Related Manuals for TESSERA FL-850/F1L-100
Summary of Contents for TESSERA FL-850/F1L-100
- Page 1 FL-850/F1L-100 FL-850/F1L-100-S Hardware Manual Date published: December 2017 (4th Edition) Tessera Technology Inc. - 1 -...
- Page 2 Tessera Technology Inc. products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of Tessera Technology Inc.
-
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ......................... 4 FEATURES........................... 5 CAN ............................. 6 ..........................8 ........................... 9 ..........................10 THERNET ........................11 ERIAL SELECT 2.5.1 LCD ........................... 12 2.5.2 RS-232C ........................15 2.5.3 USB Serial Conversion .................... 16 ........................17 WITCH ..........................18 OLUME .......................... -
Page 4: Introduction
1 Introduction In this document, features and hardware specifications of FL-850/F1L-100, which the 32-bit single-chip microcomputer RH850/F1L-100 from Renesas Electronics Corporation is mounted, are described. - 4 -... -
Page 5: Features
2 Features RS-232C FlexRay Volume IEBus Power Serial select Ethernet CPU Board Push Switch - 5 -... -
Page 6: Can
The CAN controller of the microcomputer is connected to the CAN transceiver (TJA1040). It supports CAN physical layer. Also, CAN bus signal is connected to DSUB 9pin female connector. CAN 3 CAN 2 CAN 1 CAN 0 CAN B CAN A One terminal can be selected by using jumpers from maximum of three multipurpose terminals, and can be connected to CAN transceiver. - Page 7 Following table shows the connection of RH850/F1L. Jumper Connecter P10_1/TAUD0I3/TAUD0O3/CAN0TX/PWGA1O/TAPA0UN/CSIH1SC/MODE0 P0_0/TAUD0I2/TAUD0O2/RLIN20RX/CAN0TX/PWGA10O/CSIH0SSI/DPO/RESETOUT P10_0/TAUD0I1/TAUD0O1/CAN0RX/INTP0/CSCXFOUT/PWGA0O/TAPA0UP/CSIH1SI CANA P0_1/TAUD0I4/TAUD0O4/CAN0RX/RLIN20TX/INTP0/PWGA11O/CSIH0SI/APO P9_1/INTP11/PWGA9O/TAUD0I2/TAUD0O2/KR0I5/CSIH2CSS1/ADCA0I3S MODEA Short P10_7/TAUD0I15/TAUD0O15/CSIG0SC/ENCA0TIN1/PWGA4O/CAN1TX P0_3/TAUD0I8/TAUD0O8/RLIN30RX/CAN1TX/DPIN1/PWGA13O/CSIH0DCS/CSIH0SO/INTP10 CANB P10_6/TAUD0I13/TAUD0O13/CSIG0DCS/CSIG0SO/ENCA0TIN0/ADCA0SEL2/CAN1RX/INTP1 JP10 P0_2/TAUD0I6/TAUD0O6/CAN1RX/RLIN30TX/PWGA12O/CSIH0SC/INTP1/DPO P9_2/KR0I6/PWGA20O/TAPA0ESO/CSIH2CSS2/ADCA0I9S JP11 MODEB Short P0_4/RLIN31RX/INTP11/CAN2TX/INTP11/PWGA10O/CSIH1SI/SELDP0/DPIN8 JP22 CAN0 P0_5/CAN2RX/INTP2/RLIN31TX/DPIN9/SELDP1/CSIH1DCS/CSIH1SO JP23 P9_3/KR0I7/PWGA21O/CSIH2CSS3/ADCA0I10S JP20 MODE0 Short JP26 CAN1 JP27 JP24 MODE1 Short JP30...
-
Page 8: Flexray
FlexRay RH850/F1L does not have FlexRay controller, therefore it cannot use FlexRay. FlexRay A FlexRay B Default Settings Jumper Short Jumper Short JP19 All Open JP41 JP13 JP11 All Open JP12 JP14 JP15 JP18 JP10 JP17 JP16 Notes These parts are not mounted in the product in December 2017 and afterwards. - 8 -... -
Page 9: Iebus
IEBus RH850/F1L does not have IEBus controller, therefore it cannot use IEBus. JP42 JP43 Default Settings JP43: Open JP42: Short CN4 Pin Function Name Number (+) Bus Output, (+) Receiver Input (－) Bus Output, (－) Receiver Input Notes These parts are not mounted in the product in 2014 and afterwards. - 9 -... -
Page 10: Ethernet
Ethernet RH850/F1L does not have MAC controller, therefore it cannot use Ethernet. SW16 SW18 SW17 The function of Ethernet is not used, and make the following dip switches all turning off. There is a possibility of breaking when turning it on. ・SW16 (Default OFF) ・SW17 (Default OFF) ・SW18 (Default OFF) -
Page 11: Serial Select
Serial select It can be connected by selecting the microcomputer's UART terminal to "LCD", "RS-232C", and "USB Serial Conversion". The terminals for using UART can be selected by DIP switch (SW1, SW4, and SW6). ※ Do not set multiple ON within a group. P10_10/TAUD0I14/TAUD0O14/RLIN30TX/ENCA0BIN/PWGA7O/CSIH0CSS1 P0_2/TAUD0I6/TAUD0O6/CAN1RX/RLIN30TX/PWGA12O/CSIH0SC/INTP1/DPO P11_5/INTP5/RLIN33TX/PWGA30O/CSIH3SI... -
Page 12: Lcd
2.5.1 LCD Words can be displayed on LCD panel by sending data to UART that is connected to LCD. "Binary mode" to display hexadecimal and "ASCII mode" to display ASCII characters can be selected by the DIP switch (SW7). Initial screen displays when you press the reset switch on CPU board. Adjust LCD Contrast Connector for debugging the microcomputer (78K0/KF2) for LCD control. - Page 13 Binary Mode 2 (SW7_1:ON, SW7_2:OFF, SW7_3:ON) It displays the hexadecimal data as sent without entering space between 1Byte data. It can display 16Byte in 1 screen. It scrolls 1 line when it received 17Byte of data. (example） URTH?TX = 0x01; TXWait(); URTH?TX = 0x02;...
