CONTENS Installation 3 DIN Front-Mount (Method A) Installing the unit Removing the unit DIN Rear-Mount (Method B) Using the detachable front panel 5 Specification 5 Wiring Connection 6 Location of keys 7 Basic operation 8 Release SEL and Vol control Power ON/OFF &...
INSTALLATION DIN FRONT-MOUNT (Method A) Installation Opening - Choose the mounting location where the unit will not inter This unit can be installed in any dashboard having fere with the normal driving function of the driver. an opening as shown below: - Before finally installing the unit, connect the wiring tempo rarily and make sure it is all connected up properly and the Installing the unit...
INSTALLATION 8. Slide the unit into the sleeve until it locks into place. and right sides of the unit, then pull the unit out of the dash- board. 9. To further secure the unit, use the supplied metal strap to secure the back of the unit in place.
FRONT PANEL TO DETACH THE FRONT PANEL SPECIFIATION 1. To remove the front panel from the unit chassis. press this key GENERAL to release the front panel from the unit chassis. then pull it up a little Supply Voltage : DC 12V.
WIRING T2 WIRING DIAGRAM AUX IN JACKS REAR FRONT RADIO ANTENNA GROUND(-) (BLACK) RCA LINE OUT LEFT (WHITE) +12V ACC/SWITCH (RED) RIGHT (RED) POWER ANTENNA LEFT (WHITE) AMPLIFIER TURN ON (BLUE) +12V CONSTANT POWER SUPPLY (YELLOW) RIGHT (RED) FRONT LEFT / WHITE+BLACK / - FRONT RIGHT / GRAY+BLACK / - FRONT LEFT / WHITE / + FRONT RIGHTT / GRAY / +...
BASIC 1. RELEASE BUTTON 5. POWER ON/OFF & MUTE Press the REL button to release the front control When the unit is power off, the unit comes to on panel from the unit chassis, then pull it up a little to by pressing any button except the EJECT remove from the unit chassis.
BASIC the radio execute the Preset scan. 11. CLOCK BUTTON 2) When short pressing, the radio searches for each Press the CLK button briefly to display time for 5 preset station in the current band and holds at that seconds on the display, and then returns to its previ- preset number for 5 seconds with releasing mute, and ous display unless the button is pressed again.
BASIC back of the SD/MMC card or USB stick. Press again to resume normal playback. CAUTION ! Press the INT button to play the first 10 seconds part of each track, and the LCD will display INT ON. When there are important files in the USB device, do Press again to stop scan, while the currently selected not connect it to the main unit to play.
REMOTE CONTROL FUNCTION KEYS & CONTROL Press it to pause the playback, press it again will resume the playback. 8. INT, 2 When playing MP3/WMA files, use it to select di- rectory upward, downward. 9. LOC Press it to enter LOCAL/DISTANT function. 10.
TROUBLE SHOOTING TROUBLE SHOOTING Before going through the checklist, check wiring connection. If any of the problems persist after checklist has been made, consult your nearest service dealer. SYMPTOM CAUSE SOPLUTION No power. The car ignition switch is not on. The car ignition switch is not on.
Page 14
SPECIFIATION GENERAL Supply Voltage : DC 12V. Negative Ground Supply Voltage : Max. 10A Current Consumption : 70watts x 4 Number of channels : 2 stereo channels Unit Dimensions : 178[W] x 101.5[D] x 50[H] mm RADIO For 2 Bands (Asia) Frequency Range : 87.5MHz - 108.0MHz...
Page 40
Corporation. 8th Floor, ACE HIGHTECH21 B/D, Digital Zone, Centurn City, 1470 U-dong, Haeundae-gu, Busan, Korea Published by DS international Corporation. copyright DS interationnal Corporation All right reserved.
Need help?
Do you have a question about the JB.lab T2 and is the answer not in the manual?
Questions and answers