Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com 4.9.3 System Status........................60 4.9.4 Call Statistics.........................61 4.9.5 Inter-call Stats........................62 4.10 Save and Reboot..........................63 Typical Used Scenario..........................64 Landing from IP to Mobile Network..................64 Access from Mobile Network to IP..................65 Introduction 1.1 Overview A VoIP GSM/CDMA/WCDMA Gateway is a device which reduces costs when calling from a fixed telephone line to mobile network.
32 concurrent calls and perfectly support G729a/b/e、G723.1、G.711 a/u law and iLBC codecs at the same time. RO32G series VoIP Gateway includes: RO32G-32, RO32G-128, most of their features and structure are same, please check the following table about the difference:...
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com 2.2 Appearance Here, we take RO32G-128 as the sample to show the interface and indicators at the front and back panel. Back Panel Front Panel 32 Antennas 1 USB Serial Port (Baudrate 115200) ...
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com 3 Equipment Installation This chapter describes how to install a new GSM/CDMA/WCDMA Gateway to a physical network environment, how to initialize it and start it in a proper way. 3.1 Network Setup Network is a prerequisite to install GSM/CDMA/WCDMA Gateway. The following figure shows the topology of LAN with a VoIP Gateway connected.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Equipment IP Address The default IP of GSM/CDMA/WCDMA Gateway WAN port is 192.168.1.67 3.3 Equipment Connection Follow the steps below to install the GSM/CDMA/WCDMA Gateway to LAN. 1)Fix the antenna to the GSM/CDMA/WCDMA Gateway.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com 4 Web Settings This chapter describes how to set up GSM/CDMA/WCDMA Gateway through Web Page. There is a built-in web server which can be accessed at URL: http://GATEWAY_IP/, while GATEWAY_IP is the WAN IP address of the GSM/CDMA/WCDMA Gateway, such as 192.168.1.67.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Password: root It is recommended to use IE or FireFox to access the web pages. After successfully logged in, the main page to set Gateway is as following: 4.2 Basic Settings Basic Settings will be described in this paragraph. The most frequently modified parameters and most of the individual parameters are listed in this page.
Page 14
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Dynamic IP:You can get IP address ,IP Mask ,Default Gateway and DNS Server dynamically from your DHCP server. PPPoE:In this mode,you can use GSM/CDMA/WCDMA device to dail-up network. You can set User Name and Password which you get from your ISP. And you also can set MTU and Service Name.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Phone Number: Specify the caller phone number for SIP client. It can also be regarded as the SIP port number which can be called. Account: Specify the SIP account for registration.
Page 16
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Expiration Period: Specify the expiration period for registration. Local Port: Specify the local port used to register to SIP server. Multiple Port Support: Specify whether support to register to SIP server with different SIP Account.
Page 17
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Proxy Encryption is a good solution for protecting ip from blocking and save bandwidth about 50%. Fields are specified as following: Proxy Encryption: Specify whether enable it, if enabled, system will automatically disable common encryption.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com here are left empty, the combination of test and 888888 will be used for all SIP accounts to register to SIP Server. When the gateway register on the server successfully, the status will show ready.
Page 19
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com It’s for choosing the frequency band and whether lock the operator, generally, we don’t enable the lock the operator. When the gateway can’t detect the sims, we need to enable Unnormal Sim Supp.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com feature. The columns are specified as following: Port No: The GSM/CDMA/WCDMA Gateway mobile port. Each port contains one or four card slots. Port No starts from 1 to 32. Main Access: Specify whether the current port is used for access or not. If set to Enable, any call made to the card in this port will be redirected to the phone number on any other idle port which is not set as a main access.
Page 21
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Fields are specified as following: Max Channels: Specify the max base stations Lowest Valid Signal: Specify the lowest valid signal Switch period: Specify the period of switching base station Base Balancing: Specify whether enable base balancing, we suggest disable it.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Port No: The GSM/CDMA/WCDMA Gateway mobile port. Each port contains one or four card slots. Port No. starts from 1 to 32. Base Selection: the default base selection mode is auto which makes the devices to...
Page 23
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com IMEI A: Specify the IMEI for card A of the port. IMEI B: Specify the IMEI for card B of the port. IMEI C: Specify the IMEI for card C of the port.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Click button Submit on the right to save the old data record. Delete Click Delete on the right of each record to delete the current record. A message box will be popped for delete confirmation.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Port No. starts from 1 to 32. PIN A: Specify the PIN for card A of the port. PIN B: Specify the PIN for card B of the port. PIN C: Specify the PIN for card C of the port.
