1. Manuals
  2. Brands
  3. SVP Manuals
  4. Media Converter
  5. HENM-70
  6. User manual

SVP HENM-70 User Manual

H.264 4:2:2 encoder & dvb-s2/s modulator
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
HENM-70
H.264 – 4:2:2
Encoder & DVB-S2/S Modulator
USER MANUAL V5.6

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HENM-70 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for SVP HENM-70

Summary of Contents for SVP HENM-70

  • Page 1 HENM-70 H.264 – 4:2:2 Encoder & DVB-S2/S Modulator USER MANUAL V5.6...
  • Page 2 Chapter 5: Web Server This chapter provides a detailed description of the Web Server tool. This feature allows the control of the HENM-70 encoder and DVB-S2/S modulator through a website. Chapter 6: Equipment Installation This chapter indicates the available connections of the HENM-70, their characteristics and the installation of the equipment.
  • Page 3 Dear customer, We would like to thank you for selecting this equipment and welcome you to the SVP’s growing family of products. We are sure that the addition of this equipment will cause you a complete satisfaction in your existing installation.

  • Page 4: About This Manual

    About this manual This user’s guide provides indications and explanations about how to set up easily the HENM-70 encoder & modulator for the most common use cases. This document is intended to help first time users: To find their way around the GUI.

  • Page 5: Important Notes

    3. This device has the ASI and IP output available when the input is ASI. Besides, it has also the ASI output available when the input is IP. 4. The HENM-70 encoder and DVB-S2/S modulator is available for L band. 5. In 1080p Video Format, it can only be performed the Standard Delay, not the Low Delay, Super Low Delay or Ultra Low Delay.
  • Page 6 7. In the case of injuries to the mouth, it may be necessary to use mouth-to-nose resuscitation. Seal the victim’s mouth with your cheek and blow firmly into his nose, proceeding as above. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 7 If help as available or as soon as resuscitation is no longer required the wound should be covered with a DRY clean dressing. d) Oil or grease in any form should not be applied. e) If severely burnt, get the victim to hospital immediately. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 8: Table Of Contents

    Main Index Chapter 1: Introduction ............... 4 Chapter 2: Technical Features .............. 7 Chapter 3: HENM-70 Operation and Menus ........... 10 Display .................. 10 3.1.1 Main Screen for the DVB-S2 ..........13 3.1.2 Main Screen for the DVB-S ..........15 Configuration Examples ............
  • Page 9 Connections ................. 113 6.2.1 Power supply ..............115 AC Power supply ..............115 DC Power supply ..............116 6.2.2 Intermediate frequency ........... 118 DVB-S2 output ................ 118 Intermediate frequency output IF ..........118 HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 10 Transport Stream over IP ..........121 Transport Stream over IP Input and Output ........ 121 6.2.6 Audio inputs ..............122 6.2.7 Data/GPS input ............... 124 6.2.8 USB connection .............. 125 6.2.9 Ethernet ................ 125 HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 11: Chapter 1: Introduction

    2150 MHz. A switchable 10 MHz reference signal is multiplexed on the L- band interface, providing a compact and cost effective solution for the up- converters which need external frequency reference. The HENM-70 has been designed to be used in broadcast and professional applications. HENM-70 Encoder & DVB-S2/S Modulator...
  • Page 12 70 a robust and reliable solution. DVB-S2 features In case the HENM-70 encoder & modulator is needed to be used as a satellite transmitter, it features an IF stage in the L band with an output power level from -50 to +5 dBm and a L band output that provides a 10 MHz reference oscillator.
  • Page 13 To sum up, with all of these characteristics, the maximum bit rate achieved is 31 Msym/s. DVB-S features The HENM-70 features an IF stage in the L band with an output power level from -50 to +5 dBm and an L band output that provides a 10 MHz reference oscillator.

