Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Holars AS Manuals
  4. IP Access Controllers
  5. H-TAG
  6. User manual

Holars AS H-TAG User Manual

Access controller / reader
Hide thumbs

Advertisement

Quick Links

Download this manual
H-TAG
Access Controller / Reader
User Manual
–
www.holars.no
www.holars.se

Advertisement

loading
Need help?

Need help?

Do you have a question about the H-TAG and is the answer not in the manual?

Questions and answers

Summary of Contents for Holars AS H-TAG

  • Page 1 H-TAG Access Controller / Reader User Manual – www.holars.no www.holars.se...

  • Page 2: Table Of Contents

    The H-TAG supports 600 users, it supports multi access modes in either card access, PIN access, Card + PIN access, or multi cards/PINsaccess. It has extra features including block enrollment, interlocked, Wiegand 26~37 bits interface...etc.
  • Page 3 4 bits, 8 bits(ASCII), 10 digits Virtual Number Environment Meets IP66 Operating Temperature C ~ 60 C (-40 F ~ 140 Operating Humidity 0%RH ~ 98%RH Physical Zinc-Alloy Enclosure Color Powder Coat Dimensions L150×W51×H23mm Unit Weight 500g Shipping Weight 650g Carton Inventory H-TAG Access Controller...

  • Page 4: Installation

    INSTALLATION Remove the back cover from the unit  Drill 2 holes(A,C) on the wall for the screws and one hole for the cable  Knock the supplied rubber bungs to the screw holes(A,C)  Fix the back cover firmly on the wall with 4 flat head screws ...
  • Page 5 (Master code is any 6 digits) 3. Exit Program Mode Set the Working Mode Notes: the H-TAG has 3 working modes: Standalone Mode, Controller Mode, Wiegand Reader Mode, choose the mode you use. (Factory default is Standalone Mode / Controller Mode) Programming Step Keystroke Combination 1.

  • Page 6: Standalone Mode

    STANDALONE MODE H-TAG can be worked as Standalone Reader for single door. (Factory default mode)---8 0 # Connection Diagram Common Power Supply: H-TAG Access Control Power Supply: H-TAG Door Bell Connect...
  • Page 7 * (Master Code) # Add Card User 2. Add Card: Using Auto ID 1 (Read Card) # (Allows H-TAG to assign Card to next The cards can be added continuously. available User ID number) 2. Add Card: Select Specific ID...
  • Page 8 Add Panic Users Programming Step Keystroke Combination 1. Enter Program Mode * (Master Code) # 2. Add Card: 1 (User ID) # (Read Card / Input 8/10 digits Card number) # 2. Add PIN: 1 (User ID) # (PIN ) # (User ID is any number from 598~599) 3.
  • Page 9 3. Exit Set Access Mode For Multi cards/ PINs access mode, the interval time of reading cards/inputting PINs can not exceed 5 seconds, or else, the H-TAG will exit to standby automatically. Programming Step Keystroke Combination 1. Enter Program Mode * (Master Code) # 2.
  • Page 10 Set Strike-out Alarm The strike-our alarm will engage after 10 failed card attempts (Factory is OFF). It can be set to deny access for 10 minutes after engaging or disengage only after entering a valid card/PIN or Master code. Programming Step Keystroke Combination 1.

  • Page 11: Controller Mode

    - There are some exceptions for your attention: H-TAG Connected with Enternal Card Reader: • If EM card reader or HID card reader: users can be added/deleted on either H-TAG or external reader. • If Mifare reader: users can only be added/deleted on external reader.
  • Page 12 H-TAG Connected with Fingerprint Reader: For example: Connect F2 as the fingerprint reader to H-TAG, it is of two steps to enroll the valid fingerprint. Step 1: Add the Fingerprint (A) on F2 Step 2: Add the same Fingerprint(A) on H-TAG:...

  • Page 13: Wiegand Reader Mode

    WIEGAND READER MODE H-TAG can work as Standard Wiegand Reader, connected to the third party Controller--- 8 1 # Connection Diagram H-TAG Notes: • When set into Wiegand Reader mode, nearly all settings in Controller Model will become invalid. And Brown & Yellow wires will be redefined as below:...

  • Page 14: Advance Application

    ADVANCE APPLICATION Interlock The H-TAG supports the Interlock funciton. It is of two keypads for two doors, and mainly used for banks, prisons, and other places where a higher level security is required. Connection Diagram: H-TAG H-TAG Remarks: The Door Contact must be installed and connected as the diagram.
  • Page 15 H-TAG - Simplified Instruction Function description Operation Enter the programming mode *- 123456 - # then you can do the programming (123456 is the factory default master code) 0 – new code - # - repeat the new code - #...