1. Manuals
  2. Brands
  3. Magnum Manuals
  4. Sander
  5. MI-16150
  6. Operating manual

Magnum MI-16150 Operating Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL NO.: MI-16150
OPERATING MANUAL

Advertisement

Table of Contents
loading

Summary of Contents for Magnum MI-16150

  • Page 1 MODEL NO.: MI-16150 OPERATING MANUAL...

  • Page 2: Table Of Contents

    TABLE OF CONTNETS Table of contents ________________________________________________ Safety rules ____________________________________________________ Specifications __________________________________________________ Instructions for operations _________________________________________ Tilting the table _________________________________________________ Mounting spindle drum ___________________________________________ Selection guide for drum to table insert _______________________________ Maintenance of spindle sander _____________________________________ Troubleshooting _________________________________________________ Assembly diagram _______________________________________________ 10-14...

  • Page 3: Safety Rules

    SAFETY RULES Read carefully before operating the machine 1. Learn the machine’s applications and limitations, as well as the specific potential hazards particular to this machine. Follow available safety instructions and safety rules carefully. 2. Keep working area clean and be sure adequate lighting is available. 3.

  • Page 4: Specifications

    SPECIFICATIONS MODEL MI-16150 Table size (L x W) 616 x 616 mm Table tilt 0 ~ 45° Spindle speed 1725rpm Oscillations 59/min Oscillation stroke 39 mm Sanding sleeve length 150 ~ 230 mm Max. workpiece height 55 ~ 160 mm...

  • Page 5: Instructions For Operations

    INSTRUCTIONS FOR OPERATIONS 1. Select spindle that is smaller than the curve to be sanded. 2. Use an insert plate that comes closest to the spindle without touching it. 3. Make sure that spindle is properly positioned in taper sleeve socket. With the wrench provided , tighten the nut.

  • Page 6: Tilting The Table

    TILTING THE TABLE 1. Loosen the two table lock knobs (A), located under the table at both sides of the machine 2. Tilt the table forward to the desired angle with your hands. 3. An angle scale is provided at the right side of the trunnion to indicate the degree of table tilt. 4.

  • Page 7: Mounting Spindle Drum

    MOUNTING SPINDLE DRUM 1. Disconnect the sander from the power source. 2. Select the proper diameter of spindle drum. 3. Clean the taper part of the spindle drum before mounting it into the spindle. 4. Use an open-end wrench to lock the spindle by holding its flat surface. At the same time, use another open-end wrench to tighten the spindle drum.

  • Page 8: Selection Guide For Drum To Table Insert

    SELECTION GUIDE FOR DRUM TO TABLE INSERT This machine is furnished with 10 drums. The range of drum diameter is from 1/4” to 4”. If the drum diameter is changed, the table insert needs to be changed to the proper size. The table below shows which table insert to use for various drum diameters.

  • Page 9: Maintenance Of Spindle Sander

    MAINTENANCE OF SPINDLE SANDER 1. To keep spindle sander in perfect condition, clean machine and attachments at all times. 2. Clean tapered sleeves and tapered socket before use, this will protect spindle sleeves from nicks. 3. Bent sleeves are easily straightened by placing them in the tapered socket and slipping a small pipe over the steel shaft.

  • Page 10: Troubleshooting

    TROUBLESHOOTING TROUBLE CAUSES CORRECTION 1. Switch is burned out. Motor does not run when power 1. Replace the switch. 2. Connection wire is loose or switch is turned “ON”. 2. Tighten or replace the wire. damaged. 1. Power voltage is too low. 1.

  • Page 11: Assembly Diagram

    ASSEMBLY DIAGRAM...
  • Page 13 PARTS LIST FOR 16150 PART NO. REF. NO. DESCRIPTION MI16150-07 L0000000 POWER CORD MI16150-11 S0400525 MI16150-18 30101011 OIL INDICATOR MI16150-20 30101014 OIL SEAL MI16150-21 C1206206 BALL BEARING MI16150-22 S0530025 C SNAP RING MI16150-26 30103014 SLEEVE MI16150-27 30103015 GUIDE RAIL SHAFT MI16150-28 C1206205 BALL BEARING...
  • Page 14 PARTS LIST FOR 16150 PART NO. REF. NO. DESCRIPTION MI16150-109 30105069 WASHER MI16150-110 30105070 P.V.C 1" MI16150-111 30105071 SANDING CLOTH MI16150-112 30105072 WASHER MI16150-113 30105073 SANDING CLOTH MI16150-114 30105074 ARBOR MI16150-118 30105076 SANDING CLOTH MI16150-119 30105077 ARBOR MI16150-122 30105079 SANDING CLOTH MI16150-124 30105080 ARBOR...

  • Page 15: S0720302

    PARTS LIST FOR 16150 PART NO. REF. NO. DESCRIPTION MI16150-170 S0110600 MI16150-171 10401029 RUBBER FEET MI16150-172 S0030512 SINKING HEAD SCREW MI16150-173 S0110500 MI16150-175 S0050505A SET SCREW MI16150-176 30101002G-1 INDICATOR COVER MI16150-177 S0720302 RIVET MI16150-178 30101025Z TOOL HOOK MI16150-180 ALLEN WRENCH MI16150-181 RED STOP COVER...

Table of Contents