- Page 14 ASCII Mode Ver.2 (SW7_1:OFF, SW7_2:Any, SW7_3:Any) It displays the characters as sent. It can display 16 characters in 1 line. It scrolls 1 line when it received 17th character or linefeed code (0x0D: \r ). URTH?TX = ‘F’; TXWait(); (example） URTH?TX = ‘l’;...
-
Page 15: Rs-232C
2.5.2 RS-232C UART that is connected to "RS-232C" can send and receive signals with the RS-232C level of D-SUB9 pin connector. Use a cross cable when you connect to PC. RS-232C RS-232C D-SUB Connector Pin Number Signal N.C. N.C. N.C. RTS(N.C.) CTS(N.C.) N.C. -
Page 16: Usb Serial Conversion
2.5.3 USB Serial Conversion UART that is connected to "USB serial conversion" can communicate with the COM port of PC through USB microcomputer (uPD78F0730). USB driver is stored in the same media as this manual. When you encountered a warning "Windows Logo Test"... -
Page 17: Push Switch
Push Switch 4 interrupt signals can be connected to microcomputer's interrupt terminals. The signal can be set to High by pressing H button, and to Low by pressing L button. It becomes High by reset signal of the CPU. Also, it has chattering prevention circuit. JP36 SW_NMI JP37... -
Page 18: Volume
Volume It can output variable voltage (0V-IO voltage) to A/D terminal of CPU by variable resistor of 10KΩ. JP38 JP38 AP0_0/ADCA0I0 AP0_1/ADCA0I1 AP0_2/ADCA0I2 AP0_3/ADCA0I3 AP0_4/ADCA0I4 9-10 AP0_5/ADCA0I5 11-12 AP0_6/ADCA0I6 13-14 AP0_7/ADCA0I7 15-16 - 18 -... -
Page 19: Power
Power Connect bundled AC adapter (+5V) to AC Jack. You do not need to connect to the AC Jack on the CPU board. It generates the power of +12Ｖ for FlexRay driver and +3.3Ｖ for Ethernet PHY chip power from this power supply with using regulator. JP2 : 5V AC Jack JP3 : 3.3V... -
Page 20: Cpu Board
CPU Board One of "EB-850/F1L-100" or "EB-850/F1L-100-S" is mounted on the CPU board Switch & LED Reset Switch Debug Connector Filter Power Clock - 20 -... -
Page 21: Power
2.9.1 Power There is a jumper pin for measuring the current when you use only CPU board itself. CN4 : AC Jack Select Note Connect ammeter to check the current Short Operation voltage is 5V. Operation voltage is 3.3V. (Only when FL-BASE board is connected) 2.9.2 CPU CPU is direct-mounted for "EB-850/F1L-100". -
Page 22: Clock
2.9.3 Clock For the X1 and X2 of the CPU, 8MHz crystal oscillator (Y1) is mounted on the socket. 2.9.4 Reset CPU can be reset by pressing the Reset switch (SW2). The method of outputting reset on the FL-BASE board can be set with the jumper. Select Note Reset Switch(SW2) -
Page 23: Switch & Led
2.9.5 Switch & LED They are connected to port terminals of the CPU. LED1 LED2 LED3 LED4 Power LED ・ P8_1, P8_2, and P8_3 can be used for the switch inputs. It connects the pull-up resistor with built-in CPU. Set the switch to OFF to read High and to ON to read Low. -
Page 24: Debug Connector
2.9.6 Debug Connector "PG-FP5" of "E1 emulator" corresponding to Low Pin Debug Interface (4-pin) or a flash programmer is connectable with CN3. CN5 can connect the emulator corresponding to Low Pin Debug Interface (1-pin). (Unevaluated) Signal Number Debugger Writer DCUTCK JP0_2 ←... -
Page 25: Filter Socket
2.9.7 Filter socket Filters can be implemented to A/D input terminals. Connects (CN1, CN2) are connected through the sockets as illustrated below. Therefore, please make sure you connect resistor between the socket 4pin and 5pin when you use A/D terminal. Socket Connector Socket... -
Page 26: Can
2.9.8 CAN Please refer to 2.1 CAN. - 26 -... -
Page 27: Cpu Terminal Connection List
3 CPU Terminal Connection List Please download the Excel file from the web described in the document attached to the product. - 27 -...
Need help?
Do you have a question about the FL-850/F1L-100 and is the answer not in the manual?
Questions and answers