  • Page 14: Chapter 2: Technical Features

    576i (720x576) – 50 Hz 480i (720x480) – 59.94 Hz Audio: Input: SDI embedded / HDMI embedded AES Digital / Analogue Analogue: 2 Stereo / 4 Mono Line, Micro Dynamic and Micro with Phantom HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 15 4/5, 5/6, 8/9, 9/10 Max. Symbol Rate: 31 Msymb/s Max. Bandwidth @ Rolloff: 0.35= 41.85 MHz Max. Bitrate: 89.732 Mbps DVB-S: QPSK Reed Solomon FEC: 1/2, 2/3, 3/4, 5/6, 7/8 Baud Rate: 31 Msymb/s HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 16 100 to 240V DC input: 8 to 36 V Consumption: 18W @ 12V Mechanical Size: ½ RU, 210x44x240 mm (WxHxD) Weight: 1,8 Kg Environmental Temperature range: -10 to 45 ºC Height: 4.500 m Humidity: HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 17: Chapter 3: Henm-70 Operation And Menus

    When a video, audio or data input has been selected, a character connected to this input is displayed in the main screen. Next, the main screen of the HENM-70 encoder & modulator is shown. Symbol Rate Frequency...
  • Page 18 Standard Delay (Lipsync < 10 ms) Low delay (Lipsync < 10 ms)  3 frames Super Low Delay (Lipsync < 10 ms)  2 frames Ultra Low Delay (Lipsync = 20 ms)  1 frame HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 19 Test Pattern Embedded Audio AES/EBU Analogue Test Tone RS232 Data Table 3.1 Linkages between the input and the character displayed Next, the main screen for each output type (DVB-S2 and DVB-S) is shown: HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 20: Main Screen For The Dvb-S2

    Data input selection (None, GPS, RS232, RS485 or UDP) and  (not darkened -> enabled / darkened -> disabled) and (static -> presence / blinking -> absence) Video Format (1080p, 1080i, 720p, 576i, 480i) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 21 53.300Mb Bitrate Modulation Scheme GEAD 576/50 420S Video Input Selection Latency Encoder Video Profile Audio Inputs Selection XXX/XX Data Input Selection Input Video Signal Format Figure 3.2 Main screen for DVB-S2 standard HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 22: Main Screen For The Dvb-S

    Data input selection (None, GPS, RS232, RS485 or UDP) and  (not darkened -> enabled / darkened -> disabled) and (static -> presence / blinking -> absence) Video Format (1080p, 1080i, 720p, 576i, 480i) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 23 QPSK 7/8 12.901Mb Bitrate Modulation Scheme 1080/50i 420L Video Input Selection Latency Encoder Video Profile Audio Inputs Selection XXX/XX Data Input Selection Input Video Signal Format Figure 3.3 Main screen for DVB-S standard HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 24: Configuration Examples

    420S XXX/XX blinking Figure 3.4 HENM-70 Main screen. Example 1 The Audio2 status indication is darkened because it is not enabled. If the Audio2 is enabled, then this field would not be darkened. When the data status field is enabled and blinkers, this means that there is nothing connected to the data input.
  • Page 25 1080/50 422S padlock XXX/XX Figure 3.5 HENM-70 Main screen. Example 2 The input selection is not blinking because the device is receiving SDI (S) video signal. The Audio1 and Audio2 status indications are not darkened because both of them are enabled. Letter ‘E’ corresponds to embedded and letter ‘A’ to analogue.
  • Page 26 Padlock: BISS activated  Encoder Video Profile: 4.2.0  Latency: Ultra Low Delay  F: 1360,500MHz DVBS P: +3.0 SR08.000 B10 QPSK 7/8 12.901Mb 1080/50i 420UL XXX/XX Figure 3.6 HENM-70 Main screen. Example 3 HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 27: Leds

    3.3 LEDs The HENM-70 transmitter has 4 Leds on its front panel that show the information detailed below. The ON/OFF provides the following information: If the Led is off, the equipment is not being fed.  If the Led flickers in red, there is power into the equipment but it is ...

  • Page 28: Front Panel

    3.4 Front panel The HENM-70 encoder and modulator is configured following a menus structure on the display. The front panel has 8 buttons to enter and exit the equipment control menus and submenus and to navigate through them. The function of each button is detailed in the following sections.

