Table of Contents
Advertisement
Quick Links
TI-45N Operating Instruction Guide
N
OTES
24
TI-45N Operating Instruction Guide
OI503-45N
T
ABLE
1.0
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.0
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.0
Description of Gauge . . . . . . . . . . . . . . . . . . . . . . . . . .
4.0
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Installing the Battery
4.3 Connecting the Probe
4.4 Turning the Power On
4.5 Turning the Power Off
4.6 Using the Built-in Calibration Disc
4.7 Using Couplant Fluid
5.0
Quick Start Instructions - Steel . . . . . . . . . . . . . . . . . .
6.0
Overview Of Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3 Set-up for Measuring Thickness of Materials Other Than Steel
6.4 Acoustic Velocity Selection Table
6.5 Setup of Gauge When Acoustic Velocity is Unknown
6.6 Changing Acoustic Velocity Settings
6.7 Changing Modes
7.0
Taking Measurements . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1 Notes on Measurements
7.2 Preparing the Surface For Measurement
7.3 Measurement of Pipes or Cylindrical Objects
8.0
Trouble-Shooting Guide . . . . . . . . . . . . . . . . . . . . . . . .
9.0
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
O
C
F
ONTENTS
1
02
03
04
06
08
10
16
19
21
22
23
Advertisement
Table of Contents
Summary of Contents for ELECTROMACTIC Equipment Co., Inc. CHECK-LINE TI-45N
-
Page 1: Table Of Contents
TI-45N Operating Instruction Guide TI-45N Operating Instruction Guide OI503-45N OTES ABLE ONTENTS Introduction ........Precautions . -
Page 2: Introduction
TI-45N Operating Instruction Guide TI-45N Operating Instruction Guide ARRANTY NTRODUCTION The CHECK•LINE TI-45N Thickness Gauge measures the wall thickness of metals, ® ELECTROMATIC Equipment Co., Inc. (ELECTROMATIC) warrants to the glass, ceramics and many rigid plastics. This gauge uses the “pulse-echo“ principle original purchaser that this product is of merchantable quality and confirms in of ultrasonic testing where a short ultrasonic signal is transmitted from the probe. -
Page 3: Precautions
TI-45N Operating Instruction Guide TI-45N Operating Instruction Guide RECAUTIONS PPENDIX 1. The probe surface is fabricated from acrylic resin and care should be taken to The TI-45N Thickness Gauge is supplied from the factory set for an acoustic velocity insure that it is not scratched by sliding over rough surfaces. The probe should of 5930 m/sec for the measurement of steel. -
Page 4: Description Of Gauge
TI-45N Operating Instruction Guide TI-45N Operating Instruction Guide PECIFICATIONS ESCRIPTION OF AUGE Range (steel) Flat plate 1.00 to 199.99mm 3.1 Gauge Pipe 30 in. diameter and 1.50 in. thickness or more Accuracy (mm) ±0.02 Errors (mm) 1.00 to 99.9 ±0.05 100.00 to 199.99 ±2% / rdg Probe Cable Connectors Red: transmitter... -
Page 5: Units Of Measure
TI-45N Operating Instruction Guide TI-45N Operating Instruction Guide 3.3. Complete Kit Description of Problem Possible Cause Action To Be Taken Carrying Case Fluxuating readings Defective probe Return to manufacturer Fluxuating readings while Aluminum measurement Switch to aluminum mode measuring aluminum is being taken in standard mode Coupling Fluid... -
Page 6: Getting Started
TI-45N Operating Instruction Guide TI-45N Operating Instruction Guide 8.0 T ETTING TARTED ROUBLE HOOTING UIDE 4.1 Setting Units Of Measure Description of Problem Possible Cause Action To Be Taken Remove the Battery Cover on the back side of the gauge Inch by pressing it down with your thumb and sliding it in the Gauge will not power... - Page 7 TI-45N Operating Instruction Guide TI-45N Operating Instruction Guide 7.3 Measurement Of Pipes Or Cylindrical Objects 4.4 Turning The Power ON When using a TI-45N Gauge to measure the wall thickness of pipes it is After connecting the probe as described in section 4.4, turn on the power by highly recommended that the optional spring-loaded shell attachment be used.
-
Page 8: Quick Start Instructions - Steel
TI-45N Operating Instruction Guide TI-45N Operating Instruction Guide 7.1 Notes On Measurements UICK TART NSTRUCTIONS TEEL HICKNESS 1. The following surface conditions can prevent accurate measurements. These Quick Start procedures are intended for those applications where the thickness of (Refer to section 7.2 Preparing The Surface For Measurement.) steel is to be measured. - Page 9 TI-45N Operating Instruction Guide TI-45N Operating Instruction Guide AKING EASUREMENTS OTES After setting the gauge for the correct acoustic velocity for the material to be measured a. When the probe is removed from the sample after a measurement, the last reading or retaining the factory preset value of 5930 m/sec for measurement of steel, the gauge will be stored.
-
Page 10: Overview Of Modes
TI-45N Operating Instruction Guide TI-45N Operating Instruction Guide 6.7 Changing Modes 6.0 O VERVIEW OF ODES Flow of mode selection: The TI-45N has several modes which are used for operation and velocity adjustment as described below. Each time the MODE key is pressed, the gauge will toggle from one S to B 1 measurement method mode to the next as shown in the sequence below: Standard... -
Page 11: 6.1 Acoustic Velocity Modes
TI-45N Operating Instruction Guide TI-45N Operating Instruction Guide 6.5 Setup Of Gauge When Acoustic Velocity Is Unknown 7. Press MODE key. Returns to this Measurement mode. In applications where the type of material is not known or the material type is not listed in the Acoustic Velocity Selection Table the following steps can inch 6.1 Acoustic Velocity Modes... - Page 12 TI-45N Operating Instruction Guide TI-45N Operating Instruction Guide 6.3 Setup For Measuring Thickness Of Materials Other Than Steel 6.4 Acoustic Velocity Selection Table The TI-45N Thickness Gauge is supplied from the factory set for an acoustic velocity of 5930 m/sec for the measurement of Steel. To measure the thickness of ACOUSTIC VELOCITY SELECTION TABLE any other material, the acoustic velocity must be changed.
- Page 13 CHECK LINE ® • BY ELECTROMATIC TI-45N Operating Instructions Guide Distributed by: ABQ Industrial LP USA Tel: +1 (281) 516-9292 / (888) 275-5772 eFax: +1 (866) 234-0451 Web: https://www.abqindustrial.net E-mail: info@abqindustrial.net...
Need help?
Do you have a question about the CHECK-LINE TI-45N and is the answer not in the manual?
Questions and answers