Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Motion VISION X
Summary of Contents for Motion VISION X
- Page 1 u s e r ’ s m a n u a l...
- Page 2 No naked flame sources, such as candles, should be placed on the product. Do not expose this apparatus to dripping or splashing and ensure that no MOTION VISION X objects filled with liquids, such as vases, are placed on the apparatus.
- Page 3 CE: Hereby, MartinLogan Ltd., declares that this Motion Vision X is in compliance equipment off and on, the user is encouraged to try to correct the interference by one...
-
Page 4: Table Of Contents
Serial Number:_____________________________ Introduction and Overview ....6 Placement and Mounting ..... . . 6 Record your serial number here for easy reference. -
Page 6: Introduction And Overview
MartinLogan design. what we love. The Motion Vision X reproduces front left, right, and center channels via the system’s dedicated MartinLogan’s dedicated in-house engineering tweeters and woofers. Surround channels are simu-... - Page 7 WARNING! We strongly recom- Required hardware (included): mend locating the wall bracket so • (1) Installation template at least one of the screw locations • (1) Wall bracket attaches to a stud. WARNING! To prevent injury, this apparatus must be secure- Required hardware (not included): ly attached to the floor/wall in accordance •...
- Page 8 If no stud is found: use the center most screw Fig. 2a location and drill a pilot hole for the wall anchor. Install a wall anchor at this location. If a wall stud is found: drill a pilot hole into the stud. 4 Using a screw, attach the wall bracket to the wall.
-
Page 9: Connection
Fig. 3 ONNECTION WARNING! Turn your soundbar in any subsequent location is suitable before con- off before making or breaking any necting and operating the soundbar. Substantially signal connections! WARNING! impaired performance or severe damage may The power cord should not be occur to the soundbar if operation is attempted installed, removed, or left detached from the from an incorrect AC power source. - Page 10 Connections are made at the signal input section a 2-channel stereo mix before sending them to the on the rear electronics panel of the soundbar. Your television’s digital output. soundbar features three wired audio inputs: • 1 x Digital Optical inputs Most users will want to run cables directly from •...
-
Page 11: An Introduction To Audio Connections
source, you may need to set the player’s digital sound. Please refer to your player’s manual. audio output to “Bitstream” (also called “Raw”, • In a setup where HDMI is used to connect your “Direct Digital”, or “High Bit Rate”). If “PCM” is audio/video source component to your television, selected you’ll lose the multi-channel encoded you will likely need to run an additional digital... -
Page 12: Network Connection For Dts Play-Fi
will allow for multi-channel encoded audio to subwoofer connection, connect “Sub Out” from the reach the soundbar. soundbar to the “LFE In/Sub In” on the subwoofer. • Audio-only sources capable of only stereo output (such a portable media player docks or CD play- Use the soundbar’s menu system and choose ‘SUB er) will often connect directly to the soundbar via >... - Page 13 Fig. 6...
-
Page 14: Ir Input
nology are not capable of wireless connectivity devices from one another—a distance as little as with this soundbar—a wired connection will work two feet will often alleviate the interference. In the for these subwoofers. case of microwave ovens, the interference will only occur when the microwave is operating. -
Page 15: Dts Play-Fi
DTS P ® NETWORK REQUIREMENTS WI-FI SETUP AND STATUS BUTTON You must have the following to connect your soundbar The Wi-Fi Setup and Status button tells you what to your network: your soundbar is doing (fig. 7). • A wireless router. •... -
Page 16: Connecting To A Wireless Network: Wi-Fi Protected Setup (Wps)
new soundbar is plugged in, the Wi-Fi Setup app and open your iOS device’s Settings app. and Status button will start pulsing slowly. If c) Select Wi-fi in Settings. Ensure that Wi-Fi is the soundbar is already configured to connect enabled on your device. -
Page 17: Connecting To A Wired Network
without needing to enter a password. WPS is not 5 Now push the WPS button ( ) on your router. a standard feature on all routers, and only one wireless device can be set up at a time. 6. Once the Wi-Fi Setup and Status button is solid (not blinking), this indicates your soundbar is connected Check your router’s owner’s manual to see if WPS to the wireless network. -
Page 18: Controlling Multiple Speakers
3. If you have more than one Play-Fi speaker TIP! Primary and Secondary Speakers ® connected to your network, you will be prompted When streaming audio content to multiple devices, to select the speaker to which you want to stream. you will be asked to assign them to two categories: primary and secondary devices. -
Page 19: Updates And Rebooting