  • Page 29: Ok Button

    Figure 3.10 OK button 3.4.3 Cross Button This button is used to: Enter from the HENM-70 main screen to the setup menu and vice versa.  Exit equipment submenus.  This button allows the user to access to the main screen from the alarms ...

  • Page 30: Left And Right Button

    These buttons are also used to change, for example, the frequency and  PID parameters values. Pressing up and down arrows the value of those parameters can be changed, increased or decreased respectively. Figure 3.13 Up and Down buttons HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 31: Menus

    3.5 Menus There is one menu in this device that allows the operator to change the HENM-70 parameters and to configure them. To enter the menu of this equipment cross button must be pressed. In case it is wanted to return again to the principal screen from the menu, cross button must be pressed.
  • Page 32 Status Format Bitrate Bitrate Bitrate Bitrate IP.Adr Protocol Delay Delay Delay Bitrate Delay L Type Frequency Packet Size Profile Profile Profile Format BitRate Profile R Type Level Port Out.Delay TP per IP HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 33 Encoder continued continued Encoder Audio 2 Data Output Embedded Analogu AES-EBU Tone.Gen None None RS232 Bitrate Bitrate Bitrate Bitrate BaudRate Bitrate L Type Frequency Parity R Type Level Stop Bits HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 34 LDPC FEC Video PID TS id BISS-E Bandwidth Audio1 PID Network id Bandwidth Spectrum Roll Off 10 MHz Audio2 PID Network Name Pilots Antenna Gain Data PID Spectrum 10 MHz Antenna Gain HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 35 Keyboard Beep Temp Temperature Mask Keyboard Lock Restore Default DestinationIP &Port Voltage Gateway Night Mode Type Dist Units TP per IP Admin Pass Rectore Admin Pass Protocol User Pass Rectore User Pass HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 36: Menu Navigation

    3.5.1 Menu Navigation This section contains a detailed description of each parameter that can be configured in the HENM-70 encoder and DVB-S2/S modulator via the MENU. To enter the MENU, press the cross button in case of being in the main screen or in any submenu.

  • Page 37: Menu Structure

    IP Out – All the parameters related to the IP output are configured in this section. Unit – Parameters related to the Web Server and other internal options of the HENM-70 are configured here, as well as other characteristics. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 38: Encoder Menu

    Once the audio 1 input has been selected, press the OK button so as to configure the parameters related to it. The available options are: Embedded  Analogue  AES-EBU  Tone.Gen  None  HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 39 TS Parameters: This file consists on the configuration of the parameters of the Transport Stream. In this option, the different program identifiers are configured. Table 3.4 Encoder Menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 40: Sdi Input

    Profile: In this field, the codification profile can be configured. So as to select the desired profile, press Right, Left arrows buttons. (eligible parameter) The available options are: 4.2.2  4.2.0  HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 41 (1080p, 1080i, 720p). If other video input (SDI, CVBS or ASI) is selected, then the transmitter automatically captures its format and the frame rate. If the video format is changed, the time detection of this new format is less than 15 seconds. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 42: Hdmi Input

    Profile: In this field, the codification profile can be configured. So as to select the desired profile, press Right, Left arrows buttons. (editable parameter) The available options are: 4.2.0  4.2.2  HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 43 In this field, the group of figures parameter is displayed. It specifies the order in which intra- inter-frames are arranged. (eligible parameter) The available options are: Auto  Manual (editable parameter)  Table 3.6 HDMI Input menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 44: Cvbs Input

    Profile: In this field, the codification profile can be configured. So as to select the desired profile, press Right, Left arrows buttons. (eligible parameter) The available options are: 4.2.0  4.2.2  HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 45 In this field, the group of figures parameter is displayed. It specifies the order in which intra- inter-frames are arranged. (eligible parameter) The available options are: Auto  Manual (editable parameter)  Table 3.7 CVBS Input menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 46: Asi Input

