Summary of Contents for SkyTracker MiniTracker
- Page 1 MOTORIZED SEARCHLIGHT MiniTracker INSTRUCTION MANUAL Equipment Type 3200365 • Rev. December 2004 4350 McKinley Street • Omaha, Nebraska 68112 USA Tel (402) 453-4444 • Fax (402) 453-7238 • www.skytracker.com...
- Page 2 Patents, owned by SkyTracker or Ballantyne of Omaha are either issued or pending in this and related concepts. TRADEMARK The name, “MiniTracker” is a trademark owned by Ballantyne of Omaha, and has been registered with the U.S. Patent Office. COPYRIGHT...
- Page 3 The normal warranty will be voided in instances where it is determined that any component of the MiniTracker has been damaged or has failed due to failure to follow procedures or instructions contained in this manual. The completely assembled and operational MiniTracker has all electrical and optical components contained within closed and secured housings.
-
Page 4: Setup And Operation
Entertainment Lighting will provide any required shipping records on request. The four feet of the MiniTracker base are threaded to permit leveling the unit on an uneven floor. The leveling feet are adjustable through a two-inch (5cm) range and can be secured by tightening the locknut provided. - Page 5 “12 o’clock” The lamp positioning controls are accessible through the back cover of the lamphead. Three clearance holes are located around the center air intake cap at the twelve, four, and eight o’clock positions. A #2 phillips screwdriver with a blade “4 o’clock”...
-
Page 6: Maintenance
The slip ring attached to the shaft of the yoke assembly transfers electrical current from the stationary base assembly to the rotating lamphead. Proper maintenance of this item is mandatory to insure the correct operation of the MiniTracker. Brushes and springs are key components and are subject to periodic replacement under normal conditions. - Page 7 Inspect the brushes for wear. If the distance from the top of the insulator to the lower part of the brush spring is 0.093 inch (2mm) or less, replace the brush. Before installing the new brush, inspect the brush contact surface. Remove surface dust, oxidation, pitting, or other contaminants with a wire brush.
-
Page 9: Parts List
PARTS LIST Figure 1 Item Part No. Description 3200407 Blower Intake Cover 3200406 Standoff, Intake Cover (4 req’d.) 6198002 Lamphead Blower (B1) 4082500 Mounting Screw, 8-32 x 2-1/2" Pan Head 3200428 Rear Cover Ring 4100501 Mounting Screw, 10-32 x 1/2" Truss Head 4170114 Weatherseal Washer, #10 3200397 Inner Shell... - Page 10 3200402 Blower Mounting Plate 4080375 Mounting Screw, 8-32 x 3/8" Pan Head (4 req’d.) 3198164 Heyco Strain Relief Bushing 3200537 Light Baffle 4100501 Mounting Screw, 10-32 x 1/2" Truss Head 4170114 Weatherseal Washer, #10 FIGURE 2 MiniTracker Base Assembly No.3200366...
- Page 11 PARTS LIST Figure 2 Item Part No. Description 3200375 Yoke & Column, Welded Assembly 3200372 Top Cap 4100371 Mounting Screw, 10-32 x 3/8" Pan Head 8162004 Barrier Strip 4100751 Mounting Screw, 10-32 x 3/4" Pan Head 3200416 Driven Sprocket 3198118 Roller Chain (3.69 feet req’d.) 3198119 Master Link 3200368 End Panel (2 req’d.)
-
Page 12: Equipment Warranty
SkyTracker/Strong Entertainment Lighting EQUIPMENT WARRANTY SkyTracker/Strong Entertainment Lighting agrees that its products shall be free from defects in materials and workmanship for a period of one year, from the date of original shipment from its factory. This warranty is nontransferable and applies to the original purchaser only. -
Page 13: Wiring Diagram
WIRING DIAGRAM MiniTracker AC Neutral AC Phase S1 “LAMP” S2 “MOTION” MOTOR SPEED CONTROL LAMP POWER SUPPLY IGNITER SOCKET, TYPE G22 Ref. Desig. Part No. Description 6198002 Lamphead Blower, 115 V.AC, 50\60 Hz. 39938000 Base Blower, 115 V.AC, 50\60 Hz.
Need help?
Do you have a question about the MiniTracker and is the answer not in the manual?
Questions and answers