Advertisement
Quick Links
DUAL ELECTRIC AIR COMMAND
I
NSTALLATION INSTRUCTIONS
Congratulations on your purchase of a new Firestone Air
Control Accessory Kit. This kit was designed to provide
inflation control of your Firestone air helper springs. This kit
will be an asset to your vehicle, meeting most all of your air
supply needs.
Please take a few minutes to read through the instructions,
identify the components, and learn how to properly install your
Air Control Accessory Kit.
N
:
OTE
The Air Control Accessory kit can be used with all
Firestone air helper springs products. If you are installing a
Firestone suspension system do not install the air line tubing
into the air springs as stated in the suspension system instruc-
tion manual. If you are adding the Air Control Accessory kit
to an existing Firestone suspension system you will need to
deflate the air springs and remove the air line tubing.
P
ARTS LIST
DUAL AIR CONTROL PANEL
COMPRESSOR
COMPRESSOR BRACKET
30 FT. AIR LINE TUBING
15 FT. 18 GAGE WIRE
10/32" X 1" MACHINE SCREW
10/32" LOCK NUT
1/4" X 1" HEX BOLT
1/4" HEX NUT
1/4" LOCK WASHER
24-8143
A
C
IR
ONTROL
1
1
1
1
1
2
2
2
2
2
03-01
30
200
psi
0
A
CCESSORY
N
C
OTE ON
ONNECTING THE AIR LINE TUBING
Cut the air line tubing as squarely as possible. To
connect the air line tubing to the fittings push the tubing
into the fittings as far as possible. If for any reason the
tubing must be removed the collar of the fitting can be
pushed toward the body of the fitting and the tubing can
be removed. Make sure the air helper springs are de-
flated. To reassemble make sure the tubing is cut squarely
and push back into the fitting.
T
:
OOLS REQUIRED
• 3/16" drill bit
• 1/4" drill bit
• Electrical pliers
• Phillips screw driver
• (2) 7/16" wrenches
1/8" NPT STRAIGHT FITTING
FUSE HOLDER
20 AMP. FUSE
FEMALE SPADE CONNECTOR
MALE SPADE CONNECTOR
WIRE CONNECTOR
RING TERMINAL
FOAM PAD
#10 FLAT WASHER
NYLON TIES
60
90
600
400
120
800
1000
kPa
PSI
150
K
IT
• 3/8" drill bit
• Hand drill
• Pliers
• Sharp knife
• Center punch
NCD-5965-1
2178
1
1
1
3
1
2
2
1
4
16
Advertisement
Related Manuals for Firestone 2178
Summary of Contents for Firestone 2178
- Page 1 Control Accessory Kit. This kit was designed to provide connect the air line tubing to the fittings push the tubing inflation control of your Firestone air helper springs. This kit into the fittings as far as possible. If for any reason the...
- Page 2 AIR LINE Air Line & Wiring Diagram ILLUMINATION WIRES GROUND BLACK CONTROL PANEL GROUND BLACK WHITE 1000 AIR LINE AIR LINE Compressor Assembly & Attachment A I G ” S 1 / 8 T I N F I T 1 ” ”...
- Page 3 OCATING A MOUNTING AREA FOR THE GAUGE Select a mounting surface under the dash of your vehicle or other protected location. Mark a 3/16" diameter hole at each of the mounting points, use the air control panel as a template for marking the holes. Drill two 3/16"...
- Page 4 OU ARE NOW READY TO TEST THE SYSTEM With the Ride-Rite air accessory kit and Firestone suspension products installed you are ready to test the system. Turn on the ignition. Push the paddle switch up, air pressure should read on the gauge showing how much air pressure is in the air aprings.