Subscribe to Our Youtube Channel
Related Manuals for IKUSI TNS-101
Summary of Contents for IKUSI TNS-101
-
Page 1: User Manual
Television on IP Networks TNS-101 (Ref. 5114) FTA or MultiCrypt DVB-T ➞ ➞ ➞ ➞ ➞ IP Streamer — Common Interface Configuration and Settings User Manual... - Page 2 Configuration and Setting of the TNS-101 Streamer Module User Manual June 2009 Revision A IKUSI - Ángel Iglesias, S.A. Paseo Miramón, 170 20009 San Sebastián SPAIN Tel.: +34 943 44 88 00 Fax: +34 943 44 88 11 www.ikusi.com...
-
Page 3: Table Of Contents
CONTENTS Introduction ..........................4 This Manual ......................... 4 Product Description ...................... 4 Chapter One - Configuration of the TNS-101 Streamer ............5 Configuration ......................6 -10 Save/Restore Configuration ..................11 General Report ......................12 Chapter Two - TNS-101 Streamer Settings ................13 Input Settings ...................... -
Page 4: Introduction
Access manual supplied in paper format. Product Description TNS-101 streamers are DVB-T to IP gateways designed to broadcast in multicast the services (TV and Radio programmes) issued from FTA or encrypted digital terrestrial reception; in case of encrypted signal, a CAM containing the operator's smart card must fit the front panel slot. -
Page 5: Chapter One - Configuration Of The Tns-101 Streamer
Chapter One - Configuration of the TNS-101 Streamer In this Chapter Configuration ● Save/Restore ● General Report ●... - Page 6 3 options: Configuration, Save/Restore and General Report. Click on Configuration. The Configuration window will appear : Figure 1.2 - Identification card of the Configuration window. Identification The identification card (Figure 1.2) provides basic data on the TNS-101 streamer. The different card fields are completed as follows:...
- Page 7 Configuration "Model": TNS-101. This data cannot be changed. "Serial Number": Informational data which cannot be changed. "Firmware Version": As above. "Identifier": Any name that the installer or operator wishes to assign to the streamer module can be entered here. "Location": Enter the postcode of the installation site if required.
- Page 8 The following card is displayed: Figure 1.3 - Network card of the Configuration window. "Use DHCP to get IP address": If this box is checked, the TNS-101 module will use the DHCP protocol for assigning dynamic IP addresses. Consequently, no data needs to be entered in the next five fields on the tab.
- Page 9 Configuration Password If you want to change the current access password, click on the Password tab. The following card is displayed: Figure 1.4 - Password card of the Configuration window. "Current password": Enter the current password. "New password": Enter the new password which will be required to access the program the next time.
- Page 10 Figure 1.6 - Update Firmware card of the Configuration window. WARNING: The firmware update file will have been previously stored on the PC hard drive. (You can download it from http://www.ikusi.com). Click on Browse... and select the firmware update file from the hard drive. When the file name is in the box, click on Start.
-
Page 11: Save/Restore Configuration
Save/Restore Save/Restore System Settings All of the data established on the streamer module through the various Configuration window tabs can be saved onto a backup file. Inversely, the configuration data saved on an appropriate file can be restored on streamer module. Click on the General menu on the left of the general program screen and click again on the Save/Restore option. -
Page 12: General Report
General Report option. The General Report window is displayed: Figure 1.9 - General Report window This window provides complete information on the TNS-101 module, not only regarding the configuration described in the previous pages, but also in relation to the current settings parameter values and operational status. -
Page 13: Chapter Two - Tns-101 Streamer Settings
Chapter Two - TNS-101 Streamer Settings In this Chapter Input Settings ● Output Settings ● SAP Channel Settings ● CAM User Menu ● SNMP Configuration ●... -
Page 14: Input Settings
Input Input Settings The TNS-100 module settings are grouped into five sections or categories: Input, Output, SAP Channel, CAM User Menu and SNMP. Click on the Settings menu on the left side of the general program screen. A drop down list with the five option for this menu is displayed: Input, Output, SAP Channel, CAM User Menu and SNMP. -
Page 15: Output Settings
Output Output Section Settings Click on the Settings menu on the left of the general programme screen and click again on the Output option. The Output windown will appear: Figure 2.2 - Output window This window is used to select and configure the required services (TV or Radio programmes) from the DVB-T input transport stream as IP streams. - Page 16 Output The Output window allows you to perform three actions: - Add Stream: This adds a new IP stream to the display table. - Edit Stream: Allows you to change the parameters of the IP stream on the dis- play table. - Delete Stream: Deletes an IP stream from the display table.
- Page 17 Output Boxes at the top of the screen: "Multicast Stream Address": Enter the multicast address required for the stream to be added. The available range is from 224.0.0.0 to 239.255.255.255, but it is recommended to reduce it from 224.0.1.0 to 238.255.255.255. See NOTE below. "Port": The default value is 1234.
-
Page 18: Sap Channel Settings
SAP/SDP Channel SAP Channel Settings Click on the Settings menu on the left of the general programme screen and click again on the SAP Channel option. The SAP Channel window will appear: Figure 2.4 - SAP Channel window This menu option is used to configure the announcement and service description SAP/ SDP channel. -
Page 19: Cam User Menu
The procedure is, as aforesaid, similar for all type of CAM modules. When in doubt, contact the vendor of the module. The correct programme de-encrypting is guaranteed only with CAMs validated by IKUSI. Consult on www.ikusi.com the operativity of your CAM. -
Page 20: Snmp Cofguration
(management station). It has two sections: Configuration and Traps. Configuration Section : "MIB" : Click on Download to download the MIB of the TNS-101 streamer. "SNMP Agent" : Tick the box if you want to activate the SNMP agent implemented in the streamer module. - Page 21 Link Link Link Link Link +13V +13V 300 mA 300 mA :700 mA TOT (MAX) :700 mA TOT (MAX) Figure 2.10 - Example of TNS Headend with monitor redundant power system. Contains 7 TNS-101 streamers and 2 CFP-702 power supplies.
-
Page 22: Chapter Three - Tns-101 Streamer Status Information
Chapter Three - TNS-101 Streamer Status Information In this Chapter Status Information ●... -
Page 23: Status Information
"BER": Expresses in scientific notation the channel BER value for the input signal. "C/N (dB)": The value in dB of the carrier/noise ratio of the input signal. "Number of Streams": Number of IP streams currently transmitted by the TNS-101 module. -
Page 24: Chapter Four - Tns-101 Streamer Reports
Chapter Four - TNS-101 Streamer Reports In this Chapter Input Services ● Output Streams ● System Logs ●... -
Page 25: Input Services
Input Services Input Services Click on the Reports menu on the left of the general program screen and click again on the Input Services option. The Input Services window appears: Figure 4.1 - Input Services Window The Input Services window shows the full information on each of the services contained in the DVB-T input transport stream. -
Page 26: Output Streams
Output Streams Output Streams Click on the Reports menu on the left of the general program screen and click again on the Output Streams option. The Output Streams window will appear: Figure 4.2 - Output Streams window The Output Streams window shows all IP streams that have been created for this mo- dule. -
Page 27: System Logs
System Logs System Logs Click on the Reports menu on the left of the general program screen and click again on the System Logs option. The System Logs window will appear: Figure 4.3 - System Logs window... - Page 28 IKUSI - Ángel Iglesias, S.A. Paseo Miramón, 170 20009 San Sebastián SPAIN Tel.: +34 943 44 88 00 Fax: +34 943 44 88 11 www.ikusi.com ER-0149/1996...
Need help?
Do you have a question about the TNS-101 and is the answer not in the manual?
Questions and answers