Summary of Contents for e2-live RP-20F
- Page 1 Home Automation RP-20F AVhome BOX Instruction manual Edit by Amos /20150810...
-
Page 2: Table Of Contents
Home Automation Index E2-LIVE HOME APPLIANCES INTEGRATOR RP SERIES ....................3 HARDWARE ....................................4 Front panel........................................6 Rear panel.........................................4 Accessary ........................................5 IR different areas control...................................6 How to operate different IR control…………………………………………………………………………………………………………………..9 RP-20 Home Control Center……………………………………………………………………………………………………………..11 Software Installation of RP-20 ................................12 RP-20 make sure connect to PC................................12 Install USB driver ....................................12... - Page 3 Home Automation Version Description Date Ver. Revised contents Software Version 20130709 REV 1.2 Prototype 070803 2013/7/16 REV 1.2 Prototype 071002 2013/07/18 REV 1.2 Prototype 071805 2013/07/23 REV 1.2 Prototype 071805 2013/10/29 REV 1.5 Formal ver. 102902 Edit by Amos /20150810...
-
Page 4: E2-Live Home Appliances Integrator Rp Series
RF Tx/Rx 2 way transmission Frequency: 433.92MHz +/- 150KHz Digital ID code (0000~9999) Receiving distances：open space 60 meters RS-485 port (open protocol for system installer to control RP-20F) IR Learning processor Learning IR code：10KHz～455KHz。IR Code length：360 bit。 IR emitting area：7 zones Power sources: 5V 1.2A Adaptor... -
Page 5: Hardware
Home Automation Hardware Front Panel 9 pieces of infrared emission LED (First control point) 2 pieces of infrared emission LED can be fine tune up/down or left/right (First control point) IR in：IR signal input, from your remote control of appliances. -
Page 6: Accessary
Home Automation Accessary Extended IR emit wire X 2(1.8m) USB connector wire to PC Adaptor (5V 1.2A) side adhesive Double X 6 pieces CD catalogue & instruction manual Edit by Amos /20150810... -
Page 7: Ir Different Areas Control
Home Automation IR individual areas control RP-20F IR – total 7 areas Point 1: Surround infrared emission on top cover, has the same time emission with the point 1 port of the rear panel Surround emission Point 1 wired IR output... - Page 8 All emission,the model can achieve the same effect as well. All emission support all kind of remote controller of e2-Live. such as RC-09, itouch, VC-1500 Consistent with previous operating mode, HT-100, RP-20 software, etc., select the device (TV, DVD ...) first, then press (Power, CH +, CH- ..), After RP-20 received, all of the IR emitor will...
- Page 9 Home Automation Point 2 ~ 7 are wired control 1. Appliances in Audio/Video cabinet tank: IR signals cannot penetrate the veil, if the device is placed in the cabinet tank, IR emission lines need to be extended to the cabinet in order to control 2.
-
Page 10: How To Operate Different Ir Control
Individual IR control are related with RP-20 wiring and scenario editing actions, according to installation environment, make sure which device need to be individual control, and with the matching use of hardware and software. The following, for the above-mentioned current e2-Live system provide individual operator interface will be described. - Page 11 Home Automation , 2nd press , 3rd press ,then point 2 of IR emit 1st press device, example press press , then point of 3 IR emit 1st press device, example Use itouch (use with PC-09W or PC-09I, Wi-Fi emission)
-
Page 12: Rp-20 Home Control Center
Click RP-20 executive program to auto run installation During installation the program may ask you to download the update system of framework, Each computer may have different necessary, please make sure your PC can be connected to network, RP-20F will install necessary program automatically. -
Page 13: Rp-20 Make Sure Connect To Pc
Home Automation RP-20 make sure connect to PC Remove the connector wire out of the package, connect RP-20 and PC Support PC system Windows XP Windows 7 (32/64 位元) Windows 8 (32/64 位元) Note：By using this connector wire to connecting RP-20 with PC to setting any parameters through... - Page 14 If you have any of the above circumstances occur, which means that you need to install RP-20F USB driver manually. take the CD out of the package insert into the CD slot, click USB driver to install.
- Page 15 Home Automation After installation, please re-plug RP-20F USB once again, let the computer detect again. Finish Please choose 目前 the same COM RP-20 取 position for RP-20 得的連線 COM 位 Open RP-20 will automatically appear maybe several connectable positions of Click DETECT, COM.
