Preparation For Use; Turn On The Unit For The First Time; Clock Setup - Presidian DVD / VCR Owner's Manual

Preparation for Use

Turn on the Unit for the First
Time
VCR VCR
VCR VCR VCR
1
1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see"RF Output Channel" section on page 6.
• If your antenna is connected to an antenna ampli-
fier, the amplifier's gain adjustment may need to
be temporarily reduced in order for Auto-Setup to
program all channels properly.
2
2
POWER
Remote Control TV Screen
LANGUAGE SELECT
ENGLISH
FRANCAIS
ESPAÑOL
or
3
3
AUTO SET UP
Do you connect the cable from the cable box or
the satellite box to the unit's ANT-IN jack?
YES
Y es
Y es
Press [MENU]
to exit.
• Refer to "Hint for Cable Box or
Satellite Box" section on page 6.
No
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized channel.
• You can select only the channels memorized
in this unit by using [SKIP/CH.
(or [CHANNEL / ]).
• If "AUTO SET UP" appears on the TV
screen again, check the cable connections.
Then, press [ ] once again.
Hint
Hint
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
To Select a Channel
You can select a channel by using
the Number buttons or
.
[SKIP/CH. / / ]
Notes for using the Number buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number. (For
example: 117, press [1], [1], [7])
• You must precede single-digit chan-
nel numbers with a zero (for example:
02, 03, 04 and so on).
To Add or Delete Channels
1) Press [MENU] until the main menu
appears.
2) Select "CHANNEL SET UP" by
pressing [ / ]. Then, press [ ].
3) Select "MANUAL SET UP" by
pressing [ / ]. Then, press [ ].
4) Enter the desired channel number by
pressing [ / ] or
[SKIP/CH.
5) Add or Delete it from memory by
pressing [ / ] so that "ADD" or
"DELETE" flashes on the TV screen
accordingly.
6) Exit the Preset mode by pressing
[CLEAR/C.RESET].
To Preset the Channel Again
1) Press [MENU] until the main menu appears.
[ON]
2) Select "CHANNEL SET UP" by pressing
[ / ], then press [ ].
3) Select "AUTO SET UP" by using [ / ],
then press [ ]. After scanning, the tuner
stops on the lowest memorized channel.
To Change the On-Screen Language
1) Press [MENU] until the main menu appears.
2) Select "LANGUAGE SELECT" by pressing
[ / ], then press [ ].
CH 01
3) Select "ENGLISH" , "FRANCAIS" or
"ESPAÑOL" by pressing [ / ] , then press
[CLEAR/C.RESET] to exit.
Hint
Hint
• If you accidentally select Spanish or French
and need English: Press [MENU] and
choose SELEC. IDIOMA or SELECTION
LANGUE. Press [ ] and select ENGLISH.
Finally, press [CLEAR/C.RESET].
• To add or delete channels in this unit,
[SKIP/CH. /
the channel number memorized in this
unit, [ / ] works on all.
NO

Clock Setup

VCR VCR
VCR VCR VCR
1
1
MENU
/ / ]
or
2
2
or
3
3
/ / ].
4
4
5
5
6
6
/ ] button works on
7
7
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
8
8
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
• If the clock is not set, the
CLOCK SET screen
appears when you press
[MENU]. In this case, go
to step 2).
Hint
Hint
• To go back one step, press [ ] (during
• Your clock setting will be lost if either there
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current month.
– 8 –
CLOCK SET
MONTH DAY
1 0 / 0 2
or
HOUR MINUTE
– – : – –
Select the current day.
CLOCK SET
MONTH DAY
or 1 0 / 0 2
HOUR MINUTE
– – : – –
Select the current year.
CLOCK SET
MONTH DAY
or
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE
0 5 : – –
Select the current hour.
CLOCK SET
MONTH DAY
or
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE
0 5 : 4 0
Select the current minute.
CLOCK SET
MONTH DAY
1 0 / 0 2 MON 2 0 0 6
or
HOUR MINUTE
0 5 : 4 0
Select "AM" or "PM".
To exit the CLOCK SET
screen
steps 2) to 7) ).
is a power failure or this unit has been
unplugged for more than 30 seconds.
YEAR
– – – –
AM/PM
– –
YEAR
2 0 0 6
AM/PM
– –
YEAR
AM/PM
– –
YEAR
AM/PM
– –
YEAR
AM/PM
P M AM
PM
EN