Silent Witness SW2300 User Manual

Full hd vehicle recorder

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

USER GUIDE

SW2300

FULL HD VEHICLE RECORDER

• Thank you for purchasing the SW2300 Vehicle Recorder.

• Please ensure that you read and understand this USER GUIDE

and use it before connecting and installing this Recorder.

• Please store the USER GUIDE in an easily accessible location.

VER 1.0.0 1st Edition

Table of Contents

Need help?

Do you have a question about the SW2300 and is the answer not in the manual?

Questions and answers

Summary of Contents for Silent Witness SW2300

Page 1 USER GUIDE SW2300 FULL HD VEHICLE RECORDER • Thank you for purchasing the SW2300 Vehicle Recorder. • Please ensure that you read and understand this USER GUIDE and use it before connecting and installing this Recorder. • Please store the USER GUIDE in an easily accessible location.
Page 2: Table Of Contents
INDEX ■Safety advice ................. ■GPS reception ................. ■Contents ................... ■Introduction ..................■Functions ..................■LEDs & Buzzer Specification ............■INSTALLATION ................■SOFTWARE USER GUIDE ............■SOFTWARE INSTALLATION ........... ■Initialize SD Card ................■Settings ..................■PC Viewer Software Viewing Settings........■Open the SD card .................
Page 3: Safety Advice
SAFETY ADVICE GPS RECEPTION Activate the product in an area without large buildings to CAUTION improve GPS reception. The commercial purpose GPS has the average rage error of more RISK OF ELECTRIC SHOCK than 15 meters and the range error could be more than 100 meters DO NOT OPEN due to environmental conditions like buildings, roadside trees etc.
Page 5: Contents
CONTENTS INTRODUCTION FRONT Bracket Camera Lens SW2300 Lock Vehicle Recorder Power Cable Memory Sticker for Windscreen mounting Wire Splice clips (x5) (double sided tape x1) Card Slot Left side Right Side...
Page 7: Introduction
INTRODUCTION FUNCTIONS Automatic Booting Once the SW2300 has been wired to your car power source the SW2300 will be boot up, this will take around 1 minute for the unit to be ready to record. BACK The default setting for record is the continuous recording at 30fps, 720P resolution.
Page 8: Leds & Buzzer Specification
A ‘Beep’ sound will occur when event recording starts (this can be turned off, if required by uncheck “Event Beep” at Settings) There are no time and date settings as the SW2300 gets this information from the GPS satellites. Status...
Page 10: Installation
Arrange the power cord neatly alongside of the windshield and door pillar trim. The VT1000 requires a continuous 12/24volt power source from the vehicle. The cable supplied will allow you to hard wire the SW2300 unit to the fuse box of your vehicle.
Page 11: Software Installation
SOFTWARE INSTALLATION INITIALIZE SD CARD The PC Viewer Software is on the provided SD card. (Also available on our website.) initialize SD Card’ Icon 1. Connect the SD card into your PC (if your computer does not have and SD card slot use the USB SD card reader) and open the “My Computer” 2.
Page 13: Settings
In custom set, you can set 3 different shock sensor values individually. Auto adjust G‐Sensor to Vehicle speed Once it checked, SW2300 will automatically decrease the G‐Sensor sensitivity at higher vehicle speeds to compensate for the naturally added G‐forces that are experienced due to velocity.
Page 15: Pc Viewer Software Viewing Settings
PC VIEWER SOFTWARE VIEWING SETTINGS Open the SD card Insert the SD card into your PC ① Click “Select SD Card” icon Viewing settings This setting is for the PC Viewer Software itself. To set the Recorder, refer to page 15. ②...
Page 16: Playback
Playback LOG FILE PLAYBACK Select [LOG] tap. Frame Size Check the log from the log list using mouse or click [Check All]. Then click [Load]. Resolution Record Mode Display Frame / Total frames number Log data Log data will be recorded during driving even if there are no events.
Page 17: Save Jpeg And Avi File
Save JPEG and AVI File Print Image Pause the playback and click “Print Image” icon. Pause the playback and click “Save JPG” icon to make JPG images. “Save JPG” icon “Print Image” icon Choose to print the current image or select another image from the same file you are in by searching the time and date.
Page 19: Backing Up Files
BACKING UP FILES GPS Log to KML Converter Select “Cont”, “Panic”. “Event”, “Log” tap and select the files first. To see the whole route on Google Earth, select the log file and click the Google Earth icon, as shown below. And then click the Backup icon to backup the files to the PC.
Page 20: Driver Report
Driver Report Analysis Criteria Settings Bottom Graph During the viewing, click the “Driver Report” icon to view the below Driver Report Screen. The lower graph shows the G‐sensors. The x‐axis is in red, y‐axis in blue, and z‐axis is green. “Driver Report”...
Page 22: Grading Criteria Settings
Analysis Criteria Settings Grading Criteria Settings Analysis Criteria Settings The criteria for grading driver’s safety and eco‐score can be set in these settings. This option allows you to make changes to the analysis criteria settings. To The safety and eco‐grading criteria have 7 and 8 separate components access this menu, go to ‘settings’...
Page 23 Grading Criteria Settings Grading Criteria Settings Acceleration Count Peak Speed Relative to Speed Limit (kmh/mph) This option sets the grading criteria the amount of times there is a sudden This option sets the grading criteria for speeding and calculates the peak speed acceleration per hour.
Page 25: Grading Method
Grading Method Graph Display Settings Grades: Each criteria is given a grade of A, B, C or D and anything lower is given a The results of the driver analysis can be shown on a graph. To adjust the graph grade of F for fail.
Page 27: Specification
SPECIFICATION APPENDIX - Recording time table Image sensor 1/3” 3 Megapixel CMOS Sensor 170° Angle of View 1080p HD (1920x1080) Video resolution 720P (1280x720), VGA (640x480) Recording Speed Up to 30 fps Continuous , Recording Mode Event (shock sensor, Panic button) Recording time See recording table below Memory...
Page 29: Appendix Upgrade
Copy “XXXXXX_x.x.x.bin” file to the SD card [program] folder. 2. Upgrade SW2300 Insert the prepared SD card to SW2300 unit and turn on the power. The Blue & Red LED will quickly blink while the unit is upgrading. It will also ‘beep’...