Table of Contents
Advertisement
Quick Links
Installation instructions for part 99-9613
Harley-Davidson 1998-2013
KIT FEATURES
• ISO DIN radio provision
• ASWC-1 included, for retention of handlebar controls
• 44-UA20 antenna included
KIT COMPONENTS
• A) Radio housing with rubber gasket • B) (4) 1/2" long button-head cap screws
• C) Wiring harness (not shown)
A
WIRING & ANTENNA CONNECTIONS
Wiring Harness: • Included
Antenna: • 44-UA20 included
Steering wheel control interface: • Included
METRA. The World's best kits.
®
(FL models with fairings)
99-9613
B
™
metraonline.com
Table of Contents
Fairing Disassembly
– Harley-Davidson FLH
(batwing fairing)
1998-2013 .......................................................2-3
– Harley-Davidson Roadglide
(sharknose fairing)
1998-2013 .......................................................4-5
Kit Assembly ...........................................................6
Wiring Instructions ................................................ 7
Final Assembly ...................................................... 7
Handlebar Control Settings ..............................8-11
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Socket wrench: (T-25 Torx, T-27 Torx, 1/2", 3/16 hex)
CAUTION!
All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
© COPYRIGHT 2004-2017 METRA ELECTRONICS CORPORATION
Advertisement
Table of Contents
Related Manuals for Metra Electronics 99-9613
Summary of Contents for Metra Electronics 99-9613
- Page 1 ® Installation instructions for part 99-9613 Table of Contents Harley-Davidson 1998-2013 Fairing Disassembly (FL models with fairings) 99-9613 – Harley-Davidson FLH (batwing fairing) 1998-2013 ............2-3 – Harley-Davidson Roadglide (sharknose fairing) KIT FEATURES 1998-2013 ............4-5 • ISO DIN radio provision Kit Assembly ............6 •...
- Page 2 ® 99-9613 Fairing Disassembly FLH/Batwing models: 1. Cover the front fender. 2. Remove the (2) T-27 Torx bolts from the inner fairing (under mirrors). Step 4 (Figure A, step 2) 3. Remove the (2) T-27 Torx bolts from the outer edges of the inner fairing near the fork tubes (facing forward).
- Page 3 ® 99-9613 Fairing Disassembly FLH/Batwing models: (cont.) 6. Lift away and unplug the headlight to remove the outer fairing. (Figure B) 7. Extract the (2) 3/16” Allen bolts from each side of the radio housing. (Figure C) 8. Remove the factory radio.
- Page 4 ® 99-9613 Fairing Disassembly Roadglide/Sharknose models 1. Loosen the (6) T-25 Torx bolts from Step 1 Step 1 the bottom, middle and top of the left and right sides of the inner fairing. (Figure A) Continued on the next page...
- Page 5 ® 99-9613 Fairing Disassembly Roadglide/Sharknose models (cont.) 2. Use a 1/2” socket or box wrench to remove the (2) acorn nuts that hold each turn signal at the lower fairing. Let the signals hang loose. (Figure B) 3. Lift away the fairing, unplug the headlights, and then remove.
-
Page 6: Kit Assembly
® 99-9613 Kit Assembly ISO DIN radio provision Optional 1. Remove the metal DIN sleeve and spacers if needed trim ring from the aftermarket radio. 2. Slide the radio into the radio housing with rubber gasket and secure with the screws supplied with the radio. -
Page 7: Wiring Instructions
® 99-9613 Wiring Instructions From the wiring harness to the aftermarket radio: • Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow wire to the Brown wire. • Connect the Black wire to the ground wire. -
Page 8: Handlebar Control Settings
® 99-9613 Final Assembly Handlebar Control Settings 1. Connect the 44-UA20 (provided), and complete all necessary connections to the L.E.D. Feedback radio, but do not connect the ASWC-1 just yet. The (17) Red L.E.D. flashes represent which brand radio the ASWC-1 is connected to. - Page 9 ® 99-9613 Handlebar Control Settings (Cont) Attention: Radio Legend Axxess Updater App can also be used to program the following (3) sub- sections as well, pending that the interface has been initialized and programmed. 1 - Eclipse (Type 1) 6 - Pioneer/Jensen...
- Page 10 ® 99-9613 Handlebar Control Settings (Cont) Remap Buttons Button Assignment Legend The interface has the ability to change the button assignment for the handlebar 10 - Band 1 - Not allowed control buttons, except Volume-Up and Volume-Down. Follow the steps below to...
-
Page 11: Handlebar Control Settings
® 99-9613 Handlebar Control Settings (Cont) Dual Assignment (long button press) Dual assignment legend 1 - Not allowed 10 - Band The ASWC-1 has the capability to assign two functions to a single button, except Volume-Up and Volume-Down. Follow the steps below to program the... -
Page 12: Installation Instructions For Part
® Installation instructions for part 99-9613 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated.
Need help?
Do you have a question about the 99-9613 and is the answer not in the manual?
Questions and answers