Page 3
GSM Dual-Band GPRS Digital Mobile Phone The manual is applicable for ZTE i766 mobile phone...
Page 4
ZTE Corporation. ZTE Corporation reserves the right to make modifications on print errors or update specifications in this manual without prior notice. Version 1.0, Jul. 2008...
錯誤! 尚未定義樣式。 Before Use 1.1 Introduction Thank you for choosing ZTE Corporation’s “i766” GSM Dual-Band GPRS Digital Mobile Phone. To guarantee your mobile phone always in its best condition, please read this manual carefully and keep it for future use.
1.2 Safety Instructions If your mobile phone is lost or stolen, notify your service provider immediately to prevent others from abusing it. Meanwhile you need provide your service provider with your mobile phone’s IMEI, which is printed on the label on the back of your mobile phone (appears after the battery is taken out).
Page 11
錯誤! 尚未定義樣式。 of an electronic device or other problems. Pay special attention when you use your mobile phone near audiphone, pacemaker and/or other medical electronic devices, fire detector, auto-door and/or other auto-control equipments. For details on the influence caused by your mobile phone on pacemaker or other medical electronic devices, please consult the manufacturer or your local distributor.
Page 12
Waterproof Keep your mobile phone away from water. This may cause overheating, electric leakage or failure if water or any other kind of liquid enters your mobile phone. Disassemble Do not disassemble or reassemble your mobile phone because this might cause damage, electric leakage or circuit failure. Antenna Do not use your mobile phone if your antenna is damaged because this may cause body injury.
Page 13
錯誤! 尚未定義樣式。 performance, violate the warranty provisions or relevant national regulations about telecom terminals, or even cause body injury. Explosion Areas Please strictly follow relevant laws and regulations to turn off your mobile phone in or near the explosion areas. Emergency Calls Make sure your mobile phone is turned on and in the service area.
Page 14
Do not disassemble or reassemble the battery because this may result in leakage, overheating, explosion or fire. If the battery becomes hot, changes in color or gets deformed during the course of use, charging or storage, please immediately stop using and replace it.
Page 15
錯誤! 尚未定義樣式。 Do not use the charger if the power cable is damaged because this might cause fire or electric shock. Do not place water containers near the charger to avoid water splashing. If water or any other kind of liquid splashes on the charger, immediately remove the charger from the power socket to avoid overheating, fire, electric shock or failure.
1.4 Parts Definition 1.4.1 Appearance Earpiece Touch-screen shortcuts Right soft key Left soft key Numeric keys OK key Navigation keys Send key End Key...
1.4.3 Key Definitions Move the cursor to the left/right; In idle mode, press left key to enter “Multimedia”, press Left/right right key to enter “Messages”. Under the status of camera preview, press left/right key to adjust EV parameter. Move the cursor up/down; Move the cursor up/down to select menu options;...
錯誤! 尚未定義樣式。 1.4.4 Descriptions of touch-screen shortcuts In idle mode, click this icon to enter “Call History”. In idle mode, click this icon to enter “Video Player”. In idle mode, click this icon to enter “Messages”. In idle mode, click this icon to enter “Audio Player”. Click this icon to return to idle mode from current interface.
then releasing; “hold” means pressing and holding the key for about 2 seconds or more; “click” means clicking the corresponding icon on the screen with touch-pen. 1.5 Battery 1.5.1 Installing the Battery 1. Align the battery's contact points in the direction of the arrow as shown, and Insert the battery into the slot;...
錯誤! 尚未定義樣式。 1.5.2 Removing the Battery 1. Push down the battery back and take out the back cover; 2. Pull the battery in the direction of the arrow as shown and take out the battery.
Note: Please turn off your mobile phone before taking out the battery. 1.5.3 Charging the Battery The lithium battery can be used directly after being taken out from the package. To make the battery always in its best condition, please exhaust the capacity of the battery and then fully recharge it for the first three times.
