SP5293 Fornitor XL USER MANUAL Please carefully check the unit and make sure there is no damage when you open the carton. QUESTIONS, PROBLEMS, OR MISSING PARTS? Please Contact Customer Service Before Returning to Store www.soupro.com cs@soupro.com +1-800-239-0689 Keep this manual for future reference...
Table of Contents • GENERAL INFORMATION FCC/ICSES Information Safety Instructions Warranty • ASSEMBLY INSTRUCTIONS Preparation Assembly • FIREPLACE OPERATIONS Operating Instructions Care And Maintenance Troubleshooting FCC / ICES Information This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to part 15 of the FCC rules.
• To prevent a possible fire, DO NOT block any air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where opening may become blocked. • ALWAYS plug this unit directly into a wall outlet/receptacle. NEVER use with an extension cord or relocatable power tap (outlet/power strip).
Warranty 1-YEAR LIMITED WARRANTY Source Pro USA Inc. (hereinafter referred to collectively as “the Company”) warrants that your new Bold Flame Electric Fireplace is free from manufacturing and materials defects for a period of one (1) year from date of purchase. Subject to the following conditions and limitations: The electric fireplace must be installed and operated at all times in accordance with the installation and operating instructions furnished with the product.
Preparation IMPORTANT INFORMATION 1. Before you begin, locate the instructions and hardware. Be sure you have all of the parts and can identify them. 2. To avoid scratching the finish, assemble the product on a soft, non-abrasive surface such as carpet or cardboard.
Page 6
Preparation Parts List Front Glass Cover Mounting Bracket Base Remote Control Fireplace Rocks...
Assembly - Wall Mount Installation Remove mounting bracket (D) from back of fireplace (C) by unscrew two screws at the top of the unit. Release the latches on the both side to unlock the front glass as illustrated below. Carefully pull the front glass (A) slightly away from the fireplace (C) and set down.
Page 8
Assembly - Wall Mount Installation Remove the base (B) of fireplace (C) by unscrewing three screws at the rear base of the unit. Choose a wall location to attach the mounting bracket (D). Position the mounting bracket (D) in the desired location. Use a level to align the bracket and mark the four holes with a pencil.
Page 9
Assembly - Wall Mount Installation Select the hardware appropriate for mounting bracket installation. STUD WALL • Secure the mounting bracket (D) to wall using screws (AA) at marked stud locations. DRYWALL • Drill holes at marked locations and secure the mounting bracket (D) to the wall with toggle bolts and washers (not included).
Page 10
Assembly - Wall Mount Installation Distribute the rocks (F) evenly in the tray of the fireplace (C). Re-install the front glass (A) to the fireplace (C), and connect the mood light cable.
Assembly - Free Standing Installation Assembly the base (B) of fireplace (C) by fasten three screws. Release the latches on the both side to unlock the front glass as illustrated below. Carefully pull the front glass (A) slightly away from the fireplace (C) and set down. Then gently pull the release tab on the cable and finish removing front glass (A).
Page 12
Assembly - Free Standing Installation Distribute the rocks (F) evenly in the tray of the fireplace (C). Re-install the front glass (A) to the fireplace (C), and connect the mood light cable.
Operating Instructions ° F ° C Power Button Setting color Setting color • Press the POWER button to turn ON or OFF the unit. Purple • When the unit is in ON mode, touch control panel light Orange White will fully light up for 8 sec and then shut down if without Yellow Above 8 colors any others operation including remote control.
child lock up Button ; Down Button • Control the setting of flame brightness, flame color, activate child lock mood light brightness, mood light color, timer, clock and • When the unit is ON, hold the POWER button for 10 temperture . seconds to activate the Child Lock function. "E3" will be displayed and a "beep" will sound 3 times to indicate the Child Lock function is activated. Then, all function keys are locked. When pressing any button, "E3" will be displayed to indicate the Child Lock function has been activated. Deactivate child lock • To deactivate the Child Lock function, hold the POWER button for 10 seconds. Then, all functions keys are unlocked.
Care And Maintenance DISPOSAL OF USED BATTERY: A battery may contain hazardous substances that could be endangering to the environment and human health. • This symbol marked on the battery and/or packaging indicates that used battery shall not be treated as municipal waste. Instead it shall be left at the appropriate collection point for recycling. •...
Page 16
QUESTIONS, PROBLEMS, OR MISSING PARTS? Please Contact Customer Service Before Returning to Store www.soupro.com cs@soupro.com +1-800-239-0689 Crafted in China Ver. 4 Distributed by Source Pro USA Inc., 26300 SC HWY 121, Whitmire, SC 29178 USA...