Advertisement
Table of Contents
HT/ST
1.2
(continued)
10
Assemble unit
'click'
backplate
12
Set up IQ Sensor types
It is recommended to use SET (software tool) for the setting of sensor type modules. For all IQ2
series controllers with firmware version 2.1 or greater, or IQ3 series controllers, the following SET
Unique Sensor References should be used:
Humidity:
Humidity I
Temperature:
Thermistor HTST DT (°C)
Thermistor HTST DT F (°F)
(change the values of U and L to +50 and -5 °C or +122 and +23 °F
respectively)
If not using SET, use the following tables for all IQ2 series controllers of firmware version 2.1 or greater
or IQ3 controllers; for all other IQ controllers see Sensor Scaling Reference Card TB100521A.
tYpe Sensor digI/P Driver Function loGic Loop scHedule seQnc Analog
digBit Knob sWitch Time Zone Oss User addRess intcoN calarM reView Plot
calEndar
= ?
Humidity (0 to 100 %RH)
Current
Y
n I
p
u
t t
p y
e
2
c (
u
r r
m
) A
Yx<CR>
E
E
p x
o
n
e
t n
3
TYPE x
U
U
p
p
r e
1
0
0
:
=?
L
L
o
w
r e
0
S=5 (characterise )
P
P
o
n i
s t
2
Y=, E=, U=, L=, P=
x
x I
O
x
I1 to I2=, O1 to O2=
1
4
0
X <CR>
2
2
0
1
0
0
13
Test system
Temperature
Δ T
14
2
1 - 4
HT/ST Space Humidity and Temperature Sensor Installation Instructions TG200921 Issue 1/B 30/08/06
Installation Instructions - Sheet 1
11
Configure IQ
IQ
or
IQ
IQ Configuration
Manual 90-1533
Temperature (0 to +40 °C)
Thermistor
U
i n
s t
°
C
F °
Yn<CR>
Y
1
(
h t
r e
m
t s i
r o
o v
t l
) s
n I
p
t u
y t
p
e
TYPE n
3
E
E
x
p
o
n
e
t n
:
5
0
1
2
2
U
U
p
p
r e
=?
S=5 (characterise)
L
5 -
2
3
L
o
w
r e
Y=, E=, U=, L=, P=,
P
P
o
n i
s t
6
I1 to I6=, O1 to O6=
x
x I
O
x
° (
C
)
O
x
° (
) F
X <CR>
1
2
6 .
4
1
5
0
1
2
2
2
3
4 .
7
4
0
1
0
4
3
4
4 .
6
3
0
8
6
4
6
6 .
6
3
1
0
5
0
5
7
6 .
6
8
0
3
2
6
8
1 .
0
2
5 -
2
3
Humidity
Δ H
HT/ST Installation Instructions - sheet 2
Space Humidity and Temperature Sensor
A4 double sided folded
Important: Retain these instructions
Contents
1.1
Unpacking ........................................ 1 - 1
1.1
Unpacking
1.2
Installation
1
Dimensions
2
Requirements
a
d
HT/ST Space Humidity and Temperature Sensor Installation Instructions TG200921 Issue 1/B 30/08/06
Installation Instructions - Sheet 1
1
1.2
Installation ........................................ 1 - 1
2.1
Maintenance ..................................... 2 - 1
2-2
Disposal ........................................... 2 - 3
86 mm (3.39")
26 mm (1.02")
> 50 cm (20")
b
1.5 m
(5 ft)
f
e
HT/ST
HT/ST Installation
Instructions TG200921
Sheet 1
Sheet 2
c
g
1 - 1
Advertisement
Table of Contents
Summary of Contents for TREND HT series
- Page 1 HT/ST Installation Instructions - Sheet 1 Installation Instructions - Sheet 1 Installation HT/ST (continued) Space Humidity and Temperature Sensor Assemble unit Configure IQ A4 double sided folded ‘click’ Important: Retain these instructions backplate IQ Configuration Installation ........1 - 1 Contents Manual 90-1533 Maintenance ........
- Page 2 HT/ST Installation Instructions - Sheet 1 Installation Instructions - Sheet 1 HT/ST Installation Installation (continued) (continued) Requirements (continued) Remove cutout(s) Route cables +60 °C as required -20 °C (140 °F) (-4 °F) +40 °C measurement 0 °C (32 °F) (104 °F) 0 %RH 100 %RH non -condensing...
- Page 3 Bois 37,Switzerland by its Authorized Representative, Trend Control Systems Limited. Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation to notify any person of such revisions or changes.
- Page 4 HT/ST Installation Instructions - Sheet 2 Installation Instructions - Sheet 2 HT/ST Maintenance Disposal (continued) WEEE Directive : Install new sensor tip At the end of their useful life the packaging hold sides of sensor and product should be disposed of by a suitable recycling centre.
Need help?
Do you have a question about the HT series and is the answer not in the manual?
Questions and answers