Do you have a question about the IPEX2001 and is the answer not in the manual?
Questions and answers
Summary of Contents for IPLINX IPEX2001
Page 1
IPEX2000 Series Installation Guide Rev 160714 11675 Ridgeline Dr. Toll-Free: 800-530-8998 Colorado Springs, CO 80921 Fax: 719-260-0075 supportlibav@libav.com...
IPEX2000 Series Installation Guide Important Safety Instructions 1. Read these instructions – All the safety and operating instructions should be read before this product is operated. 2. Keep these instructions – The safety and operating instructions should be retained for future reference. 3.
Page 4
IPEX2000 Series Installation Guide 26. When the apparatus is not in use or during its relocation, take care of the power cord and plugs; e.g. tie up the power cord with cable tie or similar. The tie must be free from sharp edges and the like that might cause abrasion of the power cord.
60 Hz. The IPEX2001 outputs two video streams: one large IP stream at the native content resolution and a smaller video stream at 352x288 at 5 Hz to easily view a preview of the content on the IPLinx Control software for Windows and iPad.
IPEX2000 Series Installation Guide Front and Rear Panels IPEX2001 Front Panel Power indicator Status indicator IPEX2001 Rear Panel 12V DC power input RS232 Connection HDMI input Analog audio output LAN connection with PoE support Ground screw...
IPEX2000 Series Installation Guide IPEX2002 Front Panel Power indicator Status indicator IPEX2002 Rear Panel 12V DC power input HDMI input Local HDMI output Analog audio output RS232 connection Ground screw...
CBR is Constant Bit Rate. In a CBR h.264 stream, the encoder uses the same amount of bits for every second of video. If you set the IPEX2001 to CBR at 10 megabits per second, every second of video will use 10 megabits per second of bandwidth regardless of the content.
The IPEX2002 can turn on and turn off connected displays via CEC. This technology has been a part of the HDMI specification for years. The IPLinx Control software for Windows and iPad can turn on and off the displays for easy end user control.
Display Audio Output Connections To use the analog audio outputs of the IPEX2001 or IPEX2002, connect the L, R, and ground wires to the removable 3-pole terminal block. Connect the other end of the cable to an audio amplifier. IPEX2001 or...
The video configurations and signal routes can be easily changed through the IPLinx Control software for Windows and iPad or through a third party controller. Please see the IPEXCB user manual for configuring this functionality.
In addition to matrix configurations, multiple IPEX2002 devices can be configured to make a video wall up to 16x16 in size. This functionality is also managed through the IPLinx Control software for Windows and iPad or through a third party controller.
Updates and Troubleshooting Firmware Updates Firmware updates for the IPEX2001 and IPEX2002 are handled through the IPLinx Updater software, which can be found on the IPEXCB page of the Liberty website. Please see the documentation included with the software to update the encoders and decoders.
IPEX2000 Series Installation Guide IPEX2001 Technical Specifications Input/Output Connections HDMI Input One (1) HDMI Type A Receptacle One (1) 8P8C port (Shielded RJ45) Power One (1) 5.5 mm OD, 2.6 mm ID Threaded Barrel RS232 Port One (1) 3-pin Removable Terminal Block Connector...
Installation Guide, Power Supply with US, UK, EU, and UK adapters, 3-pin Removable Screw Terminal (2 ea), Mounting Ears (2 ea) IP Controller IPEXCB Compatible Encoder IPEX2001 Distances and picture quality may be affected by cable grade, cable quality, source and destination equipment, RF and electrical interference, and cable patches.
Need help?
Do you have a question about the IPEX2001 and is the answer not in the manual?
Questions and answers