Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for EasyGarage 30 inch WIDE TALL CABINET WITH DOORS/3 DRAWERS
- Page 1 Laminate Cabinet Installation Instructions www.EasyGarageStorage.com/Installation...
-
Page 2: Table Of Contents
Tools Thank you for your purchase! Please read each step of Hardware this manual thoroughly to ensure proper installation of Components your new EasyGarage storage solution. Cabinet Assembly Cabinet Installation These instructions assume that you are installing our Component Installation... -
Page 3: Tools
Instruction Guide Tools (subject to your storage solution) Hardware Kits (subject to your storage solution) Cabinet Install Kit (210440) Square Level Hammer Quick Dowel Bolt (Qty. 22) #2 Phillips #2 Phillips Back Saw Clamp Quick Dowel Insert (Qty. 22) Screw 2 1/2˝ (Qty. 6) Paper Towel Mallet Circular Saw... -
Page 4: Components
Instruction Guide Leg 6˝ Kit Leg 12˝ Kit Euro Screw Kit Drawer Adj. Screw Kit (4806) (4812) (210201/210203) (210213) (Qty. 12/24) (Qty. 10) (Qty. 1) (Qty. 1) Drawer Slide 18” Kit (5318) Screw 5/8˝ Kit Screw 1/2˝ Kit (210200/210209) (210300) (Qty. -
Page 5: Cabinet Assembly
Instruction Guide Cabinet Assembly Decks and cleats Push plastic quick dowel inserts into the ends of Lay verticals flat on floor. Screw metal quick dowel the cleats and decks. bolts into each vertical at location shown. Install decks Tap with mallet Make sure the white side is facing inward! Align Tap with rubber mallet until pieces are tight. - Page 6 Instruction Guide Install cleats Tap with mallet Align bolts and dowels, then push cleats down Tap with rubber mallet until pieces are tight. slightly to confirm alignment. Tap with hand to start connection. Install second vertical Tap with mallet Align bolts and dowels, then push vertical down Tap with rubber mallet until pieces are tight.
- Page 7 Instruction Guide Install 2 1/2˝ screws Install legs on base and tall cabinet Using provided square drive tip, install three (3) Rotate cabinet so it is laying on it’s back. Leg 2 1/2˝ screws through decks into cleats at each end installation is for base and tall cabinets only (not of deck.
-
Page 8: Cabinet Installation
Instruction Guide Cabinet Installation Determine cabinet locations Note your obstructions such as switches, plugs, Find studs with stud finder. Mark stud locations stem walls, garage door or track. Consider the with “X”. Confirm stud location by driving small nail configuration for stud support, as ideally, each into wall. -
Page 9: Component Installation
Instruction Guide Transfer stud locations Attach with 3 1/2˝ screws Inside cabinet, mark stud locations on cleats (a) Using a square drive tip, attach the cabinet to the at top and bottom of cabinet (a) and drill 1/8˝ pilot wood studs using 3 1/2˝ screws. Install screws into hole into center of cleats only (b). -
Page 10: Work Surface (Top) Installation
Instruction Guide Work Surface (Top) Installation Install top (continued) Confirm fit. Install tops using caulk (option 1) or Option 2 with screws: screws (option 2). Use clamps or tape to hold into place. Secure top to cabinet deck by installing 1 1/2˝ screws through Option 1 with caulk: underside of cabinet deck. -
Page 11: Fixed Shelf Installation
Instruction Guide Fixed Shelf Installation Install a fixed shelf (continued) Tall shelf or tall double door cabinets Drawer door tall combo cabinets Plan your layout based on your storage needs and Install the fixed shelf at the 24th visible hole from install the fixed shelf between 12˝... -
Page 12: Drawer Assembly And Installation
Instruction Guide Drawer Assembly and Installation Install a fixed shelf (continued) Lock fixed shelf. Holding the Philips screwdriver at Lay drawer box side flat. Place two drops of water a slight (15°) angle, lock fixed shelf with 1/4-1/2 turn or wood glue into dowel holes (a). Line up front of screwdriver. - Page 13 Instruction Guide Extend drawer slide Separate drawer slides Slides may be greasy. Use a paper towel or rag if Disconnect slide by moving lever down as the necessary. Pull slide outward. arrow shows and pull apart. Mark screw location Attach slides to box Using the provided template, bend template (a) Place slide onto drawer box and align holes with and hold front of template flush to front of box...
- Page 14 Instruction Guide Attach handle Install drawer in cabinet Using a hand screwdriver, attach handle to drawer Refer to drawer slide diagram below to front with screws provided, then attach front to determine slide location. drawer box. Top Deck Bottom Deck Top Deck Bottom Deck Install drawer in cabinet (continued)
- Page 15 Instruction Guide Install drawer in cabinet (continued) Install drawer in cabinet (continued) Pull ball retainers forward. Align drawer slide with cabinet slide. Gently press fully closed. Open and close drawer once to confirm connection. Repeat for remaining drawers Align fronts Starting with top drawer, use a screwdriver to slightly loosen drawer front screws (inside drawer).
-
Page 16: Adjustable Shelf Installation
Instruction Guide Adjustable Shelf Installation Place shelf onto shelf pins Determine location and insert shelf pins. Door Assembly and Installation Attach hinges to door Using two (2) #6 x 5/8˝ screws, attach hinge cup to Hook hinge into mounting plate (a) and snap to door. - Page 17 Instruction Guide Align Attach door Hold door in place. Hinge plate should align to Attach hinge to vertical. holes. Attach handle Adjust/align door up and down Attach screws through door into handle. Using a hand screwdriver, turn the adjuster screws to adjust door to desired position.
-
Page 18: Slatwall Installation With Molding
Instruction Guide Adjust/align door side to side Adjust/align door in and out Turn adjuster screws to adjust door to desired Turn adjuster screws to adjust door to desired position. position. Slatwall Installation with Molding Draw line Draw a level line at the lowest point you want the Find studs with stud finder. - Page 19 Instruction Guide Cut slatwall Install molding Measure and cut slatwall as needed with a saw Install frame molding around the perimeter and and thin sharp blade. Cut slowly and carefully. the seam molding between panel ends. Measure and cut the molding for either butt or miter joints. Attach with 2 1/2˝...
- Page 20 Instruction Guide Install remaining slatwall rows Install the frame molding at top Continue sliding remaining slatwall panels into the molding. Attach with screws. Slatwall Installation w/o Molding Draw line Draw a level line at the lowest point you want the Find studs with stud finder.
- Page 21 Instruction Guide Cut slatwall Install first slatwall panel Measure and cut slatwall as needed with a saw Place the first panel on this line (a). Level and and thin sharp blade. Cut slowly and carefully. plumb (b). Screw into wall studs using 2 1/2˝ screws with painted heads (c).
- Page 22 Instruction Guide Install Accessories Install accessories (continued) Snap badge onto accessory (a). Install accessory onto slatwall. Push plug into hole (b). Install magnetic tool bar Install magnetic tool bar (continued) Attach accessory clip to magnetic bar with bolt, Slip accessory clip into slatwall (a), slide up (b), and nut and cover.
- Page 23 Monday through Thursday: 8:00 AM to 7:00 PM EST Holland, MI 49424 Friday: 8:00 AM to 6:00 PM EST Saturday: 8:00 AM to 5:00 PM EST Se habla Español www.EasyGarageStorage.com Helpful information at EasyGarageStorage.com/Installation IDEAS? COMMENTS? Email to: Support@easygaragestorage.com © EasyGarage | ITEM #240010 | Rev. 09/17...