Summary of Contents for Magellan MHI1-548
- Page 1 HYBRID SERIES USER MANUAL HYBRID INVERTER agellan Powertronics Pty.Ltd 64 bushland Ridge Bibra Lak e,Perth Western Australia,6148 support@magellan-power .com.au Worldwide +61 89434 6621 Fax +61 89 434 6623...
-
Page 2: Installation
1 Introduction ..................01 2 Important Safety Warning 2.1 Symbols ..........01 2.2 Safety ..........02 3.1 Packing List ........03 3 Installation 3.2 Product Overview ........ 03 3.3 Selecting The Mounting Location ..... 04 3.4 Mounting .. -
Page 3: Important Safety Warning
Let it cool before touching it. The hybrid series inverter of Magellan Powertronics Pty Ltd. (hereinafter referred to as Magellan) strictly conforms to related safety ● Ensure children are kept away from inverters. -
Page 4: Packing List
3 Installation 3.3 Selecting The Mounting Location 3.1 Packing List Mounting location should be selected based on the following aspects: ● The installation method and mounting location must be suitable for the inverter's weight and dimensions. Before installation, please inspect the unit. Be sure that nothing inside the package is damaged. You should have received the ●... -
Page 5: Electrical Connection
Please follow below steps to implement AC connection: 3.4 Mounting (1) Check the grid voltage and frequency at the connection point of the inverter. It should meet Magellan product Spec. Remember that this inverter is heavy! Please be carefully when lifting out from the package. -
Page 6: Battery Connection
48V. 2.5~4mm Please follow below steps to implement battery connection: (1) Check the nominal voltage of batteries. The nominal output voltage should meet Magellan product Spec. 2.5~4mm (2) Disconnect DC breaker between inverter and battery. Negative plug (3) Disconnect screw cap from insulator. -
Page 7: Communication Connection
RS-485 cover Cable Waterproof ring Crystal head - ---- black cable red cable + ---- Screw cap Insulator Cable core section after crimp Positive Negative terminal terminal (red) (black) Color Function Color Function Orange/white RESERVED Orange/white 485A RESERVED 485B Orange Orange RS-485 Figure 4... -
Page 8: System Connection Diagram
4.6 Wi-Fi Connection Figure 4 Install the antenna to inverter. Refer to Figure 4.7-1. 4.9 System Connection Diagram Switch Board Back-Up Loads Back-Up Battery RS-485 Magellan Figure 4.7-1 Hybrid Inverter Solar Main array Switch HESS 4.7 Wi-Fi Reset & Reload Grid... -
Page 9: Led Lights Illustration
5 LED Lights Illustration 4.10 Processing method of battery connect multiple inverters SYSTEM BACK-UP SOLAR BATTERY GRID ENERGY FAULT Green Green ellow ellow HESS Meter INDICATOR STATUS EXPLANATION HESS Meter ON = SYSTEM IS READY BLINK = SYSTEM IS STARTING UP SYSTEM OFF = SYSTEM IS NOT OPERATING HESS Meter... -
Page 10: Work Modes
8 Error Messages 7. Work Modes An error message will be displayed on the APP if a fault occurs. Hybrid series inverters have the following main work modes based on different conditions: Table 8-1 is the Description of Error Message Error message Description Utility Loss... -
Page 11: Technical Parameters
9 Technical Parameters Model MHI1-548 99.9% MPPT adaptation efficiency Model MHI1-548 Protection Solar Integrated Residual current monitoring unit Max. allowed PV Power (W) 6000 Integrated Anti-islanding protection Nominal DC power (W) 5400 Integrated (optional) DC switch(PV) Max. DC voltage (V) - Page 12 Note Overvoltage category definition Category I : applies to equipment connected to a circuit where measures have been taken to reduce transient overvoltage to a low level. Category II : applies to equipment not permanently connected to the installation. Examples are appliances, portable tools and other plug-connected equipment;...