    Format: In this field, the format of the ASI input signal is shown. (reading parameter) The available options are: 188 bytes  204 bytes  Table 3.8 ASI Input menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 47: Ip Input

    IP INPUT Port: 5600 Out. Delay: 128 ms TP per IP: 1 IP INPUT Status: ENABLE Protocol: UDP Packet Size: 188 IP INPUT BitRate: 0.00Mb PCR: No Present Figure 3.20 IP Input Menu HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 48 In case the signal is received from a multicast address, that multicast address must be configured in this field. So as to enter the multicast address, press the OK button so as to be able to configure the multicast address. (editable parameter) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 49 This field displays the number of TS packets per IP packet. (reading parameter) Status: This field displays the status of the IP input. (reading parameter) Protocol: This field displays the protocol used for the communication. (reading parameter) The possible options are:   HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 50 100 ms a Program Clock Reference, or PCR is transmitted in the adaptation field of an MPEG-2 transport stream packet. The parameters displayed can be present or no present. (reading parameter) Table 3.9 IP Input Select menu option HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 51: Generator Input

    In this field, the group of figures parameter is displayed. It specifies the order in which intra- inter-frames are arranged (eligible parameter). The available options are: Auto  Manual (editable parameter)  Table 3.10 Generator Input menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 52: Audio1 Embedded

    Table 3.11 Audio Embedded Input menu options If the video option selected is CVBS, ASI, IP or Test Pattern generator then, the option of audio embedded will be blinking because that configuration is not possible. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 53: Audio1 Analogue

    So as to choose the type of audio 1, press Right, Left buttons. (eligible parameter) The available options are: Line  Mic Dynamic  Mic Phantom  Table 3.12 Audio Analogue Input menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 54: Audio1 Aes-Ebu

    So as to select the desired bitrate, press Right, Left arrows buttons. (eligible parameter) The available options are: 128K  192K  256K  384K  Table 3.13 Audio AES-EBU Input menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 55: Audio1 Tone.gen

    In this field, the frequency of the generated tone is displayed. (reading parameter) Level (dBFs): In this field, the level in dBF of the generated tone is displayed. (reading parameter) Table 3.14 Audio Generator Input menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 56: Audio2 Embedded

    Table 3.15 Audio Embedded Input menu options If the video option selected is CVBS, ASI, IP or Test Pattern Generator then, the option of audio embedded will be blinking because that configuration is not possible. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 57: Audio2 Analogue

    So as to choose the type of audio 2, press Right, Left buttons. (eligible parameter) The available options are: Line  Mic Dynamic  Mic Phantom  Table 3.16 Audio Analogue Input menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 58: Audio2 Aes-Ebu

    So as to select the desired bitrate, press Right, Left arrows buttons. (eligible parameter) The available options are: 128K  192K  256K  384K  Table 3.17 Audio AES-EBU Input menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 59: Audio2 Tone.gen

    In this field, the frequency of the generated tone is displayed. (reading parameter) Level (dBFs): In this field, the level in dBF of the generated tone is displayed. (reading parameter) Table 3.18 Audio Generator Input menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 60: Data

    Latitude of the Speed(knot)/ Direction(degrees) HENM-70 #--º--.---´ ---k ---º Longitude of the Height (meters) #---º--.---´ -----mt HENM-70 Satellite Level --/--/-- Date Level of the satellite signals --:--:-- Time Figure 3.31 GPS screen HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 61 Latitude of the HENM-70: It specifies the latitude position of the device.  Speed of the HENM-70: It shows the speed of the HENM-70 in knot.  Direction of the HENM-70: The direction of the device is shown in this field.
  • Page 62 (Parity options are None, Even, Odd) (eligible parameters) Stop Bits: Select the same number of stop bits as the received data user signal has. (Stop bit options are 1 or 2) (eligible parameter) Table 3.19 Data Parameters HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 63: Encoder Output

    (modulation scheme, FEC) then, in the main screen the line (third line) in which these parameters (modulation scheme, FEC, bitrate) appear blinks. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 64: Ts Parameters

