Download Print this page

ABS Sanimat 1501S Installation And Operating Instructions Manual

Lifting station

Advertisement

Quick Links

ABS lifting station Sanimat
Installation and Operating Instructions
GB
www.absgroup.com

Advertisement

loading

Summary of Contents for ABS Sanimat 1501S

  • Page 1 ABS lifting station Sanimat Installation and Operating Instructions www.absgroup.com...
  • Page 2 Commentary on maintenance of Lifting Stations in accordance with EN 12056........14 General maintenance hints ........................15 Oil filling and Oil changing ........................15 Cleaning of level control pipe ........................ 15 ABS reserves the right to alter specifications due to technical developments...
  • Page 3: Nameplate

    ������������ ���� ���������� ������������ ABS lifting station Sanimat G������ 1.1 A���������� ����� These lifting stations may not be used for the collection or pumping of flammable or corrosive liquids. Effluent containing grease, petrol, or oil should only be brought to the lifting station via a separation device.
  • Page 4 ������������ ���� ���������� ������������ ABS lifting station Sanimat 1.4 D������ �f �h� f����� ��f����� ������� Figure 2 Design of the lifting station Discharge line Shut-off valve Ball-type non-return valve Inflow port DN 150/200, height 600 mm Motor connection cable Submersible pump Pump head support Flexible connector between collection tank and submersible pump - is noise absorbing...
  • Page 5: S�F��Y

    S�f��y The general and specific health and safety hints are described in detail in the separate booklet Safety Hints. If anything is not clear or you have any questions as to safety make certain to contact the manufacturer ABS. T��������...
  • Page 6 ������������ ���� ���������� ������������ ABS lifting station Sanimat M�������� ���� ������������ NOTE We recommend that original ABS installation accessories be used for mounting and installation of the unit Particular attention must be paid to the safety regulations covering work in closed areas as well as good general technical practices. Figure 3 Installation example L������� Vent Pipe (DN ≥70) above roof level...
  • Page 7 ������������ ���� ���������� ������������ ABS lifting station Sanimat 4.1 S��� ��q����m���� The rooms in which lifting stations are installed must be of adequate dimensions so that beside and over all control elements or items where maintenance might be required a working area of at least 60 cm width or height is available.
  • Page 8: Discharge Line

    ������������ ���� ���������� ������������ ABS lifting station Sanimat 4.3 �������� �f �h� ���������� ���k ����� ����� Only open inlet posts that are to be used. Saw off as little as possible so that as much material as possible is left for the plug connection. File down sharp edge inside and outside.
  • Page 9 ������������ ���� ���������� ������������ ABS lifting station Sanimat 4.5 ������������ �f �h� ��bm����b�� ��m� 4.5.1 M�������� �f �h� v����� ������� Figure 6 Mounting of volute support ATTENTION The area where the pump stands should be smooth and level. The distance from the centre line of the discharge port to the centre line of the discharge port comprises 460mm in the case of twin pumping stations. Fit flexible connection (8) with clamp (7) to the pump connection port of the collection tank (1). Press the volute support (6) into the flexible connector (8) and mark the position of the volute support (6) on the floor.
  • Page 10: Level Control

    ������������ ���� ���������� ������������ ABS lifting station Sanimat S�bm����b�� ��m�� AFP M15 ,M ,M30 , M40 ���� M60 Locate vibration damper (3) at the pump head support (2). Fit the pump head support through ”Eyelet A” at the pump head. Adjust the vibration damper (3) so that the rubber support rests on the ground and fix the vibration damper (3) in position using hex nuts and washers.
  • Page 11 ������������ ���� ���������� ������������ ABS lifting station Sanimat Control line (3) has a continuous rise as shown in Figure 9. The control line should be shortened where necessary, pushed on to the hose nozzle of the submerged tube screw connector (5). The submerged tube screw connector (5) is prevented from turning by using an open ended spanner SW 13 and a spigot nut (4) is fully tightened.
  • Page 12 ������������ ���� ���������� ������������ ABS lifting station Sanimat 4. W������ D������m Th��� Ph��� S������ Ph��� Figure 10 Three Phase Wiring Figure 11 Single Phase Wiring Figure 12 Three Phase Wiring with Temperature Limiter Figure 13 Single Phase Wiring with Temperature Limiter Figure 14 Three Phase Wiring with Temperature Limiter &...
  • Page 13 ������������ ���� ���������� ������������ ABS lifting station Sanimat 4.10 Ch��k���� ���������� �f �������� The safety hints in the previous sections must be observed! When three phase units are being commissioned for the first time and also when used on a new site, the direction of rotation must be carefully checked by a qualified person.
  • Page 14: Electrical Connection

    ������������ ���� ���������� ������������ ABS lifting station Sanimat C�mm���������� The safety hints in the previous sections must be observed! Before commissioning the unit should be checked and a functional test carried out. Particular attention should be paid to the following: Have the electrical connections been carried out in accordance with regulations?
  • Page 15 Should, nevertheless, a malfunction occur, do not improvise but ask your ABS customer service department for assistance.
  • Page 16 ABS Production Wexford Ltd., Clonard Road, Wexford, Ireland Tel. +353 53 91 63 200 Fax +353 53 91 42335. www.absgroup.com...

This manual is also suitable for:

Sanimat 3702s