Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for d&b audiotechnik DS100
Summary of Contents for d&b audiotechnik DS100
- Page 1 DS100 Manual 1.3 en...
- Page 2 General information DS100 Manual Version: 1.3 en, 02/2018, D2034.EN .01 Copyright © 2018 by d&b audiotechnik GmbH; all rights reserved. Keep this manual with the product or in a safe place so that it is available for future reference. We recommend you to regularly check the d&b website for the latest version of this manual.
-
Page 3: Table Of Contents
Basic setup................17 Service/Maintenance and care........18 7.1. Service..................18 7.2. Maintenance and care............18 Manufacturer's Declarations........19 8.1. EU declaration of conformity (CE symbol)......19 8.2. WEEE Declaration (Disposal)..........19 8.3. Licenses and Copyright............19 d&b DS100 Manual 1.3 en... -
Page 4: Scope Of Supply
IEC Std.** IEC Std.** IEC Std.** IEC Std.** *Mains plug types and associated standards / **IEC type IEC Lock: Lockable IEC plug IEC Std.: Standard IEC plug (Illustrations are approximations only and not true to scale) d&b DS100 Manual 1.3 en... -
Page 5: Ds100 Signal Engine
2. DS100 Signal Engine 2.1. Intended use The d&b DS100 Signal Engine is a specialized 3 RU, 19" rack mount audio processor with Audinate Dante audio networking. In its base configuration, it provides a 64 x 64 level / delay audio matrix. -
Page 6: Technical Specifications
Up to 144 USB 3.0 port Impulse response length Up to 10 seconds Controls and indicators Mains power switch Rocker switch on rear panel POWER Push-button switch with integrated ring-LED indicator Boot time Appr.: 45 sec. d&b DS100 Manual 1.3 en... - Page 7 DS100 dimensions in mm [inch] d&b DS100 Manual 1.3 en...
-
Page 8: Startup
Refer to Þ Chapter 4.4.2. "POWER power switch" on page 12. "ETHERNET indicators" on page 13 button and indicator" on page 12. AUDIO NETWORK indicators Refer to Þ Chapter 4.4.4. "AUDIO NETWORK indicators" on page 13. d&b DS100 Manual 1.3 en... -
Page 9: Rack Mounting And Cooling
6" is usually sufficient) to accommodate the cables and connectors at the rear of the device. When mounting the DS100 into a 19" rack, do not just rely on fixing and supporting the device by its front panel using appropriate rack mounting screws and U washers as shown in the graphic opposite. -
Page 10: Connections
Lockable IEC type mains plug (IEC Lock) Once the mains plug is connected, it is locked to avoid accidental disconnection of the device. To disconnect the power cord, pull the release button [R] towards you and pull out the mains plug. d&b DS100 Manual 1.3 en... -
Page 11: Ethernet
Ethernet. 4.3.3. USB An USB 3.0 port [3] is provided for future functionality. 4.3.4. AUDIO NETWORK The DS100 provides a fully supported Dante audio network interface [4] (Gigabit only). PRImary RJ45 Ethernet port (Primary): Used to connect the device to the primary Dante network to transmit and receive audio. -
Page 12: Controls And Indicators
Behavior after re- while device is: establishing AC power: Device powers up immediately: Þ Previous 'ON' state restored. Þ Device keeps 'ON' state. Device powers up immediately: Þ Previous 'OFF' state restored. Þ Device shuts down. d&b DS100 Manual 1.3 en... -
Page 13: Ethernet Indicators
If all LEDs illuminate red, this indicates that the Dante system has detected errors when booting and has entered failsafe mode. To restore a device that has entered failsafe mode, use the Dante Firmware Update Manager (available from the d&b website at www.dbaudio.com). d&b DS100 Manual 1.3 en... -
Page 14: Initial Setup
A Web Remote interface is integrated which provides direct access to the DS100 using a standard web browser. Note: The DS100 can only be accessed after connecting the device to a computer via Ethernet. However, this requires to manually set a static IP address on the PC network interface. -
Page 15: Web Remote Interface Page
2. Choose the desired option from the drop-down list and select «Save». Þ The event log data will be downloaded and the download progress will be displayed. Once the download is completed, a corresponding message will be displayed. d&b DS100 Manual 1.3 en... - Page 16 5.1.1.3. Licenses tab Apart from the serial number of the device (Þ «DS100 serial number»), the «Licenses» tab provides an overview of the licenses installed on the device (Þ «License status») and allows new licenses or license updates to be uploaded to the device (Þ...
-
Page 17: Basic Setup
6. Basic setup d&b DS100 Manual 1.3 en... -
Page 18: Service/Maintenance And Care
▪ the device was dropped or the housing is damaged. 7.2. Maintenance and care During normal operation, the device provides maintenance-free service. Due to the cooling concept, no dust filters are required. As a result, filter exchange or cleaning is not necessary. d&b DS100 Manual 1.3 en... -
Page 19: Manufacturer's Declarations
8.1. EU declaration of conformity (CE symbol) This declaration applies to: d&b DS100, Z4100 All products of type DS100 starting from variant Z4100 .000 are included, provided they correspond to the original technical version and have not been subject to any later design or electromechanical modifications. - Page 20 www.dbaudio.com...
Need help?
Do you have a question about the DS100 and is the answer not in the manual?
Questions and answers