Radio Shack 42-4058 Owner's Manual page 36

Stereo This is a cross feedback delay of stereo input
21
Delay 2 and output.
22 3-Tap Delay This is left/center/right 3-tap delay.
Gate This is a fader that creates artificial reverb that
23
Reverb sounds like it is being cut with a gate.
Reverse
This is gate reverb with a reverse rotation
24 Gate
effect.
Reverb
This is an effector that extracts the first reflected
25 Reflection
sound from a reverb sound.
This is a flanger in accordance with a sine wave
26 Reflection
LFO.
This is an effector that preserves the breadth of
27 Reverb
a sound by adding a reverb sound.
28 2-Tap Delay This is left/right 2 tap delay.
36
0: Delay Time (0 to 127) – Adjusts the delay time.
1: Wet Level (0 to 127) – Adjusts the level of the effect sound.
2: Feedback (0 to 127) – Adjusts the repeat of the delay.
3: High Damp (0 to 127) – Adjusts damping of the high-range delay sound. The
smaller the value, the greater the damping of high-range delay sound.
4: Ratio L (0 to 127) – Adjusts the delay time of the left channel, proportional to
the value set for Delay Time.
5: Ratio R (0 to 127) – Adjusts the delay time of the right channel, proportional to
the value set for Delay Time.
0: Delay Time (0 to 127) – Adjusts the delay time.
1: Wet Level (0 to 127) – Adjusts the level of the effect sound.
2: Feedback (0 to 127) – Adjusts the repeat of the delay.
3: High Damp (0 to 127) – Adjusts damping of the high-range delay sound. The
smaller the value, the greater the damping of high-range delay sound.
4: Ratio L (0 to 127) – Adjusts the delay time of the left channel. Proportional to
the value set for Delay Time.
5: Ratio C (0 to 127) – Adjusts the delay time of the center channel. Proportional
to the value set for Delay Time.
6: Ratio R (0 to 127) – Adjusts the delay time of the right channel. Proportional to
the value set for Delay Time.
0: LPF (0 to 127) – Adjusts the cutoff frequency of the low-pass filter. A smaller
value cuts the high range.
1: HPF (0 to 127) – Adjusts the cutoff frequency of the high-pass filter. A larger
value cuts the low range.
2: Feedback (0 to 127) – Adjusts the repeat of the reverb.
3: High Damp (0 to 127) – Adjusts damping of the high-range delay sound. The
smaller the value, the greater the damping of high-range delay sound.
4: Diffusion (0 to 127) Provides fine adjustment of the reverb.
5: Wet Level (0 to 127) – Adjusts the level of the effect sound.
6: Dry Level (0 to 127) – Adjusts the level of the original sound.
0: LPF (0 to 127) – Adjusts the cutoff frequency of the low-pass filter. A smaller
value cuts the high range.
1: HPF (0 to 127) – Adjusts the cutoff frequency of the high-pass filter. A larger
value cuts the low range.
2: Feedback (0 to 127) – Adjusts the repeat of the reverb.
3: High Damp (0 to 127) – Adjusts damping of the high-range reverb sound. The
smaller the value, the greater the damping of high-range reverb sound.
4: Diffusion (0 to 127) Provides fine adjustment of the reverb.
5: Wet Level (0 to 127) – Adjusts the level of the effect sound.
6: Dry Level (0 to 127) – Adjusts the level of the original sound.
0: Type (0 to 7) Selects from among the eight available reflection patterns.
1: Wet Level (0 to 127) – Adjusts the level of the effect sound.
2: Feedback (0 to 127) – Adjusts the repeat of the reflected sound.
3: Tone (0 to 127) – Adjusts the tone of the reflected sound.
0: LFO Rate (0 to 127) – Adjusts the rate of the LFO.
1: LFO Depth (0 to 127) – Adjusts the depth of the LFO.
2: Feedback (-64 to +63) – Adjusts the feedback of the sound.
3: Wet Level (0 to 127) – Adjusts the level of the effect sound.
0: Tone (0 to 127) – Adjusts the tone of the reverb sound.
1: Time (0 to 127) – Adjusts the reverb time.
2: High Damp (0 to 127) – Adjusts damping of the high-range reverb sound. The
smaller the value, the greater the damping of high-range reverb sound.
3: ER Level (0 to 127) – Adjusts the level of the initial reflection.
4: Wet Level (0 to 127) – Adjusts the level of the effect sound.
0: Delay Time (0 to 127) – Adjusts the delay time.
1: Wet Level (0 to 127) – Adjusts the level of the effect sound.
2: Feedback (0 to 127) – Adjusts the repeat of the delay.
3: High Damp (0 to 127) – Adjusts damping of the high-range delay sound. The
smaller the value, the greater the damping of high-range delay sound.
4: Ratio L (0 to 127) – Adjusts the delay time of the left channel, proportional to
the value set for Delay Time.
5: Ratio R (0 to 127) – Adjusts the delay time of the right channel, proportional to
the value set for Delay Time.