Page 26
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Fields are specified as following: Forward Protocol: Specify the forward protocol http. URL: Specify the sms server URL. Username: Specify the username. Password: Specify the password. Sender: Specify the sender.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com By Duration: Gateway will start sms sending by the device online time, and the time between minimum minutes and maximum minutes. By Consecutive Failed Calls:Gateway will start sms sending by consecutive failed calls.
Page 28
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com The screenshot below shows the operation mode to receive sms. Fields are specified as following: Port No: The GSM/CDMA/WCDMA Gateway mobile port. Each port contains one or four card slots. Port No starts from 1 to 32.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Port: Specify the port. Sender: Specify the sms sender. Time: Specify the sms receive time. Content: Specify the sms content. Back: Back to the SMS content web page.
Page 30
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Reset When Switching: To clear this condition if other conditions to be met when you enable two or more Lock/switch card conditions Accumulated Duration: Specify the period to check. Locking Duration: Specify how long the card will be locked. 0 means no lock,-1 means permanent lock The following is to set condition of accumulated connected calls.
Page 31
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Accumulated calls: Specify the max running duration of the card. If the accumulated call times reaches or exceeds this value, the card will be locked if this condition is enabled. Locking Duration: Specify how long the card will be locked.
Page 32
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Reset When Switching: To clear this condition if other conditions to be met when you enable two or more Lock/switch card conditions USSD Query: Send USSD query command before switching. No-Alert calls: Specify the max number of No-Alert calls on this card. If the number of consecutive No-Alert calls reaches or exceeds this value, the card will be locked this condition is enabled.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com accumulated number of failed calls will be used as a condition for system to check. Reset When Switching: To clear this condition if other conditions to be met when you enable two or more Lock/switch card conditions ...
Page 34
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Fields are specified as following: Port Inter-Calling: Specify whether enable port inter-calling. Min Call Duration: Specify the minimum call duration. Max Call Duration: Specify the maximum call duration. The screenshot below shows the operation mode to set conditions settings of port...
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com 4.4.9 SIM Num Settings The screenshot below shows the operation mode to get Local Number by USSD Fields are specified as following: Using USSD: when enable it, gateway will get the sim number by ussd command ...
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Fields are specified as following: Port No: The GSM/CDMA/WCDMA Gateway mobile port. Each port contains one or four card slots. Port No starts from 1 to 32. Number A: Specify the number for card A of the port ...
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com The module here means the The GSM/CDMA/WCDMA mobile port. Button Restart is used to restart this module. Button Stop is used to stop this module. Button Start is used to start this module.
Page 38
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Fields are specified as following: Billing: Specify whether enable GSM/CDMA/WCDMA billing or not. If set to Enabled, system will bill the outbound calls for the port which has been assigned with billing tariffs.
Page 39
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Name: Specify the provider name. Caution Balances: Specify four balances separated by semi-colon. Each balance corresponds to one Keyword from left International keys to right other keys in keyword List table. Each caution balance is a threshold for system to get card balance through USSD if current balance is less than this threshold.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Tariff: Specify the tariff detail. In the picture,the tariff means 10 value will be deduct per 60 seconds. Click button Submit on the right to save the new data record. Edit All the records are displayed in list. Two operations are provided on the right of each record.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com The columns are specified as following: Port: The GSM/CDMA/WCDMA Gateway mobile port. Each port contains one or four card slots. Port No starts from 1 to 32. Status: it shows the sim status.
Page 42
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Add New Click button Add New to expand the data input area to add new data. Fields are specified as following: Data status: Mark the status of current data record. Option values are Add/Edit.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com box will be popped for delete confirmation. Another shortcut button is also provided on the top right of Data List to delete multiple selected records in batch. A message box will be popped for confirmation ofbatch delete.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Fields are specified as following: Prefix: The original prefix in phone number. Manipulated Prefix: Specify the digits with which the value specified by Prefix will be substituted. Take the value in screenshot as an example, the prefix 9999 in dialed number will be substituted with 0.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Fields are specified as following: Callee Prefix: Specify the callee prefix. Digits Stripped: Specify the digits which are stripped. Digits Added: Specify the digits which are added. Take the value in screenshot as an example, the callee ID is 00880xxxxx, we specify 0080 as the callee prefix,strip 4 digits and don’t add digits,when dial...
