Glendo 004-895 Operation And Maintenance Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

ORIGINAL INSTRUCTIONS

#004-895

GraverSmith™

OPERATION AND MAINTENANCE MANUAL

READ THIS MANUAL ENTIRELY

BEFORE CONNECTING TO POWER.

following the instructions and maintenance in this manual.

NOTICE

This engraving system requires clean, dry, oil-free air. An oil-free compressor is

recommended for use with this system. For any oil‑type compressors, an oil‑removal filter

(coalescing type) in the air supply line to this engraving system MUST BE INSTALLED AND

IN USE.

For help with ordering or installing an oil‑removal filter, or for guidance with operation or

maintenance, please call GRS Technical Support at 800-835-3519 or +1-620-343-1084.

To send a request for assistance via electronic formats, e-mail support@glendo.com or visit:

Damage not covered by the warranty may result from not

OIL OR WATER CONTAMINATION

IS NOT COVERED BY WARRANTY.

http://www.grstools.com/customerservice/

Important notes are

highlighted in yellow

marked in red.

Table of Contents

Need help?

Do you have a question about the 004-895 and is the answer not in the manual?

Questions and answers

Summary of Contents for Glendo 004-895

Page 1 For help with ordering or installing an oil‑removal filter, or for guidance with operation or maintenance, please call GRS Technical Support at 800-835-3519 or +1-620-343-1084. To send a request for assistance via electronic formats, e-mail support@glendo.com or visit: http://www.grstools.com/customerservice/ highlighted in yellow Important notes are marked in red.
Page 2: Table Of Contents
Manual Contents Important Notice For Operators ......1 Required Equipment & Important Notes .....2 Introduction, Operation Note .
Page 3: Important Notice For Operators
IMPORTANT NOTICE FOR OPERATORS Read this manual thoroughly before operation. The manufacturer is not responsible for injury resulting from improper operation or when used by untrained operators. Do not modify this equipment or remove warning labels. Modifi cations can increase risks to the operator. Do not use this equipment if it is damaged.
Page 4: Required Equipment & Important Notes
READ THIS MANUAL ENTIRELY BEFORE CONNECTING TO POWER. Damage not covered by the warranty may result from not following the instructions and maintenance in this manual. REQUIRED EQUIPMENT & IMPORTANT NOTES Included 24-volt power converter • USE ONLY THE SUPPLIED 24-VOLT POWER CONVERTER. The included power converter may be connected to any properly grounded single-phase source of AC power within a voltage range of 100 to 240 V, 50 or 60 Hz.
Page 5 REQUIRED EQUIPMENT & IMPORTANT NOTES (continued) Clean, dry, oil-free air from an air compressor • Oil-free compressors are ALWAYS RECOMMENDED. When using an oil-lubricated compressor, install an oil‑removal fi lter (coalescing type – GRS #004‑579 or equivalent) in the air supply line to this engraving system. Damage due to oil or water contamination IS NOT COVERED BY WARRANTY.
Page 6: Introduction, Operation Note
FIG. 1 • GraverSmith™ Overview Front View Back View...
Page 7 The GraverSmith™ is an engraving system engineered and manufactured under the GRS Tools line of products by Glendo Corporation in the United States of America. This system is designed for assistance in creating unique works in metal, stone, wood, ivory, and many other materials.
Page 8 FIG. 2 • Mounting Air Filter to Side NOTE: If air supply 1. Remove top screw from hole. hose is larger than 1/4" (6.35 mm) OD, 2. Place screw through top hole either replace the on air ﬁ lter bracket. Tighten push-to-connect screw.
Page 9: Setup & Connections
SETUP & CONNECTIONS MOUNT & CONNECT AIR FILTER CONNECT HANDPIECE(S) Mount air fi lter in a location where the air Only one handpiece can be connected fi lter may be drained daily (see FIG. 2.A). and in operation at any time. Each Refer to FIG.
Page 10: Operation
OPERATION STROKES PER MINUTE (SPM) • Power on the air compressor and allow tank to fi ll. Wait for the Stroke speed is a matter of personal compressor to cycle off. preference and experience. The SPM dial (FIG. 4.A) settings are approximate and •...
Page 12 OPERATION (continued) HANDPIECE ADJUSTMENT TROUBLESHOOTING FIG. 6 The system will be diffi cult to control if the air pressure or SPM is incorrect. Use the lowest air pressure setting to provide proper operation; do not set the air pressure higher than needed. FOOT THROTTLE OPERATION •...
Page 13 OPERATION (continued) HANDPIECE OPERATION FIG. 7 Unlike traditional or push engraving where a fi rm grip and manual forward force is required, the GRS pneumatic handpiece requires only a light grip and guidance. Relax, allowing the engraving system to move the tool forward and through the material with guidance.
Page 14: Maintenance
MAINTENANCE FIG. 10 HANDPIECE Keep the handpiece clean for proper operation. Cleaning is necessary if operation becomes sluggish, erratic, or fails. Refer to FIG. 10 and the instructions below for the proper way to clean a handpiece. • Remove the piston and spring from the handpiece.
Page 15: Important Notices
IMPORTANT NOTICES GRS PROGRESSIVE FOOT CONTROL OWNERS The GRS Progressive Foot Control will operate properly with this engraving system. Attach the GRS Progressive Foot Control to the “THROTTLE CONNECTION” push‑to‑connect fi tting on the back of the system. AIR CONTAMINANTS AND WATER ACCUMULATION If large amounts of water and contaminants are in the air supply to the system, the bowl must be drained frequently to prevent water from entering the rotary valve, hoses, handpiece, etc.
Page 16: Service & Repair
Service & Repair Please call GRS or an authorized GRS dealer to order replacement parts and for instructions on replacement. Do not attempt to service parts that must be sent to GRS or an authorized GRS dealer; these must be repaired or replaced by GRS or an authorized GRS dealer.
Page 17: Parts Lists
15 15...
Page 18 16 16...
Page 19 17 17...
Page 20 18 18...
Page 21 19 19...
Page 24: Warranty
GraverMach™ AT, GraverMach™, GraverMax™ G8, GraverMax™ SC, GraverMax™, GraverMate™, GraverSmith™, BenchMate™, and Power Hone™ are trademarks of Glendo Corporation. Covered by USA and foreign patents. Printed in USA. Products made in USA. GraverMach™ AT, GraverMach™, GraverMax™ G8, GraverMax™ SC, GraverMax™, GraverMate™, GraverSmith™, BenchMate™, and ©...

This manual is also suitable for:

Graversmith