SAFETY INFORMATION CAUTION This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
Page 3
[ Important symbols for good services ] In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely. When you find the procedures bearing any of the symbols, be sure to fulfill them: 1. Product safety You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual.
2. EXPLODED VIEWS AND PARTS LIST OTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List. • Screw adjacent to mark on the product are used for disassembly. •...
Page 9
(2) CONTRAST TABLE DEH-1600/XU/UC, DEH-16/XU/UC and DEH-6/XU/UC are constructed the same except for the following: Mark Description DEH-1600/XU/UC DEH-16/XU/UC DEH-6/XU/UC 11-1 Owner's Manual YRD5003 YRD5003 YRD5004 11-2 Installation Manual YRD5008 YRD5008 YRD5009 11-4 Caution Card Not used CRP1294 CRP1294 Carton YHG5004 YHG5005 YHG5006...
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM 3.1 BLOCK DIAGRAM TUNER AMP UNIT 10 9 8 18 19 20 21 FM/AM TUNER UNIT IC 5 IC 3 EEPROM 3.3V 5.0V ANTENNA CN401 AM ANT FMRF IC 2 2.5V IC 1 FM ANT 3.3V FMRF MIXER, IF AMP...
Page 17
RESET IC 961 S-80834CNY PRE OUT CN352 Q352 TUNPCE2 TUNPCE1 TUNPDI TUNPDO TUNPCK VDD REGULATOR Q911 Q912 SYSTEM CONTROLLER DALMON CN901 IC 601(1/2) PE5330C:DEH-1600/XU/UC DEH-16/XU/UC BACKUP SENSE PE5331B:DEH-6/XU/UC B.UP FUSE BSENS BACK UP Q931 ASENS ACC SENSE B REMOTE IC 551 B.UP TPD1018F B.UP...
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE) Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST". Large size SCH diagram CN701 Guide page Detailed page DEH-1600/ DEH-16/XU CD:+0.35dBs FM:-15.5dBs AM:-30.0dBs DEH-1600/XU/UC DEH-16/XU/UC DEH-6/XU/UC DEH-1600/XU/UC...
3.3 KEYBOARD UNIT For resistors and capacitors in the circuit diagrams, their resistance values or capacitance values are expressed in codes: Ex. *Resistors Code Practical value 12k ohms D1801 ILM COLOUR IL1801,1802 10k ohms MA152WK DEH-1600/XU/UC *Capacitors DEH-16/XU/UC MA152WK Code Practical value 0.01uF DEH-6/XU/UC...
Page 25
D1802 R1816-1818 LCD1801 D1801 D1803-1809 CAW1802 MA152WK MA152WA YAW5012 MA152WK MA152WA YAW5001 Not used Not used KEYBOARD UNIT DEH-1600/XU/UC DEH-16/XU/UC 40mA, 14V DEH-1600/XU/UC...
3.4 CD MECHANISM MODULE PICKUP UNIT(P10)(SERVICE) MOTOR DRIVER CXB6007 SPINDLE MOTOR CXB8933 LOADING/CARRIAGE MOTOR BA5835FP 3.3V REGULATOR DEH-1600/XU/UC...
Page 27
CD CORE UNIT(S10.1) RF AMP / SERVO / DSP / DAC / LPF SIGNAL LINE FOCUS SERVO LINE TRACKING SERVO LINE CARRIAGE SERVO LINE SPINDLE SERVO LINE SWITCHES: CD CORE UNIT (S10.1) S901 : HOME SWITCH..ON-OFF S902 : CLAMP SWITCH..ON-OFF S903 : DSCSNS SWITCH..ON-OFF S904 : 12EJ SWITCH....ON-OFF S905 : 8EJ SWITCH....ON-OFF...
