Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for London Fog Colt-4
- Page 1 Jan., 2018 rev. COLT-4 ULV Handheld Aerosol Generator - With 4 Cycle Gasoline Engine OPERATING INSTRUCTIONS ILLUSTRATED PARTS CUSTOMER SERVICE – A TRADITION 505 Brimhall Ave PO Box 406 Long Lake, Minnesota 55356 PHONE: (952) 473-5366 www.londonfoggers.com salessupport@londonfoggers.com...
- Page 2 The obligation under this warranty is expressly limited to the replacement or repair, at the Company’s option, at the plant of LONDON FOG, INC., Long Lake Minnesota or at a service facility designated by the company, of such part or parts as inspection shall disclose to have been defective.
- Page 3 Specifications Colt-4: Engine: Air Cooled, 4 stroke single cylinder, regular gasoline only Fuel Tank: 20 Ounces, (.65 liters) 35-45 minute run time Compressor: Rotary Vane, Oil-less, 100% ball and roller bearing, graphite air fins Formulation Tank: One Quart, 32 ounces (.946 liters)
-
Page 4: Pre-Start Checklist
PRE-START CHECKLIST All safety equipment is in place _____ Sufficient gasoline in gas tank _____ Oil in engine at proper level _____ All fluid lines tight and connected _____ Sufficient formulation in tank _____ Flow rate is calibrated _____ Nozzle is aimed properly _____ Spray switch is in OFF position _____... - Page 5 COLT-4 Quick Start Checklist A. Engine 1) Please check oil level in Colt-4 Honda engine with indicator in dipstick before each use 2) Engine is a 4 cycle engine, and thus uses only STRAIGHT GASOLINE, please do NOT mix any oil with the gasoline.
-
Page 6: Safety Precautions
IN NO WAY IS IT TO BE CONSTRUED THAT THE CHEMICALS AND/OR DOSAGES ARE THE RECOMMENDATION OF LONDON FOG, INC. LONDON FOG, INC. SHALL IN NO EVENT BE LIABLE FOR CONSEQUENTIAL DAMAGES OR CONTINGENT LIABILITIES ARISING OUT OF THE FAILURE... -
Page 7: Engine Oil Level
OPERATING INSTRUCTIONS (continued) SERVICE BEFORE START-UP Engine Prestart Preparations ENGINE OIL LEVEL BEFORE EACH USE check the oil as follows: Make sure the engine is stopped and resting on a level surface. Also make sure the engine is cool and the oil has had time to drain into the sump. -
Page 8: Operation
OPERATING INSTRUCTIONS (continued) NEVER FILL FUEL TANK INDOORS, WITH ENGINE RUNNING OR WHILE ENGINE IS HOT. NEVER FILL FUEL TANK COMPLETELY. FILL TANK TO WITHIN 1/4 TO 1/2 INCH OF TOP OF TANK TO PROVIDE SPACE FOR FUEL EXPANSION. WIPE ANY FUEL SPILLAGE FORM ENGINE AND EQUIPMENT BEFORE STARTING ENGINE. - Page 9 OPERATING INSTRUCTIONS (continued) AEROSOL OPERATING INSTRUCTIONS Use only insecticide formulation labeled for ground ULV application and supplied by a reputable dealer or distributor. In order to obtain the best aerosol quality, allow engine and compressor to run until the engine is warmed up before turning the aerosol ON.
- Page 10 OPERATING INSTRUCTIONS (continued) INDOOR APPLICATION It is a good practice to remove all pets and animals when possible. Fish bowls and aquariums should be removed or covered. The air supply to aquariums should be turned off. Shut off the area to be treated as tightly as possible. Close all doors and windows.
- Page 11 OPERATING INSTRUCTIONS (continued) (cu.ft. of area to be treated) (oz. of formulation req'd per 1000 cu.ft.)= oz. of formulation 1000 oz. of formulation = application time in minutes calibrated flow rate in oz./min. Example: A 50,000 cu. ft. area is to be treated using 1/4 oz. of formulation per 1000 cu.
-
Page 12: Outdoor Applications
OPERATING INSTRUCTIONS (continued) OUTDOOR APPLICATIONS Areas around homes, picnic areas, swimming pools, etc. Best results are obtained in the cooler hours of early morning or evening when the insects are most active. Ideal wind speed is between 3-7 mph. If wind speed exceeds 10 mph., it is not recommended to disperse insecticide. -
Page 13: Preparation For Storage
OPERATING INSTRUCTIONS (continued) PREPARATION FOR STORAGE MACHINE Prepare unit for storage by draining all the formulation from the container. Then partially fill container with range oil (#1 fuel oil), kerosene or de-odorized kerosene, or mineral oil. Flush system by operating unit until the above base oil is consumed. Finally drain any remaining base oil from the container. - Page 14 Colt PN # 4-1000 Balloon Number Part Number 1 Blower Complete w filter w pulley w nozzle 4-200 2 Blower Filter Assy 4-208 3 Blower Pully 4-274 4 Blower Nozzle 4-303 5 Blower Nozzle tip 4-302 6 Formulation Tank complete with cap and 1/4 in. OD hose 4-700 7 Spray On Off assy Complete 4-650...
- Page 15 ORIFICE DISC CHART (see item #8 on Exploded View, Prev Page for orifice location) NOTE: To order replacement orifices or orifices not listed, use part number # 4- 663 for kit of 3 replacement discs. *Chemical formulations with “thin” viscosity carrier oils such as kerosene, mineral oil, diluent oils, Etc.