Advertisement
SPECIFICATIONS
Speeds:
25 ~ 75MPM
Motor:
50HZ 2HP 1430RPM 3PHASE
Capacity: 90
10
90
250mm
1
45
8
/
2
45
215mm
10
15
9
250 385mm
200 400mm
1
10
8
/
2
250 215mm
Blade:
1
0.032
Dimension:
16
250S
250SSA L74
Blade Wheels: 14 (355mm) Diameter
Shipping Weight: 250S
130 (27mm 0.9mm 3300mm)
L71
W30 (L:1800mm W:760mm)
W30 (L:1880mm W:760mm)
430kgs/500kgs
250SSA
450kgs/520kgs
3/2002
Advertisement
Table of Contents
Related Manuals for Unimac UE-250S
Summary of Contents for Unimac UE-250S
-
Page 1: Specifications
SPECIFICATIONS Speeds: 25 ~ 75MPM Blade: 0.032 130 (27mm 0.9mm 3300mm) Motor: 50HZ 2HP 1430RPM 3PHASE Dimension: Capacity: 90 250S W30 (L:1800mm W:760mm) 250mm 250 385mm 200 400mm 250SSA L74 W30 (L:1880mm W:760mm) Blade Wheels: 14 (355mm) Diameter 215mm 250 215mm Shipping Weight: 250S 430kgs/500kgs 250SSA... - Page 2 WARNING 〝 〞...
- Page 3 Environment Requirements for Installation. Noise Level Handling & Transportation of Machine Transportation Methods WARNING...
- Page 4 ELECTRICAL CONNECTION/DISCONNECTION. FOR 3 PHASE 1. Electrical connection: 2. Electrical disconnection: 3. Grounding. WARNING ! FOR SINGLE PHASE...
- Page 7 R.S. . U1.V1. . U2.V2. . U3.V3. .0.1.2.3.4.5.6.7.8.9.10.11.12.13.14. R.S.T. .U1.V1.W1. .U2.V2.W2. .U3.V3.W3. .0.1.2.3.4.5.6.7.8.9.10.11.12.13.14.
-
Page 9: Electrical Connections
Electrical Connections ! WARNING ! WARNING Main Motor Coolant Pump Fig. 1 Control Transformer – Note: Controls – Figure 2 & 3 Power indicator Light Start Button Fig. 2 Emergency Stop Button 〝 〞 Coolant Switch 〝 〞 Cutting Pressure Control Hydraulic On-Off Valve Arm Lift Up Button Arm Descent Button... -
Page 10: Prior To Operation
Prior to Operation Adjust the Variable Speed 〞 〞 Fig. 4 〝 〞 Automatic Shut-Off Adjustment The motor should shut off immediately after the blade has cut through the material and just before the head comes to rest on the horizontal stop bolt. If the machine continues to run after the workpiece has been fully cut, locate and adjust Adjusting Vise Square to the Blade the micro switch mounting plate down. -
Page 11: Changing Blades
Changing Blades ! WARNING 〞 Fig. 5 Caution: Fig. 6 Fig. 7... - Page 12 Blade Tracking Adjustment ! WARNING Fig. 8 Thrust Roller Adjustment Fig. 9 Connect machine to power source.
- Page 13 Guide Roller Adjustment Fig. 10 Connect machine to the power source. Bow Weight Adjustment Fig. 11...
-
Page 14: Angle Adjustment
Angle Adjustment To swivel the saw arm up to a 45 angle: Fig. 12 To adjust the 90 stop: Fig. 13 To adjust the 45 stop: Fig. 14... -
Page 15: Vise Adjustment
Vise Adjustment To position the moveable vise jaw: To adjust the vise for angle cutting: Fig. 15 Maintenance Lubrication Fig. 16 To change gear box lubricant: Fig. 17... - Page 16 Hydraulic System Fig. 18 To refill oil Adjust Saw Arm Starting Position Set Fig. 19...
-
Page 17: Part List
PART LIST Part Part Description Size No. Q’ty Description Size No. Q’ty... - Page 18 PART LIST Part Part Description Size No. Q’ty Description Size No. Q’ty 〞 〞 〞 〞 〞...
- Page 19 PART LIST Part Part Description Size No. Q’ty Description Size No. Q’ty 〞...
- Page 20 113(3) 112 123(2) 103(2) 122(2) 114(3) 51-1 116(2) 52(2) 96(4) 117(2) 94(2) 53(2) 95(2) 99(2) 49(2) 82(2) 100(2) 83(2) 75 45 91-2 91-1 78(2) 77(2) 30(3) 55-1 29(3) 38(2) 38-1(2) 32(4) 22(2) 5(2) 31(2) 23-1 70-1(2) 25(3) 24(3) 26(2) 24-1(2) 2(4) 24-2(6) 3(4)
- Page 21 127(2) 128(2) 123(2) 113(3) 122(2) 114(3) 103(2) 130(4) 116(2) 118(2) 51-1 117(2) 52(2) 96(4) 53(2) 95(2) 99(2) 94(2) 49(2) 82(2) 100(2) 83(2) 47 93 91-1 91-2 78(2) 77(2) 30(3) 55-1 29(3) 38(2) 141(4) 38-1(2) 32(4) 22(2) 5(2) 139-3 31(2) 23-1 139-2 25(3) 139-1...
- Page 22 143(6) 251-1(8) 284(13) 262 263 267(3) 266(3) 260-1 265(3) 189(2) 203(4) 198(4) 201(4) 197(4) 202(4) 273(2) 186-1 272(4) 232(4) 231(4) 230(2) 229(2) 159(12) 228(2) 224(4) 176(4) 223(2) 177(4) 162(3) 173(2) 248(2) 235(6) 160(2) 217(2) 242(8) 216(2) 241(4) 240(4) 166(2) 251(6) 165(2) 164(2) 0 11...
Need help?
Do you have a question about the UE-250S and is the answer not in the manual?
Questions and answers