Advertisement

Quick Links

FiberHome/SM/GZF850-VL
GZF850-VL Repeater
(C27Y02JW01YF)

User Manual

Nov. 2010

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GZF850-VL and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for FiberHome GZF850-VL

  • Page 1: User Manual

    FiberHome/SM/GZF850-VL GZF850-VL Repeater (C27Y02JW01YF) User Manual Nov. 2010...
  • Page 2 FiberHome reserves the right to make changes without further notice to any products herein to improve reliability, function or design. FiberHome does not assume any liability arising out of the application or use any product or circuit described herein. No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any means without the prior written permission of FiberHome Corporation.
  • Page 3 Instruction for your safety Please be sure to pay attention to all cautions and warnings before using the system. Incorrect usage could lead to an electrical shock, damage to the system or a fire hazard. ■Warning  Do not modify, disassemble or remove the cover. These actions could cause electrical shock.
  • Page 4 Preface GZF850-VL Repeater is widely used for constructing a hybrid mobile communications network. It receives and amplifies forward and reverse Radio Frequency (RF) signal to extend the coverage of base station. This user manual covers the system frame, technical specification, operation and maintenance of software of the repeater.
  • Page 5: Table Of Contents

    INDEX 1. GENERAL ............................1 1.1 S ..........................1 YSTEM RAME 1.2 P ......................... 2 RODUCT EATURES 1.3 H ............3 ARDWARE AND OFTWARE ONFIGURATION EQUIREMENT 1.3.1 Computer Hardware ......................3 1.3.2 Computer Software ....................... 3 1.4 T ......................3 ECHNICAL PECIFICATION 1.4.1 Specification of GZF850 –...
  • Page 6: General

    User Manual 1. General 1.1 System Frame The following figure shows the system frame of repeater. Downlink Donor ANT Service ANT D L ATT TCXO UL ATT Power Supply Uplink Battery RF signal flow M&C signal flow Antenna GZF850 – VL (C27Y02JW01YF)
  • Page 7: Product Features

    User Manual 1.2 Product Features  Excellent performance: FiberHome provides wireless repeaters with state-of-the-art performance such as minimized noise figure, time delay and IMD, excellent link balance and out-of-band suppression.  Modular design: Modular design is easier for operators to make upgrade and maintenance.
  • Page 8: Hardware And Software Configuration Requirement

    User Manual 1.3 Hardware and Software Configuration Requirement 1.3.1 Computer Hardware  CPU primary frequency:1.8G or above, 256M memory or above, above 16M graphic memory, 15" display with pixel of 800×600;  Options: 16-bit sound card, sound box, laser or jet printer. 1.3.2 Computer Software ...
  • Page 9: Other Specification

    User Manual ≤6dB Pass Band Ripple ≤9μs Group Delay Automatic Level Control Within 2dB or shut off Spurious ≤-36dBm 9kHz~1GHz/100kHz Emission(out 1GHz~12.75GHz/1M of working ≤-30dBm band 2.5MHz ≤1.5 VSWR 1.4.2 Other Specification MECHANICAL SPECIFICATION Dimensions Approx. 420×270×70mm Weight Approx. 9.0kg Ingress Protection Class Indoor use ENVIRONMENT SPECIFICATION...
  • Page 10: Structure

    User Manual 1.6 Structure 1.6.1 Figure of Repeater 1.6.2 Figure of Side Panel DC IN Donor ANT Local interface: RS232 UL/P Status LED DL/P Status LED Power Status LED...
  • Page 11: Indication Specification

    User Manual Service ANT 1.6.3 Indication Specification  Donor ANT: to be connected outdoor antenna.  Service ANT: to be connected indoor antenna.  POWER: when normal working, power supply status is green. 1.6.4 Dimension H: 70mm 40mm L: 420mm W: 270mm 125mm 70mm...
  • Page 12: Applications

    User Manual 2. Applications Accessing the signal by using a small Yagi antenna or Logarithm period antenna, low power repeater amplifies the signal and combines the indoor distribution system, which quickly improve the signal in shadowy or blind zones. Yagi ANT Ceiling ANT Splitter Repeater...
  • Page 13: Installations