錯誤! 尚未定義樣式。 Note: 1. Put your phone in ventilated place under normal temperature during charging. Use the original charger or those authenticated by the manufacturer. Using non-original charger may cause danger and violate the warranty provisions. 2. Charge your mobile phone in time when it is powered off automatically or prompts the lack of the power.
3. Turn off your mobile phone and remove the battery before taking out SIM card. 1.7 Insert and Remove Memory Card 1. Turn off your mobile phone, remove the battery and disconnect the external power; 2. Open the clasp in the direction of arrow as shown; 3.
Page 25
錯誤! 尚未定義樣式。 4. Close the clasp; 5. Secure the clasp in the direction of arrow as shown; 6. Turn off your mobile phone and remove the battery before taking out the memory card.
1.8 Power On/Off Press and hold End key until the power-on/off animation appears. After your turn on your mobile phone, it will automatically check whether or not SIM card is inserted or usable, and shows the following information on the screen in turn: Enter Phone Lock Code: if you’ve set the code.
錯誤! 尚未定義樣式。 Call 2.1 Make a Call You will be able to make or receive calls as the network provider’s logo appears on the screen. The bar at the left-up corner of the screen indicates network signal strength. The more bars there are, the stronger the signal will be.
finally dial the extension number. 2.1.3 Dial International Calls To dial an international call, click continuously until “+” appears on the screen. This will enable you to dial an international call anywhere even without knowing the international prefix. 2.1.4 Dial from Call History Every number you dialed or received will be saved in Call History.
錯誤! 尚未定義樣式。 “Any Key” to set. After the setting, press any key except “End” key to answer the call. Use headset to answer If the headset is connected, you can press the key on the headset to answer the call. 2.3 Emergency Calls You could make emergency calls without SIM card so long as you are in the area covered by the network.
Page 30
End: End the current conversation. New Call: Enter new dialing interface. Phone Book: Enter Phone Book. Message: Enter “Message”. MMS function will be disabled during the conversation due to the restriction of network occupancy. Sound Recorder: Record the current conversation. Mute: When “Mute”...
錯誤! 尚未定義樣式。 Call History “All Calls”, “Missed Calls”, “Dialed Calls”, and “Received Calls” are saved in “Call History”. If the records are full, the earliest saved records will be deleted. In idle mode, press OK key to enter the main menu, and then select “Call History”.
3.2 Delete Call Log 1. Select “Call History” in the main menu to select “Delete Call Log”. 2. Select “Missed Calls”, “Dialed Calls”, “Received Calls” or “Delete All”. 3.3 Call Time Under “Call Time”, you could select “Last Call Time”, “Total Sent”, “Total Received”...
錯誤! 尚未定義樣式。 Multimedia 5.1 Camera 1. Select ‘’Camera” to enter the preview interface, and press “Option”: Album: Enter Album to view the photos you’ve just taken; Camera Settings: Set “Shutter Sound”, “EV”, “Banding”, “Delay Timer”, and “Cont Shot”. Image Settings: Set “Image Size” and “Image Quality”. White Balance:Select “Auto”,...
Click to adjust EV parameters; Click to adjust the camera focus; Click FX to change effect settings; Click to delay the time; Click to set “Cont Shot”; Click to set “Image Quality”; Click to set “image size”; Click to complete “Capturing” and ask “Save Image?”. Note: The camera focus can not be adjusted when the image size is set maximum.
錯誤! 尚未定義樣式。 Delete All Files: Delete all videos. Sort: Select “By Name”, “By Type”, “By Time”, “By Size” or “None”. Storage: Select “Phone” or “Memory Card”. Select the video and press “Option” to set: Play: Play the select video. Settings: Set “Auto Repeat” Select a video and use handwriting pen to perform the following operations: Click...
into the mobile phone. Channel List: Edit up to 9 channels. Manual Input: Manually input a channel. Preset Auto Search: Automatically search for channels. Settings: After you turn on “Background Play”, “Record Format” and “Record Storage”. Record: Record the current channel. Append: Continue to record amr files on the current file.