Page 28
- Waveforms Note : 1. The encircled numbers denote measuring points in the circuit diagram. 2. Reference voltage REFO1(1.65V) 1 DSCSNS 1 DSCSNS 5 SIN 5V/div 500ms/div 5V/div 500ms/div 1V/div 2s/div 2 CLCONT 2 CLCONT 6 CIN 5V/div 5V/div 500mV/div 3 LOEJ 3 LOEJ 7 TIN...
Page 29
# RFAGC # RFAGC # RFAGC 1V/div 500ms/div 1V/div 5ms/div 1V/div 500µs/div 0 TE 0 TE 7 TIN 500mV/div 500mV/div 1V/div 7 TIN 7 TIN 0 TE 500mV/div 500mV/div 1V/div 8 FIN 1V/div 32 Track Jump 100(32x3) Track Jump When reproducing black dots(1mm) Ref.: Ref.: Ref.:...
4. PCB CONNECTION DIAGRAM 4.1 TUNER AMP UNIT TUNER AMP UNIT CORD ASSY NOTE FOR PCB DIAGRAMS 1.The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic dia- gram.
Page 31
SIDE A REAR OUTPUT ANTENNA JACK FRONT CN1801 DEH-1600/XU/UC...
5. ELECTRICAL PARTS LIST NOTE: Parts whose parts numbers are omitted are subject to being not supplied. • The part numbers shown below indicate chip components. • Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS..) CKS.., CCS.., CSZS..Circuit Symbol and No. Part No.
Page 39
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 605 RS1/16S221J C 163 CCSRCH100D50 R 606 RS1/16S104J C 164 CCSRCH100D50 R 607 RD1/4PU222J C 165 CKSRYB104K16 R 608 RS1/16S0R0J C 166 CEJQ470M10 C 167 CEJQ100M16 R 609 RD1/4PU473J R 610 RD1/4PU681J...
Page 40
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. IL 1801 Lamp 40mA,14V CEL1662 D 1805 SML-310PT IL 1802 Lamp 40mA,14V CEL1662 D 1806 SML-310PT D 1807 SML-310PT LCD1801 YAW5012 D 1808 SML-310PT D 1809 SML-310PT RESISTORS D 1810 CL-490S-WF-SD R 1801...
Page 41
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 204 RS1/16S1002D C 220 CKSRYB104K16 R 205 RS1/16S1002D C 221 CKSRYB104K16 C 222 CKSRYB103K25 R 206 RS1/16S1002D R 207 RS1/16S1002D C 223 CCSRCH680J50 R 208 RS1/16S1002D C 224 CCSRCH470J50 R 209 RS1/16S1002D...
6. ADJUSTMENT 6.1 FREQUENCY CHECK FOR CLOCK - Adjustment Point +14.4V BACK UP DC Regulated Power Supply TUNER AMP UNIT(SIDE B) IC601 Frequency Counter Specification Measuring Point Note 1. ACC, B.UP ON 786,432±31.5Hz IC601 14pin(PCL) 2. IC601 15pin : 5V DEH-1600/XU/UC...
6.2 CD ADJUSTMENT 1) Cautions on adjustments 2) Test mode • In this product the single voltage (3.3V) is used for the This mode is used to adjust the CD mechanism module. regulator. The reference voltage is the REFO1 (1.65V) •...
6.3 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT • Note : The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU unit for the CD mechanism module.
6.4 ERROR MODE - Error Messages If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the users and also for facilitating trouble analysis and repair work in servicing.
7. GENERAL INFORMATION 7.1 DIAGNOSIS 7.1.1 DISASSEMBLY Removing the Case (not shown) 1. Remove the Case. CD Mechanism Module Removing the CD Mechanism Module (Fig.1) Remove the four screws. Disconnect the connector and then remove the CD Mechanism Module. Removing the Grille Assy (Fig.1) Release the two latchs and then remove the Grille Assy.
Page 48
- How to assemble Keyboard Unit 1. Assemble them in order from "1" to "8". (See the figure below.) 2. After that, bend the crows (7 in total) until they get the right angles with the marks printed on "8". Note) If "5"...