    (editable parameter) Audio2 PID: Here the audio2 packet identifier must be entered. So as to change its value first, press the OK button and then, with the UP, Down HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 65 With the Right, Left keys, the user can select the character of the word. Press the OK button so as to save the introduced value. (editable parameter) Table 3.21 Encoder TS menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 66: Ca-Biss Menu

    In this field, the SW password must be introduced, which is valid for BISS-1 and BISS-E encryption. (editable parameter) User: In this field, the User password must be introduced, which is valid only for BISS-E encryption. (editable parameter) Table 3.22 CA-BISS menu option HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 67: Modulator Menu

    The BISS encryption is activated in the modulator and in the ASI output. 3.5.2.3 Modulator Menu By using the Up, Down arrow keys, select the Modulator option and press the OK key. MODULATOR DVB-S2 >DVB-S Figure 3.36 Modulator Menu HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 68: Dvb-S2

    So as specify the output power, select it in the power option) Modulator (The RF output carrier with modulation. So as specify  the output power, select it in the field below) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 69 In this field, the value of the output power can be selected. The possible output power range is from -20 to 5 dBm. (editable parameter) L-BAND (The output power of the HENM-70 in dBm)  HPA (The output power of the amplifier in dBW) ...
  • Page 70 Here the type of the spectrum is configured. Inverted spectrum is just another method to help preventing signal theft. Use Right and Left buttons so as to select the desired option. (eligible parameter) The available options are: Normal  Invert  HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 71: Symbol Rate Calculation

    Next, it is shown a table as an example of the Symbol Rate values for a determined Bandwidth of 28 MHz. Bandwidth (MHz) Roll-off Symbol Rate (Msymb/s) 0.20 23.33 0.25 22.4 0.35 20.74 Table 3.24 Symbol Rate calculation HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 72: Dvb-S

    So as specify the output power, select it in the power option) Modulator (The RF output carrier with modulation. So as specify  the output power, select it in the field below) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 73 In this field, the value of the output power can be selected. The possible output power range is from -20 to 5 dBm. (editable parameter) The available options are: L-BAND (The output power of the HENM-70 in dBm)  HPA (The output power of the amplifier in dBW) ...
  • Page 74 Antenna Gain (dBi): Select the gain of the transmitter antenna. Press the OK button to configure it and then the OK button again to save the introduced value.(editable parameter) Table 3.25 DVB-S menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 75: Ip Out

    So as to change from one character to another, press Right, Left keys. So as to save the value, press the OK button. (editable parameter) MAC ADDRESS The MAC Address of the transmitter is shown. (reading parameter) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 76 OK button and then, with the Up, Down, and Right, Left buttons select the desired value. So as to save the value, press OK button. (editable parameter) Table 3.26 IP Out menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 77: Unit Menu

     ASI Overflow: this alarm means that the input bitrate is higher than the one that can be modulated due to the parameters configured (constellation, FEC, GI...). The different warnings that can appear in the device are:  No Video Input.  No GPS. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 78: Monitor

    (values from 0 to 3) where 0 means that the fans are stopped and value 3 is the maximum speed. (reading parameter) Voltage:  In this field, the voltage of the device is shown. (reading parameter) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 79: Webserver & Snmp

    Right and Left keys. Press the OK button so as to save the introduced value. (editable parameter) MAC ADDRESS (Reading parameter) In this field, the MAC address of the device is shown. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 80 Finally press OK button to save the introduced values. Restore User Pass: This option enables restore default user password (00000000). Table 3.27 Webserver & SNMP menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 81: Miscellaneous

    1. If the state is three then, the light in the screen will be the lowest of the four possible states. (eligible parameter) The available options are:     HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 82  S/N: In this field the serial number of the device is shown (reading parameter). MAC Address: The MAC Address of the transmitter is shown. (reading parameter) Table 3.28 Miscellaneous menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 83: Firmware