PDATES AND EBOOTING DTS PLAY-FI ® APP UPDATE SOUNDBAR FIRMWARE UPDATE If the DTS Play-Fi app on your mobile device or Your soundbar may occasionally require firmware PC requires an update, you will be notified that an updates. Please check www.martinlogan.com for update is available and guided through the update the latest firmware updates. -
Page 20: Remote Control
EMOTE ONTROL Your soundbar remote controls these functions: Caution! Danger of explosion if battery is incorrectly replaced. POWER: Turns the soundbar on and off. Replace only with the same or equivalent type. VOL+/VOL–: Adjusts volume level. MUTE: When muted, the soundbar will display PROGRAMMING A SECOND REMOTE ‘MUTE’. -
Page 21: An Overview Of The Menu Structure
VERVIEW OF THE TRUCTURE SUB [subwoofer, select subwoofer configuration] LEARN [learn remote codes for second remote control] –› * † NO.SUB [no sub, select when not using a subwoofer] –› VOL+ [volume up, program to respond to second remote] – › WIRED [wired, select when attaching a subwoofer via a cable] –... -
Page 22: Navigating The Menu
NAVIGATING THE MENU** Fig. 10 The menu is navigated using the ‘up/down/left/ right/enter’ navigation system. Up and Down are used to cycle through the menu and submenu options. Right or Enter are used to access a submenu or to select an option. Left is used to exit a submenu and go back one level (fig. -
Page 23: Bass Level
SUB > WIRELS > SYNC: This option will ini- BASS.LV > –10 to +10: Using the up/down tiate syncing with an SWT-2 equipped wireless directional buttons, choose the desired bass level subwoofer. With this option, the soundbar’s Sub (from –10dB to +10dB). Bass level output will be Out RCA connection is turned off. -
Page 24: Stereo
all 5.1-channels of information including simulated MENU OPTION: MODES surround channels. Activate by pressing the enter button and the soundbar will respond with ‘SET’. MODES: Enter the ‘MODES’ submenu by pressing the enter button. Here you may adjust the bass equal- SURRND >... -
Page 25: Power
DISPLY > AUTO.DM: [AUTO DIM] This option Please note: When learning from a second configures the soundbar’s display to be on at a remote, you will likely find it does not have buttons reduced brightness when a setting (such as volume that directly correspond with all available soundbar or input) is changed. -
Page 26: Source Name
Using the up/down directional buttons, you can • ANALOG [ANALOG INPUT] (direct access) select and program the following input names: • PLAYFI [Play-Fi INPUT] (direct access) Choose the command you want to program and • OPTIC [DIGITAL OPTICAL] press the enter button. The soundbar will respond with •... -
Page 27: Service
SERVCE > RESET > AT.HOME > CONFRM The ‘RESET’ function requires confirmation to > NO: Activate by pressing the enter button. reduce risk of performing an accidental reset. Choosing this option will exit without performing SERVCE > RESET > STORE > CONFRM: a reset. -
Page 28: Frequently Asked Questions
1 The appointed MartinLogan distributor for any (parts, labor, transportation) must be borne by the given country is responsible for warranty servicing owner of the MartinLogan product. only on units distributed by or through it in that coun- try in accordance with its applicable warranty. 3 If, after owning your speaker for six months, you relocate to a country other than the one in which 2 Should a MartinLogan product require ser-... -
Page 29: Troubleshooting
I have a MartinLogan subwoofer with listening to a number of brands—and above all a built-in SWT-2 wireless receiver. Do I else—trust your ears. Dealers are always the best have to use the wireless connection? source for information when purchasing additional No. - Page 30 • Verify you are within the recommended range releasing the button, two tones will play and of your wireless router. the soundbar will reboot. This reboot will cycle • Verify your mobile device or PC has its Wi-Fi the power off and on and force the soundbar to enabled or is otherwise connected to your reconnect to your network.
- Page 31 defeated. Some televisions will allow you to When using an aftermarket remote, the turn off the internal speaker via the television’s soundbar turns off when the television menu system. Other televisions may require you turns on to turn the television’s volume to “zero” or to •...
-
Page 32: Specifications
7 amps. High Frequency Drivers....Three 1” x 1.4” (2.6cm x 3.6cm) Folded Motion Transducers with 5.25” x 1.75” (13.3cm x 4.4cm) diaphragm. -
Page 33: Dimensional Drawings
IMENSIONAL RAWINGS MARTINLOGAN MOTION VISION X Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio and the double-D symbol are trademarks of Dolby Laboratories. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS, Inc. DTS, the Symbol, DTS in combination with the Symbol, and DTS Digital Surround are registered trademarks or trademarks of DTS, Inc.
Need help?
Do you have a question about the VISION X and is the answer not in the manual?
Questions and answers