Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Audio A10-RX-XLR
Summary of Contents for Audio A10-RX-XLR
- Page 1 A10-RX Digital Wireless Receiver — — User Guide Models: A10-RX-SL and A10-RX-XLR...
-
Page 2: Table Of Contents
At the Receiver . . . . . . . . . . . . . . 4 A10-RX-XLR . . . . . . . . . . . . . . . 12 Connectors, Controls Description . -
Page 3: Overview
A10 system. It is designed to work with one or two A10-TX transmitters. It offers 224 MHz switching bandwidth and precision RF tracking filters in a lightweight, robust package. Two models are available, the A10-RX-SL for slot-in connection and the A10-RX-XLR for stand-alone operation with hardwired power and audio connections... -
Page 4: System Quickstart
3 Using the scanning tool in the Selection menu find an available open frequency. If multiple wireless systems are in use, make certain to keep frequencies least 400 kHz apart. 4 Connect the audio output from channel 1, channel 2, or both to an audio input on a mixer, recorder, camera, or PA system... -
Page 5: Connectors, Controls Description
A10-RX User Guide Connectors, Controls Description Figure 1: A10-RX 1 -Antenna Socket 4 -Left Button SMA connector, 50 ohm, connects to includ- Moves the selection in menu to the left, or ed 1/4-wave whip antenna decrements values 2 -Channel Power LED 5 -Menu/Select Button Illuminates blue when the channel’s receiver Enters the menu selection Also used to select... -
Page 6: Powering
A10-RX User Guide Powering The A10-RX-SL receives power over its D-sub connector The A10-RX-XLR receives power from its 4-pin Hirose female connector The male Hirose connector is a power loop through When DC power is present, either at the D-sub connector or the Hirose 4-pin, the A10-RX is... -
Page 7: Main Display
When the receiver is first powered on, the main display is in two-channel view. Two-Channel View The display shows channel 1 and channel 2 simultaneously Parameters displayed include the RF signal strength at each antenna, receiver frequency, audio level, and transmitter battery level. 1 -Channel 1 Settings 4 -Audio Level... -
Page 8: Rf Signal Indicator Leds
• Flashing Red - warns that the RF level is low and that the receiving error rate is high, possi- bly resulting in audio dropouts • Solid Red - when RF level no longer is suitable or when RF transmitter has been turned off. -
Page 9: Outputs Sub-Menu
Selects the polarity of the balanced output signal Channel • Normal • Inverted Mode Chooses the audio output type of the A10-RX Global • Analogue When the A10-RX is set to AES the channel 2 XLR • AES connection is not used... -
Page 10: System Sub-Menu
A10-RX User Guide System Sub-Menu ª All settings are Global. Selections Icon Description Options Exit Returns the main menu Power • 1 - channel 1 only Turns power to the RF receiver for each of the two channels on and off. •... -
Page 11: Frequency Scanning
Analogue Output When set to analogue in the Selection Menu the A10-RX outputs low-impedance, balanced line level audio It is designed to connect to balanced or unbalanced line level inputs To un- balance the output, float pin-3. AES Digital Output... -
Page 12: Antennae
1/2-wave distance of the transmitted frequency. Firmware Updates From time to time Audio Ltd. issues new firmware for the A10-RX receiver. Make certain to reg- ister your Audio Ltd. product at the Audio Ltd. website to receive firmware update notifications. - Page 13 A10-RX User Guide 2 Remove the A-SL accessory 3 Position the A-XLR accordingly, and replace screws ª Complete the above procedure in reverse to convert from A10-RX-XLR to A10-RX-SL. - 13 -...
-
Page 14: Specifications
Transmitters are tunable in 25 kHz steps Modulation Mode Audio Ltd proprietary digital RF modulation Digital Audio Codec Audio Ltd proprietary, high-performance digital encoding algorithm Audio Frequency Response 20 Hz–20 kHz Maximum Output Level +14 dBu, +2 dBu, -10 dBu, or -22 dBu, menu-selectable, with a 0 dBFS signal at the transmitter... -
Page 15: A10-Rx-Sl Db-25 Connector Pin Assignments
Ch 2 AES3+ (balanced, 110 ohm, transformerless) Ch 1 - analogue / Ch 1,2 Ch 1 - analogue audio out, +2 dBu level (+/- 0 5 dB), balanced Alternately, Ch 1 AES - and Ch 2 AES3- (balanced, 110 ohm, transformerless) -
Page 16: Certifications
Warning! Any modifications or changes made to this device, unless explicitly approved by Audio Ltd. may invalidate the authorisation of this device. Operation of an unauthorised device is prohibited under Section 302 of the Communications act of 1934, as amended, and Subpart 1 of Part 2 of Chapter 47 of the Code of Federal Regulations. -
Page 17: Frequency Tables
A10-RX User Guide Frequency Tables The A10-TX offers preselected frequencies based on channels and sub channels. Three sets of frequencies are available based on either 6, 7, or 8 MHz channel bandwidth. Select the channel bandwidth based on the geographic region where the unit is operating X Frequencies (6 MHz Per TV Channel) The chart below shows all frequencies available for the A10 wireless system. -
Page 18: Y Frequencies (7 Mhz Per Tv Channel)
A10-RX User Guide Y Frequencies (7 MHz Per TV Channel) Sub Channels 485 3 485 7 486 1 486 3 486 7 487 1 487 3 487 7 488 1 488 3 488 7 489 1 489 3 489 7 490 1 490 3 490 7 492 3 492 7 493 1 493 3 493 7 494 1 494 3 494 7 495 1 495 3 495 7 496 1 496 3 496 7 497 1 497 3 497 7 499 3 499 7 500 1 500 5 500 7 501 1 501 3 501 7 502 1 502 5 502 7 503 1 503 3 503 7 504 1 504 5 504 7 506 3 506 7 507 1 507 5 507 9 508 3 508 3 508 7 509 1 509 5 509 9 510 3 510 3 510 7 511 1 511 5 511 9... -
Page 19: Z Frequencies (8 Mhz Per Tv Channel)
Australia and New Zealand Japan Taiwan China For further information, contact Audio Ltd or your local distributor Copyright © 2017 Audio Ltd. All rights reserved. | www.audioltd.com 7 Century Court, Tolpits Lane, Watford WD18 9RS, UK | info@audioltd.com - 19 -... - Page 20 A10-RX User Guide - 20 -...
Need help?
Do you have a question about the A10-RX-XLR and is the answer not in the manual?
Questions and answers