    The rest of the characters are important for the manufacturer but are not important for the user. Table 3.29 Firmware menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 84 Next, the necessary steps so as to make a successful update are explained. The latest firmware is allocated in the webpage of SVP Broadcast Microwave. So as to access to the firmware file, first enter www.svpbm.com in your web browser.
  • Page 85 To verify the version of the device, go to firmware field and then look at the Rv option to check the number of the version installed in the device (the first two digits). Figure 3.48 Updating firmware step 5 HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 86 Now, automatically the device updates the firmware. The screens which are shown below display the different steps that the device is making while the updating process. Don’t power off the device during the updating process. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 87: Buc S/S2 Unit

    In this option, the temperature of the BUC is shown in the screen. Type: In this option, the type and the model of the BUC is shown in the screen. The available options are:  WAVE  Table 3.30 BUC S/S2 Unit menu options HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 88: Chapter 4: Gps Application

    Chapter 4: GPS Application 4.1 Introduction The HENM-70 encoder and modulator has a GPS antenna input in order to give information to the device about the positioning data. The connexion of the GPS antenna to this input, allows the transference of the information given.

  • Page 89: Gps Transmitter Screen

    Longitude of the HENM-70: It specifies the longitude position of the device.  Speed of the HENM-70: It shows the speed of the device in knot.  Direction of the HENM-70: The direction of the device is shown in this field.

  • Page 90: Gps Ird-70 Decoder Screen

    Longitude of the Distance from receiver to transmitter/ transmitter Direction from transmitter to receiver(degrees) Rec Coords: #---º--.---´ #---º--.---´ Coordinates of Latitude of Longitude the receiver of the receiver receiver Figure 4.4 GPS receiver screen HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 91 Longitude of the receiver: In this field the user can enter the longitude of the receiver.  Latitude of the receiver: In this field the user can enter the latitude of the receiver. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 92: Application Example

    GPS antenna IRD-70 Demodulator & Decoder With the GPS antenna connected to the HENM-70, positioning of the device is achieved once the GPS system is connected to the necessary satellites. Data obtained in the transmitter is the positioning of the device.
  • Page 93 IRD-70 Demodulator & Decoder RS232 connection Video Transmitter System PC with Google Earth E20º45.512´ 10k47º1mt 04/10/13 N60º73.984´ S3 100km 100º 09:45:34 IRD-70 GPS screen Receiver System Figure 4.5 GPS system example picture HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 94: Chapter 5: Web Server

    Up, Down keys select the desired number. So as to change from one character to another, press Right, Left keys. Press the OK button so as to save the introduced value. UNIT ETHERNET LOC 192.168.001.010 MSK 255.255.000.000 GAT 192.168.001.001 Figure 5.3 Subnet Mask HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 95 User Pass must be set to 0 (00000000). However, if it is wanted to set a user’s password, it is necessary to introduce 8 digits. In this way, with this password, the user can access to the Webserver and make any monitoring. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 96: Web

    Figure 5.8 Restore User Pass Once the IP, Subnet Mask, Gateway, User Password and Admin Password are set and the laptop or PC is connected to the HENM-70, open the web browser and tip the IP given to the device.

  • Page 97: Encoder

    TSoIP screen. (eligible parameter) - Format: Here the format of the video input signal is displayed. If there is no video input then the message ‘not detected’ is displayed. (reading parameter) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 98: Audio

    128, 192, 256 and 384 Kbps. (eligible parameter) - [A2] Input: Select the type of signal introduced in the audio 2 input. The audio input options available are Embedded, Analogue, AES-EBU, Test Tone and None. (eligible parameter) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 99: Data

    Select the parity for the RS-232 connection. The available options are None, Odd and Even. (eligible parameter) - Stop Bits: Establish the number of stop bits for the RS-232 connection. The available options are 1 and 2. (eligible parameter) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 100: Gps

    - Direction: The direction in degrees of the transmitter is shown in this field. (reading parameter) - Speed: The speed of the transmitter in km/h is shown in this field. (reading parameter) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 101: Ts Parameters

    In this field the Transport Stream identifier must be set. (editable parameter) - Network id: In this option the network identifier must be specified. (editable parameter) - Network Name: Specify the name of the network. (editable parameter) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 102: Output

    FEC, IG, BW used, so as to the video bitrate can be always the maximum allowed. SVP advises to use the automatic mode when the signal is transmitted through RF.