Page 49
- How to hold the Mechanism Unit 1. Hold the top and bottom frame. 2. Do not squeeze top frame's front portion too tight, because it is fragile. Do not squeeze. - Removing the Upper and Lower Frames 1. With a disc clamped, remove the four springs (A), Upper Frame the two springs (B), the two springs (C), and the four screws.
Page 50
- Removing the Pickup Unit 1. Apply shorting solder to the Pickup flexible cable. Disconnect the cable. 2. Set the mechanism to the clamp mode. 3. Remove the lead wires from the inner holder. 4. Remove the washer, styling holder, change arm, and pickup lock arm.
7.2 PARTS 7.2.1 IC - Pin Functions(PE5330C,PE5331B) Pin No. Pin Name Function and Operation MODEL1 Model port 1 Not used AVSS A/D GND Not used AVREF1 A/D converter reference voltage KYDT Key data input DPDT Display data output Not used TUNPDI PLL IC data input TUNPDO...
Page 53
Pin No. Function and Operation Pin Name PLL lock sense input LDET Not used ACC sense input ASENS BSENS Back up sense input Grille detach sense input DSENS ATAPI HOST interrupt request input INTRQ VSS0 Power supply VDD1 Crystal oscillator connection pin Crystal oscillator connection pin Connect to GND IC(VPP)
Page 54
- Pin Functions(PD6340A) Pin No. Pin Name Function and Operation SEG4-0 LCD segment output COM3-0 LCD common output VLCD LCD drive power supply 11-14 KST3-0 Key strobe output 15,16 KDT0,1 Key data input (analogue input) Remote control reception input DPDT Display data input Not used KYDT...
Page 55
- Pin Functions(UPD63712AGC) Pin No. Pin Name Function and Operation Output of LD Input of PD Assignment of pickup polarity AVDD Power supply for the analog system DGND Ground for digital circuits RFOK Output of RFOK INTQ Interruption signals to the external microcomputer Input of reset Command/Parameter discrimination signal input Data strobe signal input...
Page 56
Pin No. Pin Name Function and Operation TESTEN Connected to GND 62-66 TEST4-0 Connected to GND ADGND GND for DAC Output of EFM signals Input of asymmetry ADVDD Power supply for DAC Input of RF 72, 73 EQ2, 1 Equalizer 2, 1 Reversal input of RF RF2- Reversal input of RF2...
Page 57
- Pin Functions(BA5835FP) Pin No. Pin Name Function and Operation Input pin for reference voltage OPIN2(+) Input pin for non-inverting input for CH2 preamplifier OPIN2(-) Input pin for inverting input for CH2 preamplifier OPOUT2 Output pin for CH2 preamplifier OPIN1(+) Input pin for non-inverting input for CH1 preamplifier OPIN1(-) Input pin for inverting input from CH1 preamplifier...
Page 58
- FM/AM Tuner Unit 10 9 8 18 19 20 21 IC 5 IC 3 EEPROM 3.3V 5.0V AM ANT FMRF IC 2 2.5V IC 1 FM ANT 3.3V FMRF MIXER, IF AMP DET, FM MPX RF adj ANT adj CF52 CF51 IC 4...
7.3 OPERATIONAL FLOW CHART Power ON VDD1=5V Pin 68 BSENS Pin 64 BSENS=L ASENS Pin 63 ASENS=L DSENS Pin 65 DSENS=L Starts communication with Grille microcomputer. 300ms swvdd←L Pin 21 300ms In case of the above signal, the communication Source keys with Grille microcomputer may fail.
7.4 CLEANING Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DEH-1600/XU/UC...
Page 67
- DEH-1600/XU/UC, DEH-16/XU/UC About the fixing screws for the front panel About the f x ng screws for the front panel If you do not operate the Detaching and Replacing the Front Panel Function, use the sup- plied fixing screws and fix the front panel to this unit. CBA1488 CBA1488 DEH-1600/XU/UC...