錯誤! 尚未定義樣式。 Record: Start recording. Settings: Set “Pre. Storage” and “File Format”. List: View all the recorded files in the list. Select a recorded file and press “Options” to select:: Play: Play the selected file. Append: Continue to record amr files on the current file Rename: Change the name of recorded file.
2. After the above settings, press OK key to record videos. Under the record preview interface, you could use handwriting pen to perform the following operations: Click to record a new video. Click to pause. Click “Stop” to stop recording. Press “Back”...
錯誤! 尚未定義樣式。 Note: You could view the photos in “Album” only when they are saved in “Photos” folder of Phone or Memory Card. Select a photo and then press “Option” to select: View: View the photo. Browse Style: Select “List Style” or “Matrix Style”. Forward: Select “To Wallpaper”, “To Phone Book”, “To MMS”, “To Email”.
Page 40
Create Folder: Create a new folder and edit the folder name. Format: Format the selected storage. This would delete all the data saved in the selected storage. Select “Open” to open the relevant folder and file. Select a file and press “Option” to select: View: This option appears only when the phone supports the files.
錯誤! 尚未定義樣式。 Note: The phone supports Digital Rights Management (DRM). Phone Book In Phone Book, you could save the contact’s name, telephone number, mobile phone number, etc. The numbers could be saved either in Phone or SIM card. In idle mode, use the handwriting pen to enter the main menu. Under “Phone Book”, you could select the following functions:...
7.1 Quick Search Use the handwriting pen to click the first letter of your desired contact on the screen to quickly search for the contacts, or view all contacts in Contact list. You could perform the following operations to the current contact, such as “Call”, “Send MSG”, “View”, “Delete”, “Send vCard”, “Add New Entry”...
錯誤! 尚未定義樣式。 Set your personalized caller picture for the current number. Select the proper picture from “System”, “Phone” or “Card”, which could be previewed (the size of the picture selected from File Manager folder can not larger than 20K). Associate Sound Select the proper ring tone from “System”, “Phone”...
When copying all entries from Phone to SIM card, only the name and number will be copied. 7.6 Delete All Select “From SIM” to delete all entries saved in SIM card, and select “From Phone” to delete all entries saved in Phone. 7.7 Preferred Storage You could set the preferred storage location for the current number.
錯誤! 尚未定義樣式。 Messages 8.1 SMS Your mobile phone supports Enhanced Message Service (EMS), which allows you to insert picture, animation, cantus, sound, etc, or use template to create short message. Write Message 1. Enter “Write Message” to edit a short message. 2.
Page 46
recipient’s number (You could select multiple numbers from “Phone Book” or “Call Log”). Send By Group: you could send the message to all the contacts in the group. Insert: select “Use Template”, “Insert PHB Number”, “Insert PHB Name”, “Insert Bookmark” or “Insert Object”. Text Format: set “Text Style”, “Alignment”...
Page 47
錯誤! 尚未定義樣式。 Reply: Reply to the message. Reply through MMS: Reply to the message by MMS. Delete: Delete the message. Forward: Forward the message to other recipient. Call: Dial the sender’s number. Get Number: Get the sender’s phone number or the number in the message text, you can dial the number or save the number into Contact.
Page 48
Delete Message You could select “Delete Inbox”, “Delete Outbox”, “Delete Drafts” or “Delete All”. Template There are 10 short messages predefined in your mobile phone. You could select “Edit”, “Erase” or “Write Message”. Settings Before using Messages, you need perform relevant settings: Profile Settings: Please contact your local network provider to obtain the service center number.
錯誤! 尚未定義樣式。 know whether or not the other party has received your message. Memory Status: display the memory space for SMS in SIM card and Phone. Preferred Storage: select “SIM” or “Phone” as the default storage media for SMS. SMS Counter You could view the number of messages “Sent”...
