WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Toshiba shall not be liable for any damages, losses, expenses or costs, if any, incurred in connection with or as a result of use of any information or data provided...
Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances. Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities.
(1/4) SAFETY INSTRUCTION WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" INSTRUCTIONS BELOW. Safety Precaution WARNING: SERVICING SHOULD NOT BE ATTEMPTED BY ANYONE UNFAMILIAR WITH THE NECESSARY PRECAUTIONS ON THIS RECEIVER. THE FOLLOWING ARE THE NECESSARY PRECAUTIONS TO BE OBSERVED BEFORE SERVICING THIS CHASSIS.
(2/4) Always ensure that all internal wirings are in accordance before re-assembling the external casing after a repairing completed. Do not allow internal wiring to be pinched by cabinets, panels, etc. Any error in reassembly or wiring can result in electrical leakage, flame, etc., and may be hazardous.
(3/4) The potential at any point (TOUCH CURRENT) expressed as voltage does not exceed the following value: The part or contact of a TERMINAL is not HAZARDOUS LIVE if: a) The open-circuit voltage should not exceed 35 V (peak) a.c. or 60 V d.c. or, if a) is not met.
(4/4) Product Safety Notice Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
(1/13) SERVICE MODE ENTERING SERVICE MODE 1) Press button once on 2) Press button again and 3) While pressing the button, Remote Control. keep pressing. press button on TV set. SERVICE MENU Key Key Self Check...
(2/13) ADJUSTING ITEMS IN THE SERVICE MODE Special setting Item Value Purpose if the picture have "Vertical Line problem", Vertical Line Normal, Special user can use the "special setting" to improve this problem V Lock if the picture have "up-down jitter problem", Normal, Special user can use the "special setting"...
(3/13) A : These item are similar phenomenon. So please try both items. B : The picture have white horizontal flare or some portion lost horizontal synchronize (disarray). In this case please try to change “White tail” 1, 2, 3, or 4.Then please choose the best one. C : If the picture have horizontal jitter please try to change this “H Jitter”...
(4/13) SELF CHECK “Self Check” screen is shown by pressing “9” button on Remote Control during display of the Service mode adjustment menu. “Self Check” screen should not be erased by timeout. Self Check OSD TV Model 32P1300D_A_LGD Model ID 0x03 Boot Version 00000...
(5/13) Item Explanation /Data Format “Model name”+”_”+”Suffix(A or B)”+”_”+”Panel vender” e.g. 32P1300D_A_LGD Model name : 29P1300D, 32P1300D TV Model Suffix: Panel vender : LGD:LGD , CMI:CMI Model ID Model ID indicating panel size and vender Display 1 byte data.(Hex) Boot Version Version information of boot code.
(6/13) MODEL ID TABLE Model Inch & Vendor Model Name in Self Check OSD 0x00 Not used 0x01 29P1300_CMI 29P1300_A_CMI 29P1300D_CMI 29P1300D_A_CMI 0x02 Reserved 0x03 32P1300_LGD 32P1300_A_LGD 0x04 32P1300_LGD 32P1300_A_LGD 32P1300D_LGD 32P1300D_A_LGD 0x05 32P1300_AUO(TBD) 32P1300_A_AUO 0x06 32P1300_CMI(TBD) 32P1300_A_CMI 0x07 Reserved 0x08 24P1300_CMI 24P1300_A_CMI...
(7/13) ENTERING HOTEL MODE MENU Hotel Mode Menu should be shown by the following operation. 1) Press button once on the 2) Press button again and 3) While pressing the button, Remote Control. keep pressing. press “+” button on TV set. Hotel Mode Settings Menu DISPLAY OF HOTEL MODE MENU - The Hotel Mode Menu should always be shown in English regardless of the Menu Language setting.
(8/13) Factory Item Options Description settings Hotel Mode Disable Hotel Mode. All the settings of Hotel Mode are disabled. Enable Hotel Mode Control Panel Allow use of all Control panel buttons Prohibit use of all control panel buttons. But, Power Off -> On by control panel POWER button is not prohibited.
(9/13) Change TV Tunes to the last channel or input viewed when POS/VIDEO powered on TV tunes to preset “POS/VIDEO” (channel or input) when TV is powered on. On (AC) TV tunes to preset “POS/VIDEO” (channel or input) only when AC power is applied. When TV is powered on by power button, tune to the last channel or input.
(10/13) RESETTING HOTEL MODE SETTINGS - Hotel Mode settings should be reset by special remote code for Factory Ship out. (Default values will be restored) - Hotel Mode settings should NOT be reset by “Reset TV” on the SETUP menu. (To prevent users from cancelling Hotel Menu settings that has been specially set by the hotel) CLONING HOTEL MODE SETTINGS - Hotel Mode settings should be copied to other TV by HOTEL CLONE function.
(11/13) 5) Insert USB Drive and press OK to copy settings to the USB drive. 6) Wait for window that indicates the copying process is complete before removing the USB drive. COPYING HOTEL MODE SETTINGS FROM USB DRIVE TO TV 1) Access the Hotel Clone menu using steps a-c.
(12/13) Note: If TV status is “out of Box“ condition, when turn on the TV first, “Quick Setup“ screen will be displayed. Before copying data to TV from USB by using Hotel Clone function, it is necessary to execute Auto Tuning for the purpose of disappearing the “Quick Setup“...
(13/13) TV SOFTWARE UPGRADE Steps to Upgrade TV-Microcomputer Software via USB Flash Memory. 1) Unplug the TV. 2) Prepare a USB device which contains the software update. 3) Insert the USB device into the USB terminal of the TV. 4) Plug in TV and watch LED on the front of the set. 5) You can see Orange LED on TV during updating.
When the panel version is updated within the same panel vendor, the last digit will be incremented by 1. Model/Panel Information Model SET ID Panel Panel ID 29P1300D V290BJ1-PE1 (Open Cell, CMI) 32P1300D LC320DXJ-SFE1 (Open Cell, LG) V390HJ1-P02 (Open Cell, CMI) 39P2300D T390HVN04.0 SKD (Open Cell, AUO)