Page 2
All rights reserved September 7, 2007. The information in this document is proprietary to Redline Communications Inc. This document may not in whole or in part be copied, reproduced, or reduced to any medium without prior consent, in writing, from Redline Communications Incorporated.
Page 5
SU-O User Manual LIST OF FIGURES Figure 1: Notices - WEEE Logo ................12 Figure 2: Intro - RedMAX Subscriber Outdoor System ........14 Figure 3: System - PTP Line of Sight Deployment..........16 Figure 4: System - Fresnel Zone................. 17 Figure 5: System - Non-Line of Sight Deployment ..........
Page 11
Redline Communications declara que este subscriber está conforme com os requisitos essenciais e outras provisões da Directiva 1999/5/CE. Spanish Por medio de la presente Redline Communications declara que el subscriber cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE Swedish Härmed intygar Redline Communications att denna subscriber står I...
Figure 1: Notices - WEEE Logo In accordance with the WEEE (Waste from Electrical and Electronic Equipment) directive, 2002/96/EC, Redline Communications equipment is marked with the logo shown above. The WEEE directive seeks to increase recycling and re-use of electrical and electronic equipment.
Chapter Congratulations on your purchase of the Redline WiMAX Forum Certified™ subscriber wireless broadband product. Redline Communications is a world leader in design and production of WiMAX and proprietary Broadband Fixed Wireless (BFW) systems. The outdoor subscriber is carrier class high-speed IEEE 802.16-2004 WiMAX compliant for point-to-point (PTP) and point-to-multipoint (PMP) deployment.
(PHY) layers. Note that the 802.16-2004 standards are subject to amendment, and the subscriber product design compliance applies to a specific revision of the standard. The RedMAX product does not support mesh communication, but does support subscriber-to-subscriber communication using TLS.
VLAN tag. All classification is defined at the base station and the classification parameters are downloaded to the subscriber. RedMAX supports service flows with different classification types including: 802.3 Ethernet, 802.1Q VLAN, IPV4, IPV4 Over 802.3 and IPV4 Over 802.1Q -- with options to classify based on Source and Dest of MAC and IP addresses, VLAN tag and Vlan priority, Src and Dst port number, TOS Value and Ethernet protocol type.
™ Subscriber Modem SU-O User Manual Chapter The RedMAX subscriber can be deployed with an integrated antenna or an external antenna. Integrated Antenna (SU-OIA) This subscriber with integrated antenna consists of an outdoor radio (transceiver and antenna) and an indoor power-block with network connections. The subscriber electronics are housed in a weatherproof aluminum alloy case.
™ Subscriber Modem SU-O User Manual Mounting the Outdoor Subscriber Refer to the RedMAX Installation Guide (P/N: 70-00059) for detailed instructions. 3.4.1 Outdoor Subscriber with Integrated Antenna The SU-OIA has an integrated flat panel antenna. The vertical mount bracket can accommodate a flat vertical surface or 2.45 - 11.45 cm (1 - 4 ½...
1 -- Full. managedSS The managedSS command allows you to configure the subscriber for independent operation, or enable management using the RedMAX EMS system. The managedSS parameter is controlled from root mode. The following table lists all commands available for managedSS.
Actual Ethernet data throughput is dependent on channel size, protocols, packet size, burst rate, transmission latency, and link distance. Receive Sensitivity The following table lists the RedMAX subscriber sensitivity levels for different modulation and coding levels. Table 25: Reference - RedMAX Subscriber Receive Sensitivity...
The subscribers must be updated using CLI while the base station may be updated using CLI or the Web interface. If available, you may use the RedMAX RMS server provisioning features to upgrade the RedMAX software. All upgrades require an FTP server.