DEGEN BBQ 101520 Installatioin Manual

Baby boomer quads series

Hide thumbs

(includes BBQ 101520, BBQ 10, BBQ 15 and BBQ 20

includes BBQ 101520, BBQ 10, BBQ 15 and BBQ 20 )

DANGER:

ASSEMBLING

SEMBLING

The BBQ101520 can be assembled and erected by one person. The help of a second does

make the job easier. No stringing of wires is required as the antenna is pre-tuned and pre

make the job easier. No stringing of wires is required as the antenna is pre

strung.

1.1.

PARTS LIST

1 pc. Driven Element (Folded)

1 pc. Reflector Element (Folded)

1 pc. Boom

1 pc. Mounting Plate 2" mast.

1 bag Assembly (8 bolts, 8 lock washers,

(8 bolts, 8 lock washers, 4 spiral clamps for boom, 4 mounting plate

clamps)

1 bag Spare Parts (4 #8 1-1/2" bolts, 4

3/8 bolts, 4 3/8 lock waskers, 10 HD crimp eyelets, 1 spiral clamp, 1 boom clamp, 15ft

line, 20ft 14ga flexweave)

Installation Instructions

Baby Boomer Quads

It is the responsibility of the purchaser to ensure that all

It is the responsibility

required safety procedures are followed for erecting the

required safety procedures are follow

antenna. Avoid contact with overhead wires. Improper

antenna. Avoid contact with overh

erection can result in death or serious injury!

erection can result in death or serious injury

4 spiral clamps for boom, 4 mounting plate

1/2" bolts, 4 #8 5/8" bolts, 10 #8 lock washers, 10 #8 nuts, 2

#8 5/8" bolts, 10 #8 lock washers, 10 #8 nuts, 2

Page 1 of 8

to ensure that all

for erecting the

ead wires. Improper

tuned and pre-

Table of Contents

Need help?

Do you have a question about the BBQ 101520 and is the answer not in the manual?

Questions and answers

Summary of Contents for DEGEN BBQ 101520

Page 1 Installation Instructions Baby Boomer Quads (includes BBQ 101520, BBQ 10, BBQ 15 and BBQ 20 includes BBQ 101520, BBQ 10, BBQ 15 and BBQ 20 ) DANGER: It is the responsibility It is the responsibility of the purchaser to ensure that all...
Page 2 1.2. ASSEMBLY Remove all tie-down fasteners from the above mentioned pieces. Remove the mounting plate and store for later use. Remove boom and store for later use. Remove either element and stand upright as show in Fig 1. Fig. 1 Remove packing tape on wire prior to opening.
Page 3 Fig. 3 The antenna should lay flat. If it does not, check for tangled connections as shown in Fig. 4 and untangle. Fig.4 When antenna lays flat insert and tighten 4 bolts with lock washers as per Fig. 5 and Fig. 6. Page 3 of 8...
Page 4 Fig. 5 Fig.6 Page 4 of 8...
Page 5 Move section out of way to allow for assembly of second section. Fig. 7 Repeat steps 4 thru 9. Mount the mounting plate on the mast. Center and mount the boom on the mounting plate. Lift and mount one element on one end of the boom. Fig.8 Page 5 of 8...
Page 6 Fig. 9 Fig.10 Align element so that the interconnection point between Outer Loops and Capacity Hats are horizontal (feed point at bottom) Fig. 11 and Fig. 12. Fig.11 Page 6 of 8...
Page 7 Fig 12. Repeat steps 13 and 14 for second element. Align antenna to rotor system. The direction of transmission is from the reflector to the driven element (feed point). Attach and secure feed to antenna (DO NOT LET FEED HANG FROM ANTENNA FEED POINT).
Page 8 Warranty This limited warranty is extended to all end users of Degen Designs Antenna. Your product is warranted to be free from defects in manufacturing, materials and workmanship. If such defect appears during the term of the warranty Degen Designs will repair or replace the defective material at Degen Designs discretion.

This manual is also suitable for:

Bbq 10Bbq 15Bbq 20