Download Print this page
Hide thumbs Also See for IN3924:

Advertisement

Quick Links

Declaration of Conformity
Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Suite 200, Portland, Oregon
97223-8368 USA
We declare under our sole responsibility that this projector conforms to the following
directives and norms:
ErP Directive 2009/125/EC
EMC Directive 2004/108/EC
EMC: EN 55024:2010, EN 55022:2010, EN 61000-3-2:2006+A1:2009+A2:2009,
EN 61000-3-3:2008
Low Voltage Directive 2006/95/EC
Safety: IEC 60950-1: 2005;EN 60950-1:2006 +A11:2009
R&TTE Directive: 1999/5/EC
ETSI: EN 300 440, EN 301 489
The receiver portion of this product is a Category III device, as specified in EN 300 440.
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple
Computer, Inc. IBM is a trademark or registered trademark of International Business
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered
trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered
trademarks of Adobe Systems Incorporated. DLP®, DLP Link and the DLP logo are
registered trademarks of Texas Instruments and BrilliantColor™ is a trademark of Texas
Instruments. InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or
trademarks of InFocus Corporation in the United States and other countries.
NOTE: This product is covered electrical and electronic equipment
under the European Union's Waste from Electrical and Electronic
Equipment ("WEEE") Directive (2002/96/EC). The WEEE Directive
requires that covered equipment be collected and managed
separately from typical household waste in all EU member states.
Please follow the guidance of your local environmental authority or
ask the shop where you purchased the product for collection or
recycling options.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by InFocus Corporation may
void authority to operate the equipment.
Canada
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la
classe B est conforme à la norme NMB-003 du Canada.
This device complies with RSS-210 of the Industry Canada Rules.
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils
radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes:
(1) le dispositif ne doit pas produire de brouillage préjudiciable, et
(2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
1

Advertisement

loading

Summary of Contents for InFocus IN3924

  • Page 1 Texas Instruments and BrilliantColor™ is a trademark of Texas classe B est conforme à la norme NMB-003 du Canada. Instruments. InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or This device complies with RSS-210 of the Industry Canada Rules.
  • Page 2 Agency Approvals cULus Other specific Country Approvals may apply. Please see product certification label. This document applies to regulatory model IN3924/IN3926. Input ratings: 100-240Vac, 3.2A, 50-60Hz InFocus reserves the right to alter product offerings and specifications at any time without notice.
  • Page 3 Table of Contents Wand Features Buttons and Wand Tip Introduction Troubleshooting LiteBoard Positioning the projector Maintenance Connecting a computer source Cleaning the lens VGA connection Using the security lock HDMI connection Replacing the projection lamp Connecting power Optional computer connections Displaying an image Adjusting the image Connecting a video device...
  • Page 4 Place the projector in a horizontal position no greater than 15 degrees off • Only genuine InFocus lamps are tested for use in this projector. Use of non axis. InFocus lamps may cause electrical shock and fire, and may void the projector •...
  • Page 5 Your new digital projector is simple to connect, easy to use, and straightforward to maintain. It is a versatile projector that is flexible enough for business presentations and home video viewing too. IN3924 has native XGA 1024 x 768 keypad resolution, and IN3926 has native WXGA 1280 x 800 resolution.
  • Page 6 LAN (RJ45 for network control and video over LAN) • 12 volt DC output (for screen trigger) USB type A microphone in security lock • RS232 (Serial command codes available at www.infocus.com/support) 12V DC output USB mini B composite video...
  • Page 7 Here are some general guidelines: (inches/m) (inches/m) (inches/m) • Position the projector on a flat surface at a right angle to the screen. IN3924 50”/1.3m 40”/1.0m 19”/0.5m must be at least 45” (1.0m) from the projection screen, and IN3926 must be 60”/1.5m...
  • Page 8 Connecting a computer source connect VGA cable VGA connection Connect one end of the provided computer cable to the C C omputer 1/Computer 2 connector on the projector and the other to the VGA connector on your computer. If you are using a desktop computer, you will need to disconnect the monitor cable from the computer’s video port first.
  • Page 9 Displaying an image press Power button Press the P P ower button. The Power LED lights orange, and the fans start to run. When the lamp comes on, the start up screen displays. It can take up to a minute for the image to achieve full brightness.
  • Page 10 If the left or right side of the screen is larger or smaller the other, you can turn the projector to the left or to the right a few degrees to square the image. Basic Menu MDL: IN3924 adjust Basic Menu FW: 1.02 Aspect Ratio ◄...

This manual is also suitable for:

In3926