Page 50
Your mobile phone supports MMS. After necessary settings, you could send/receive MMS. Write Message 1. Enter “Write Message” to edit: To: You could select “Add Number” or “Add E-mail”; Cc: If the network supports, you could add more recipients. The operation is the same as “To”.
Page 51
錯誤! 尚未定義樣式。 changed to “RE: original subject”. Reply by SMS: Edit SMS and reply to the sender. Reply to all: Edit MMS and reply to all. Forward: Forward the current MMS. Delete: Delete the current MMS. Delete All: Delete all MMS. Properties: View the details of MMS.
Page 52
Template Your mobile phone stores 5 predefined multimedia messages. Press “Option” to select “View”, “Write Message” or “Properties”. Message Settings Before using MMS, you must perform some necessary settings. Compose You could set “Creation Mode”, “Image Resizing” and “Auto Signature”. Send You could set “Validity period”, “Delivery report”, “Read report”, “Priority”, “Slide Timing”...
錯誤! 尚未定義樣式。 Memory Status You could check the memory status. Note: The use of “Delivery Report” and “Anonymous” depends on your network service provided by your provider. For more details, please consult your network provider. Your mobile phone has reserved some usable space to save MMS.
Page 54
Cc: If the network supports, you could add more recipients. The operation is the same as “To”. Bcc: If the network supports, you could add more blind recipients. The operation is the same as “To”. Subject: The subject could be null. Attachment: You could select “Attachment”...
Page 55
錯誤! 尚未定義樣式。 If current incoming protocol is set to IMAP4, You could perform the following operations after reading email: “Read”, “Next Page”, “Previous Page” or “Jump To Page”. Unsent The draft stores those Email you are not ready to send. You could perform the following operations: “Send”, “Save and Send”, “Edit”, “Move To Draft”...
Your mobile phone stores 10 predefined multimedia messages. Press “Option” to select “Edit”, “Erase” or “Write Email”. 8.4 Voice Mail Server When you are unable to answer the call, you could let the other party leave a message for you through voice mail server. You could visit voice mail server to listen to the message later.
錯誤! 尚未定義樣式。 Fun&Games 9.1 Games Your mobile phone provides one Games. Enter the menu and view the operation descriptions. 9.2 E-Book Reader Enter “Bookshelf” and press “Option” to select:: Open E-Book: Open E-Book, and press “Option” to select “Find”, “Jump To”, “Go To Bookmark”, “Add Bookmark”, “Delete Bookmark”, “Book Info”, “Settings”, “Apply Global Settings”...
Sort: You could select “By Name”, “By Type”, “By Time”, “By Size” or “None”. Apply Global Settings: Restore factory default settings. Note: The list will be automatically updated as you put txt files into “E-book” directory of the phone or memory card. 9.3 Melody Compose You could compose your favorable music as the ringtone for incoming call and alarm.
Page 59
錯誤! 尚未定義樣式。 Edit Insert: insert a note. Edit: edit a note. Play: play the composed ringtone. Up key: raise the tone of current note. Down key: lower the tone of current note. Left key: move the cursor to the left. Right key: move the cursor to the right.
Services 10. 1 WAP Your mobile phone supports Wireless Application Protocol (WAP). You could get access to the services provided by your network provider. It allows you to get information about news, weather forecast, airline flights, etc. These services are especially designed for the mobile phone, and they are maintained by WAP provider.
錯誤! 尚未定義樣式。 Note: Before use, please make sure your bookmark list is not empty. In order to avoid this, a few common websites have been preset to you in your mobile phone. Recent Pages: Display the recent pages you’ve visited. If you have select the history, simply select “Goto”...
the default value is wap. Password: Edit the password for dial server (not WAP gateway), the default value is wap. Line Type: Select the line type “ISDN” or “Analogue”. Speed: Select the data connection speed “4.8Kbps”, “9.6Kbps” or “14.4Kbps”. DNS: Select WAP’s DNS. GPRS In “GPRS”, display the list of data accounts.