-
Page 16: Rp-20 Software
Home Automation RP-20 software Connection Before RP-20 be open, please use USB wire connect RP-20 with PC, then COM port will be detected Home page setting If RP-20 AVhome Box had been connected to PC, then press Detect to automatically find out the connection of COM port. -
Page 17: Functions
Home Automation Functions ID Setting Here will display the instructions Input 4 digital ID code, Press “wright” to input (0000~9999) When enter impleted 4 digital numbers, it will be field with “0” in front of your input numbers, such as input” 123”, the actual ID would be “0123”, input “66”, would be “0066”... -
Page 18: Setting Id Of Ipower(Ps-301Or Ps-302)
Home Automation Setting ID of iPower (PS-301 or PS-302) RP-20 work together with iPower to make sure the devices’s power is ON or OFF. This special designed is to solve bland power ON/OFF control on scenario mansging. Perform this function, please plug your home appliances in smart socket of iPower. Use this page, you can setting the location of remote control. -
Page 19: Ir Learning
Home Automation IR Learning Preparatory actions before the operation： Tools needed: the original remote control of home appliances Make sure your home appliances is in the status of energized (Through the phone to activate the camera function), facing camera of your smart phone, press any button of any remote controller, if the emitting light of your remote controller can be seen, that means the emission of remote controller is in normal situation. - Page 20 Home Automation 29 action button will enable the buttons to have the function of press 3. Press corresponding function of a button on, such as ： Buzzer Short Bi Flash Blue LED 4. Pick up your remote controller of appliances, facing emission LED to RP-20 ”IR in” then press down the power button to input power ON/OFF code.
-
Page 21: Situation Of Need To Re-Learning
Home Automation 5. Repeat step 2~3 to continually to learn remote signal into RP-20 Situations of need to re-learn Buzzert One long, one short 1.After input IR signal, if Red flash twice Blue stable on Please re-press the button of appliance IR signal... -
Page 22: Leave Learning Mode
Home Automation Leave Learning Mode 1.Completed learning all of your appliances IR, please press “Stop Learning” for interup learning mode.” 2. In learning mode, no action over 15 seconds, RP-20 will leave learning mode automatiically Bizzer One long Bi~... - Page 23 Home Automation RP-20 can specify a different signal IR emitting region If you just want to verify that learning is successful, select "All emit” Sequence of operations: 1. Select equipment 2. Select "All emit" 3. Press the right action key Make sure the corresponding buttons are successfully remote control, if there is not, please repeat the learning sequence.
-
Page 24: Scenario Setting
Home Automation Scenario Setting Edit lighting & curtain Editable Devices Keys Actions Setting Light 01 01~12 Lighting 24 Macros Light 02 ON/OFF Light 03 ALL ON/ALL Light 04 Light 05 Curttain (specify) RP-20AVhome Box1~24 Macros ID can be specify difference with RP-20 to corresponding Please note that in use of any remote control device operation, lighting, curtain, and iPower. -
Page 25: Home Appliances
Home Automation Edit Home Appliances Interval: (only appliance action can be inserted interval) from 1 to 60 seconds, up/down to choose or key in the wanted numbers of seconds, maxmum is 60 seconds, more than 60 seconds are limited to 60 seconds. -
Page 26: Scenario Tool
Home Automation Scenario tool After data selected, press here for adding one new command on the bottom of the list Select and move edited data up and down for smooth scenario control Recovery a previous action, you can always forward... -
Page 27: Save
Home Automation According to the following steps, you could insert one action into scenario edit setting program planned well your action conditions, press to add in this edit setting row Click this edit setting row, use to move this edit setting row to where you want be placed... -
Page 28: Scenario Validation
Scenario editing note: rich scenario editing functions let e2-Live scenarios easier to play with the RP-20 provides a performance of the operation Also need special attention to several important functions when editing a scenario, in order to ensure actually perform the operation of scenarios. - Page 29 Home Automation function. 4. RP-20 provide different ID for lighting and curtain control, please make sure and input the scenario’s ID before saving, this ID would be stored to RP-20 while saving. 5. After scenario storage, please use Control Verification/Scenario Verification to test immediately to make sure your setting is correct and adjust instantly.
-
Page 30: Control Validation
RP-20 software : The purpose of control verification is to make sure its works after IR learning and scenario setting, it also provide remote control of lighting and curtain, it could be remote control all function of e2-Live via this software. In operation, the network connections of RP-20 or PC must be maintained. - Page 31 Home Automation Appliances Infrared control Select device-- IR emission location-- Action button Scenario verifications 。 Press button of scenario 01~24，RP-20 will be executed immediately, be careful to operate, during operation of scenario, it does not accept others remote commands again.
-
Page 32: Back Up
Home Automation Backup Setting Backup recovery For RP-20 to read out the backup setting data The information of RP-20 software could backup or recovery are as follow： 1. Remote ID The default storage path, 2. Infrared learning data suggest do not changed 3. -
Page 33: Id & Scenario
Home Automation Backup purpose 1. If there is any probrom of RP-20, then you could revovery back to initial status 2. Copy to another RP-20 Recovery： ID & Scenario For RP-20 software setting is finished【Scenario & ID data】, You can save as a file to PC RP-20 can save a single or all of the scenarios to PC for storage, and read back to RP-20 by Input. - Page 34 Home Automation Output: Save the current scenario settings to PC for later revised using (could be one or more) The default storage path, Output file suggest keep the path Press File names can be Open/Close/Muting RP-20 modified in either...
-
Page 35: About
Home Automation RP-20 host has received. After editing operation is completed with the relevant settings, you can choose to turn off the buzzer About Restore factory settings： Buzzer IR learning data and scenario setting will be cleare. Please be... - Page 36 FCC Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Need help?
Do you have a question about the RP-20F and is the answer not in the manual?
Questions and answers