) E x c e p t i o n : I f y o u o r d e r d e s i g n p o s t o n y o u r v i n y l g a z e b o y o u w i l l n e e d t o u s e 2 1 / 2 ”...
Need help?
Do you have a question about the Vinyl and is the answer not in the manual?
Questions and answers