錯誤! 尚未定義樣式。 Audio Player Your mobile supports audio file formats such as midi、mp3 and amr. 1. Select “Audio Player” to enter the interface, and press “Option” to select “Settings”: Pre. Play List: Select the file from “Phone” or “Memory Card”. Background Play: Select “On”...
Page 64
Select an audio file, and press “Option” “Play”: Press Up key to enter “Player Settings”, press Down key to enter the play list, and press OK key to pause/resume. Press side keys to adjust the volume. Press Right key to play the next file, and press Left key to play the previous one.
錯誤! 尚未定義樣式。 Extra 12.1 Calendar Enter “Calendar”, the calendar in current month will be displayed on the screen and the current date will be marked by a background box in special color. You could press navigation keys or click the direction arrows on the screen to browse the dates and the information on the screen will also change consequently.
12.3 World Clock Press left/right navigation key to view the time of different cities. 12.4 Calculator Your mobile phone provides a calculator to perform simple calculations. You could add, subtract, multiply or divide, and select M+, M-, MR, and MC to perform relevant operations. Descriptions of M+, M-, MR and MC MR: Read the data saved in current memory.
錯誤! 尚未定義樣式。 12.5 Typical Stopwatch You could select “Spit Timing”, “Lap Timing” or “View record”. 12.6 nWay Stopwatch Press 4 different navigation keys to record the different timing respectively. Note: Press LSK to stop time measuring, and hold left soft key to clear up all the records.
Analog TV Your mobile phone provides analog TV function. Select “Analog TV” and enter. The TV effect depends on your local TV station signal. You could use video cable to connect your mobile phone and cable TV interface. Please follow the instructions in the figure below to pull out the antenna at the end of touch-pen, and rotate the antenna to achieve the best effect.
錯誤! 尚未定義樣式。 Antenna Press “Options” to select: Select Area: Select your local area. Mode Selection: Select “Analog TV” or “Cable TV”. Channel List: Display the list of the best channels you’ve searched for. Auto Search: Automatically search for channels. Manual Input: Manually input a channel. Settings: Select “Default Settings”.
completed. If the calibration is still not accurate as you make sure to click the center every time, you should refer to 14.7 Restore Factory Settings. 14.2 User Profiles Your mobile phone provides multiple profiles, which allows you to perform personalized settings of “Incoming Call Alert”, “Alarm”, “Message Alert”, “Keypad Tone”, “Alert Tone”...
Page 71
錯誤! 尚未定義樣式。 Time and Date You could set “Date”, “Time”, “Date Format” and “Time Format”. Scheduled Power On/Off You could edit up to 4 groups of power on/off time. Press “Edit” to set “Status”, “Type” and “Time”. Note: The time should be set different y to avoid conflict. Auto Keypad Lock You could prevent misoperation resulting from improper key press.
14.4 Call Setup Call Waiting After this function is activated, the system will inform you if there is another incoming call. Please contact your network provider for details. Call Divert This function allows you to divert incoming call to another designated number. Note: This function requires network support, so please contact your network provider for details.
錯誤! 尚未定義樣式。 You could edit the Black List. After you select “On” under Mode, the incoming call from the numbers in the Black List will be rejected. Auto Redial You could turn on/off this function. If the other party doesn’t answer the call as you select “On”, your mobile phone will automatically redial after a while.
Page 74
to unlock your SIM card. You need input correct PIN code to unlock your SIM card as you turn on your mobile phone next time. If “SIM Lock” is set “ON”, select “OFF” to cancel the protection. Note: Your SIM card will be locked if you enter wrong PIN code continuously for three times.
Page 75
錯誤! 尚未定義樣式。 The default password is 0000. Please change to your own password as soon as possible. Call Barring Note: Please contact your network provider for details since some providers might not provide call barring service. When applying for this service, you will get a four-digit password provided by your provider to activate call barring.