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Fields are specified as following: Callee Prefix: Specify the callee prefix of black list. Callee Length: Specify the callee length of black list. Take the value in screenshot as an example, if the callee id likes 032xxxx, and the length is 12 digits, the call will be rejected by the gateway.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Advanced Settings Advanced Settings focus on the high level usage of GSM/CDMA/WCDMA Gateway. It includes: Network Voice and Codec Other Settings These sub topics will be introduced separately below. 4.6.1 Network The screenshot below shows the operation mode to set VPN settings, and the protocol of vpn is pptp.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com and wan IP is 192.328.1.67, the web pages then should be accessed through URL: http://192.328.1.67:8080/ from this computer. The field Telnet Port is used to change the default port of telnet service. 4.6.2 Voice and Codec The screenshot below shows the operation mode to set voice settings.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com The Busy Tone indicates that the called customer’s line has been reached but that it is busy, being wrong, or on permanent signal. W hen an operator applies a busy signal, it is sometimes called a busy-back tone.
Page 50
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Port: The GSM/CDMA/WCDMA Gateway mobile port. Each port contains one or four card slots. Port No. starts from 1 to 32. Type: Values are GSM/CDMA. (According to your module.) Disable: Specify whether enable or disable this port.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Forbid GSM Call: Specify whether need to prevent the PSTN incoming call. If set to enable, any of the incoming calls whose callerid is not in the white list specified in white Number List will be prevented.
Page 52
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com The screenshot below shows the operation mode to manage system user. Default User The default system user account is root. This account can’t be deleted and only Password and Privilege can be modified for this account.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Click Delete on the right of each record to delete the current record. A message box will be popped for delete confirmation. Another shortcut button is also provided on the top right of Data List to delete...
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com If ERM is enabled and correctly set, the GSM/CDMA/WCDMA will register to ERM server and set up the connection between itself and ERM server. Administrator can login ERM server and monitor all the registered GSM/CDMA/WCDMA Gateways. Commands can also be sent from ETMS server to certain gateway for management.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com Fields are specified as following: Auto Ping: Specify whether enable auto ping. IP Address: Specify the ip address. Packet Size: Specify the packet size. Duration: Specify the ping duration ...
Page 57
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com The screenshot below shows the GSM/CDMA/WCDMA Gateway port LED status. Different LED color stands for different port status. Note: LED A/B/C/D displays in accordance with the lights on the front board of GSM/CDMA/WCDMA Gateway. Port 1 to 32 relate to the physical port of GSM/CDMA/WCDMA Gateway.
Page 58
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com The screenshot below shows the GSM/CDMA/WCDMA Port Balance. The screenshot below shows the port status in detail.
Page 59
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com The status columns are specified as following: Port No: The physical port sequence from 1 to 32. Module Detected: Specify whether port module has been detected or not. Option values are Yes/No.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com 4.9.2 Call Status The screenshot below shows the live call status. The status columns are specified as following: Port No: The physical port sequence from 1 to 32. Type: GSM of CDMA Currently GSM/CDMA/WCDMA is regarded as GSM.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com 4.9.4 Call Statistics The screenshot below shows the call statistics information for analysis.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com The status columns are specified as following: Port No: The physical port sequence from 1 to 32. Calls: Specify the total calls made out from this port since the last start up of system.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com The status columns are specified as following: Port No: The physical port sequence from 1 to 32. State: Specify the call status. Duration: Specify the call duration. Incoming calls: Specify the total incoming calls since the last start up of inter calling system.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com 5 Typical Used Scenario This chapter presents some typical used scenarios for reference. 5.1 Landing from IP to Mobile Network GSM/CDMA/WCDMA Gateway is now used more and more for telephone carriers to land their IP calls to mobile network. It plays the role of converting IP telephone signal to GSM telephone sign al , relaying the media strea m be t we e n IP network and Mobile network.
Opptel Co., Ltd web: www.opptel.com E-mail: opptel@opptel.com 5.2 Access from Mobile Network to IP GSM/CDMA/WCDMA Gateway can be used as the access from mobile network call made mobile card inserted into GSM/CDMA/WCDMA Gateway will be routed to IP network and connected to Softswitch server.