    User Manual Indoor Distribute System 3. Installations Sketch Map  Firstly, select an appropriate position to mount. The signal booster is better to be mounted close to walls. At the position selected, punch a hole in the wall as shown in the diagram and aim the bolt at the hole.
  • Page 14: Site Commissioning

    4. Site Commissioning Note: Please excuse us for not giving any further notice about any changes of operation. FiberHome privileges to the final explanation of EMS. Our EMS has two sets of software, one is local version monitor software, and the other is the SQL version monitor software.
  • Page 15: Install The Software

    User Manual 4.1 Install the Software 4.1.1 Install the Communication Server Set up the communication server as follows:...
  • Page 16 User Manual...
  • Page 17: Install The Local Version Monitor Software

    User Manual 4.1.2 Install the Local Version Monitor Software...
  • Page 18 User Manual...
  • Page 19 User Manual Click the “Finish” button, the monitor software can be installed successfully.
  • Page 20: Configure The Software

    User Manual 4.2 Configure the Software The following steps are the process of connecting PC or laptop to the repeater on the site. Be sure the connecting cable is RS232. 4.2.1 Configure the Communication Server Running the communication server first, click the icon of the communication server with the right button of the mouse, and then choose configure to get access into the Communication Server Configuration.
  • Page 21 User Manual For local monitoring, choose “COM LINK” and “COM1”, and then click “OK”. We need RS232 cable to connect the repeater with the PC or laptop.
  • Page 22: Configure The Monitor Software

    User Manual The pin 2 /3 /5 of the RS232 cable are connected directly, the remaining pins are not connected. 4.2.2 Configure the Monitor Software Turn to “C:\Program Files\hongxin\Client (LOC)”, and run file “configure”. Choose suitable customer and click “OK”.
  • Page 23: Initial Monitor Settings

    User Manual 4.3 Initial Monitor Settings Run EMS, and then enter suited user name and password. We provide three sets of orders to indicate the different privilege respectively which are shown as follows: User Name Password Purview query query query only operate operate query and operate only...
  • Page 24 User Manual Main interface as follow: Click right button of the mouse, then add the province and city:...
  • Page 25 User Manual...
  • Page 26 User Manual Finally, add repeater and configure parameters:...
  • Page 27: Monitor Interface Illustration

    User Manual  Protocol: HX3.0  Name: GZF850 – V  Type: Frequency Selection Repeater  Device No: FF  Comm Mode: COM LINK  Net Type: GSM  SIM(UIM): 13566666666  Position: WRI  Manufacturer: Hongxin  Model: GZF850 – V Note: Please refer to local engineer’s suggestion for actual parameters for above items.
  • Page 28 User Manual Please click “Set” first then carries on the following steps.
  • Page 29: Principle Settings

    User Manual 4.5Principle Settings 4.5.1 Power Limit Choose “read” to query each threshold of alarm. Please not modify such data. 4.5.2 ATT Settings Before the ATT setting, please click the button “Read” first. Then you will know the information before you set the ATT.
  • Page 30: On-Off Setting

    User Manual 4.5.3 On-off Setting PA On-Off of repeater defaults set as “on”. If on the site, please check the PA On-Off interface whether the output power is tested every week. Read first, if the PA On-Off is “off”, please change into “on” and click “set”.
  • Page 31: Frequency Configuration

    User Manual 4.5.4 Frequency Configuration...
  • Page 32: Extend Parameter Settings

    User Manual PLL is applicable for setting work frequency. The performance is shown as follows: Frequency Range Bandwidth Range of ARFCN 850MHz 25 MHz 128-251 Work PLLs: It is applicable to set the quantity of frequency adjustable as 2. Shift PLLs: It is applicable to set the quantity of frequency shifting as 0. . Work Channel 1: It displays relative ARFCN in 25 MHz bandwidth of 850M frequency.
  • Page 33 User Manual Note: Please not modify the repeater information.

Table of Contents