  • Page 103: Mod_Rf

    DVB-S2 and DVB-S. (eligible parameter) - RF Status: Select On in case of wanting to activate the RF transmission or press Off button so as to deactivate it. (eligible parameter) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 104: Dvb-S2

    (LDPC FEC options are: 1/4, 1/3, 2/5, 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9, 9/10) (eligible parameter) - Symbol Rate: In this field the value of the symbol rate of the transmitted signal can be selected. (From 2 to 45Mbaud/s) (editable parameter) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 105 When the enter button is pressed, the new values are saved and the text will appear in black colour. It is necessary to press the enter button to keep and save the new values on the screen. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 106: Dvb-S

    Specify the transmission mode which can be no output. (eligible parameter) The available options are:  Low Carrier  Carrier  Modulator ON - Power: Specify the power at which the signal is being transmitted. (editable parameter) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 107 When the enter button is pressed, the new values are saved and the text will appear in black colour. It is necessary to press the enter button to keep and save the new values on the screen. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 108: Tsoip

    Configure the Subnet address of the device which is going to send the information. (editable parameter) Gateway: Configure the Gateway address of the device which is going to send the information. (editable parameter) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 109: Ip Output

    When the enter button is pressed, the new values are saved and the text will appear in black colour. It is necessary to press the enter button to keep and save the new values on the screen. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 110: Ip Input

    Configure the Subnet address of the device which is going to receive the information. (editable parameter) Gateway: Configure the Gateway address of the device which is going to receive the information. (editable parameter) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 111 In this field it is displayed the size in bytes of the IP received packet. (reading parameter) TP per IP: In this option the number of Transport Stream packets per IP packet is displayed. (reading parameter) HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 112 When the enter button is pressed, the new values are saved and the text will appear in black colour. It is necessary to press the enter button to keep and save the new values on the screen. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 113: Ca-Biss

    When the enter button is pressed, the new values are saved and the text will appear in black colour. It is necessary to press the enter button to keep and save the new values on the screen. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 114: Unit

    5.2.5 UNIT Figure 5.16 Web Server Unit screen HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 115: Leds Status (Reading Parameters)

    (constellation, FEC, GI...). The different warnings that can appear in the device are: No Video Input. No GPS. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 116: Configuration

    In this field, the user’s password is introduced. It can be set an own password which is a list of 8 digits. Then, to save the introduced value, press Enter button. Moreover, there is the option to restore the default user password (00000000). HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 117: Monitor

    When the enter button is pressed, the new values are saved and the text will appear in black colour. It is necessary to press the enter button to keep and save the new values on the screen. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 118: Web Page Setup Notes

    SNMP is an application-layer protocol and it runs over UDP at the transport level. SNMP is based on a manager / agent model as it is shown below: HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 119: Snmp Commands

    Station SNMP agent Figure 5.17 SNMP management system The SNMP agent used is MIB-II compliant. The SVP MIB (Management Information Database) provides a standard representation of the SNMP Agent’s available information and where it is stored. The MIB is defined according to the ASN.1.

  • Page 120: Chapter 6: Equipment Installation

    HENM-70 and their pinout, connectors needed and the accessories which are available with the device. 6.2 Connections Every connection of the HENM-70 encoder and modulator is on the rear panel. All the Lemo part numbers and pinout refer to the connector that is fixed to the cable.
  • Page 121 Figure 6.3 HENM-70 rear panel Technical features of each connection are described on the following sections. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 122: Power Supply

    Power supply AC connection technical features Item Features Connector label POWER A.C. Connector type MLC Neutrik Supply voltage 100-240 V. (50/60Hz) Table 6.1 AC Power supply features Pinout HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 123: Dc Power Supply

    NAC3MPA DC Power supply The HENM-70 equipment can be powered by a DC source from 8 to 36 V. The DC power supply is connected via a Neutrik 4-pin male XLR connector with a safety clip to prevent accidental disconnection.
  • Page 124 Pinout Description Table 6.4 DC Power supply connector pinout Connector needed The DC power supply is connected via a Neutrik 4-pin male XLR connector with a safety clip to prevent accidental disconnection. HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 125: Intermediate Frequency

    The HENM-70 can be connected to a Block-Up-Converter connecting the IF Input of the BUC to the IF out (L-band) connector of the HENM-70, and the M&C connector of the BUC to the DATA GPS connector of the HENM-70, as shown in the figure below.