Fixed Dial List or a few numbers. Enter “Fixed Dial” to select: Mode: Input PIN2 code to turn ON/OFF Fixed Dial function. Fixed Dial List: Edit a maximum of 10 fixed dial numbers. Press “Option” to select “Edit” or “Find in PHB”. Note: You need input PIN2 code to turn on/off fixed dial function.
Page 77
錯誤! 尚未定義樣式。 password, and press “OK” to restore factory settings.
USB Data Function 15.1 Mass Storage Mass storage indicates your mobile phone supports mobile storage. As the phone is turned off, connect your mobile phone with PC through USB data cable. In this case, your mobile phone can be used as U disk. As the phone is turned on, connect your mobile phone with PC through USB data cable.
錯誤! 尚未定義樣式。 Input Methods 16.1 General Description Your mobile phone supports handwriting input. The handwriting input methods include abc/ABC/ES/es Input method, 123 Input method and Symbol Input method. Under handwriting input mode, you could enter the inputs in the following two ways: Use the handwriting pen.
Right Soft Key: Generally used to return or clear. Key: Generally used to switch different input method. Navigation Keys (left/right/up/down): Generally used to move the cursor or select the menu options or characters. 16.3 Descriptions of Input Methods 16.3.1 Handwriting Input Method Adopting advanced character recognition technology, your mobile phone supports the handwriting of numbers and English characters.
錯誤! 尚未定義樣式。 5. Click to input European symbol. 6. Click switch between capital and small letter. 16.3.3 English Input Method English input method includes abc input method and ABC input method. 1. Input English letters. Click the corresponding letters to input your desired word. 2.
Appendix 17.1 Special Functions As a type of multimedia mobile phone, your mobile phone not only supports the basic functions, but rich, practical, and quick multimedia functions as below: Analog TV You could use your mobile phone to watch TV. E-book Your mobile phone supports the display of txt format.
Page 83
錯誤! 尚未定義樣式。 Email Your mobile phone supports Email, which enables you to send/receive emails. Support the audio formats including midi, mp3 and amr etc. You could make different settings under Equalizer to get different sound effect. Sound Record Your mobile phone supports talk record and non-talk record Camera Your mobile phone support camera function.
Input Methods Your mobile phone supports multiple input methods, which enable users , to input Spanish letters English letters, numbers, symbols, etc. Handwriting input function provides you with much convenience. 17.2 Shortcuts lock the keypad In idle mode, hold key to quickly lock the keypad. Unlock the keypad In idle mode, press LSK and # key to unlock the keypad.
Page 85
錯誤! 尚未定義樣式。 Clean your mobile phone, battery and charger with a soft dry cloth. Do not clean your mobile phone with the liquor such as alcohol, dilution agent or benzene. Clean the socket from time to time because a dusty socket might cause disconnection, power failure, or even charging failure.
oven, toaster oven or radiator) because overheating might result in explosion. The color of the waterproof label in the phone will be changed if the phone or battery gets wet. In this case, the warranty provisions will become void even if the warranty period doesn’t expire. Please send your mobile phone to the nearest service center for inspection if there is anything wrong with your mobile phone, battery, charger or accessories.
錯誤! 尚未定義樣式。 Inadequate battery Charge the battery Unable to turn capacity on the phone Poor contact Reinstall the battery Automatic Seriously poor battery Recharge the battery capacity power-off Deceasing of battery Replace the battery performance Inadequate standby time Turn off the phone as the Poor network signal signal is poor.
Page 88
received, including interference that may cause undesired operation. This mobile phone has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 89
錯誤! 尚未定義樣式。 -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.
Page 90
4RF Exposure Information (SAR) This model phone meets the government’s requirements for exposure to radio waves. This phone is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR.
Page 91
FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid after searching on FCC ID: Q78-I766. For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines for use with an accessory that contains no metal and the positions the handset a minimum of 1.5 cm from the body.
Need help?
Do you have a question about the i766 and is the answer not in the manual?
Questions and answers