Competition Electronics Pocket Pro II User's Manual And Operating Instructions

Competition Electronics Pocket Pro II User's Manual And Operating Instructions

Advertisement

OPERATING INSTRUCTIONS
(gray model# CEI-4710)
Please read this manual!
This manual contains setup information necessary to
achieve proper performance from your Pocket Pro II.
815.874.8001
(blue model# CEI-4700)
competitionelectronics.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Pocket Pro II and is the answer not in the manual?

Questions and answers

Summary of Contents for Competition Electronics Pocket Pro II

  • Page 1 OPERATING INSTRUCTIONS (blue model# CEI-4700) (gray model# CEI-4710) Please read this manual! This manual contains setup information necessary to achieve proper performance from your Pocket Pro II. 815.874.8001 • competitionelectronics.com...
  • Page 2: Table Of Contents

    User Manual / Operating Instructions Table of Contents Battery Installation . . . . . . . . . . . . . . . . . . 2 Setting the Main Display Type .
  • Page 3: Battery Installation

    . This will prevent battery discharge in the event it is not turned off after use . To wake up the timer, press the SET/ON button . Forced Shutdown To turn the Pocket Pro II off, press and hold the MENU DOWN button for approximately 3 seconds .
  • Page 4: Quick Start

    If you want to get started right away, all you have to do is press the start button on the side and shoot . The Pocket Pro II comes from the factory configured and ready to run . After the timer shuts down, press the SET/ON button to turn it on .
  • Page 5: Shot Detection

    User Manual / Operating Instructions Shot Detection Each time a shot is detected, it will be added to the “shot string” maintained within the timer . The timer will automatically calculate the “split time . ” Split time is the time between the current shot and the previous shot .
  • Page 6: Setting The Par Time (Second Beep)

    User Manual / Operating Instructions Setting the PAR Time (second beep) The par time setting (also known as the “second beep”) comes configured from the factory for 0 seconds . When the par time is set to 0, the timer will beep only once, at the start of a timing cycle .
  • Page 7: Display Backlighting

    User Manual / Operating Instructions Fixed Delay On the same screen as mentioned in the previous section, select “RANDOM . ” Now, using the MENU UP/DOWN button, advance to the “RANDOM START TIME – MINIMUM” and “RANDOM START TIME – MAXIMUM” display screens . In both screens, select the same delay time, between .5 seconds and 9 .9 seconds .
  • Page 8: Beeper Volume

    . A new setting will be saved automatically . Setting the Main Display Type The Pocket Pro II can be configured to show three different types of main displays . These are selected from the “MAIN SCREEN TYPE” menu, and are described below .
  • Page 9 START is pressed again . The normal shot dead time setting is overridden when in RPM mode and set to a fixed value of 0 .032 seconds . This allows the Pocket Pro II to detect shots at rates of up to 1800 RPM .
  • Page 10: Shot Dead Time

    The SHOT DEAD TIME feature is used to reduce false shot recordings due to echoes or ringing . Once a shot is detected, the Pocket Pro II will disregard subsequent shots for a short period of time . The default setting is .11 seconds, but can be adjusted from .05 to .12 seconds .
  • Page 11: Setting The Date And Time

    User Manual / Operating Instructions Setting the Date and Time Using the MENU UP/DOWN buttons, cycle through the MONTH, DAY, YEAR, HOURS, and MINUTES display screens using the SET UP/DOWN buttons to set the date and time . To synchronize to the nearest second, set the “MINUTES” value and at the mark, advance to the next/previous display screen .
  • Page 12: Battery Status

    . This will allow the session to continue in the event a replacement battery is not readily available . When the battery voltage becomes depleted to less than 6 volts, the Pocket Pro II will shut down to avoid undefined operation . Resetting the Timer to Factory Defaults To reset factory default values within your timer, remove the battery, then hold down the “Start”...
  • Page 13: Timer "Wraparound

    . Accuracy The Pocket Pro II measures internally to a resolution of 1 mSec, but shot displays, splits, etc . are internally rounded to the nearest 10 mSec . For this reason, RPM readings may appear to be inaccurate when manually calculated using the displayed shot string values .
  • Page 14: Specifications

    • Battery type: 9 volt alkaline Pocket Pro II Carrying Case (model# CEI-4707) $10.95 • This handy case will protect your timer during transport and storage. • It features a zipper storage compartment for spare batteries, velcro belt strap, and a Competition Electronics embroidered logo . • Economically priced at $10.95 which includes postage to continental U .S .A . residents . To Order Call 815-874-8001 or visit our website at competitionelectronics.com...
  • Page 15: Limited Warranty

    * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * COMPETITION ELECTRONICS, INC., warrants the Pocket Pro II manufactured by it to be free from defects in material and work- manship for a period of 2 years from date of purchase by the original purchaser for use.
  • Page 16 User Manual / Operating Instructions www.competitionelectronics.com Rev 5-2013...

Table of Contents

Save PDF