  • Page 126: Asi

    ASI output signal type uses 75Ω BNC connector. This connector is placed on the HENM-70 encoder rear panel. It is important that 75 Ω connectors are used. This is because the female output connector of the HENM-70 unit may be damaged and because of an impedance mismatch. ASI connection technical features...

  • Page 127: Cvbs/ Sdi/ Hdmi

    SMPTE-292 compliant and 3G-SDI digital video input signal type is SMPTE-425M compliant. In chapter 3: HENM-70 Menus and Operation, it is explained in detail how to choose the input video signal type, CVBS, HDMI, digital video SDI signal, DVB-ASI Transport Stream signal or IP input.

  • Page 128: Transport Stream Over Ip

    6.2.5 Transport Stream over IP Transport Stream over IP Input and Output The HENM-70 encoder has a connector that allows receiving and transporting video over IP. The connector is an UTP Cat 5e which is described in the EIA/TIA568B standard.

  • Page 129: Audio Inputs

    6.2.6 Audio inputs The HENM-70 encoder and modulator has four possible audio inputs: 2 audio inputs to insert 2 AES/EBU stereo channels, 2 stereo or 4  mono analogue (mic phantom, mic dynamic and line) signals where connections are made using two 5 pin Lemo 0B connectors on equipment’s rear panel.
  • Page 130 Pinout of the cable connector (Watched from the soldering side) Description A1L+ / AES1P A1L- / AES1N A1R+ A1R- Table 6.14 AES/EBU and analogue audio cable connector pinout HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...

  • Page 131: Data/Gps Input

    Thanks to this characteristic it is possible to obtain GPS coordinates in the HDR-106 receiver or in the HDE-70 decoder and to know the exact position of the HENM-70 and the distance between the receiver and the transmitter as well as other parameters.

  • Page 132: Usb Connection

    6.2.8 USB connection Thanks to the USB connection, it is possible to update directly from an external USB device the firmware of the HENM-70 device. The connector is type A. USB connection technical features Item Features Connector Label Connector type Type A Table 6.17 USB connection technical features...
  • Page 133 Conditional Access-BISS COFDM Coded Orthogonal Frequency Division Multiplexing Direct current DVB-S2 Digital Video Broadcasting by Satellite – Second Generation ETSI European Telecommunications Standards Institute Error Vector Magnitude Forward Error Correction Fast Fourier transform HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 134 Interval Guard Internet Protocol Liquid Crystal Display Light-Emitting Diode Low Delay MPEG Moving Picture Experts Group NLOS Non Line of Sight Phase Alternating Line Packet Identification QPSK Quadrature Phase-Shift Keying RadioFrequency Remote Control HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 135 Standard Delay Serial Digital Interface SNMP Simple Network Management Protocol Thin-Film Transistor Transport Stream User Datagram Protocol Universal Serial Bus HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 136 Notes HENM-70 Encoder & DVB-S2/S Modulator USER’S MANUAL V5.6...
  • Page 137 Final note SVP Broadcast Microwave S.L. is constantly striving to improve all of its products. Therefore, we ask you to understand that modifications may occur in designs, equipment and technology. Consequently, no responsibility can be derived from the information, illustrations or descriptions contained in this manual.
  • Page 138 SVP Broadcast Microwave reserves the right to make changes to this manual and to the equipment without prior notice. C/ Zubiaurre 7 bajo 48215 Iurreta Vizcaya – Spain Tel: (+34) 94620 3722 info@svpbm.com www.svpbm.com...

Table of Contents