Summary of Contents for Lifemax FH1517204
- Page 1 MODEL: FH1517204 FINGERHUT ASSEMBLY INSTRUCTIONS Please contact us before returning the product to the store. themdsports.com Register Now on and Earn One-Year Warranty for Free!
- Page 2 LIMITED 90 DAYS WARRANTY This product is covered by a limited warranty that is effective for 90 days from the date of purchase. If, during the limited warranty period, a part is found to be defective or breaks, we will offer replacement part at no cost to you, the customer.
-
Page 3: Tools Required
Power Tools TOOLS REQUIRED: - Set Low Torque Phillips Screwdriver - Not Included Standard (Flat Head Screwdriver) - Not Included Allen Key - Included High Torque over tightened Electric Screwdrivers may be helpful during assembly; however, please set a low torque and use extreme caution. - Page 4 IMPORTANT SAFETY INSTRUCTIONS Read all instructions 1. Read all instructions-All the safety and operating instructions should be read carefully before this hockey game is played. 2. Caution-This is not a toy and is intended for use by or under the supervision of adults. Adults should review safety guidelines with children to avoid possible risk of electric shock or other injuries.
- Page 5 1517204 PARTS LIST Mainframe Left Leg Right Leg Leg Panel Table Tennis Allen Key Leg Ieveler EVA Pad 5/16” x 1-1/4” Bolt 22mm Washer 1/2” Screw Pusher Table Tennis Felt Pad Puck Table Tennis Post Paddle Table Tennis Net Table Tennis Ball 1517204 PRE-INSTALLED PARTS Blower Control Box...
- Page 6 1517204 PRE-INSTALLED PARTS Time Display Battery Box Time Display Wire Scorer Display Wire Puck Catcher Puck Catcher with Long Wire with Short Wire ASSEMBLY INSTRUCTIONS: 1. Find a clean, level place to begin the assembly of your Billiard Table. The table will be assembled upside down and then turned over on its legs once the assembly completed.
- Page 7 FIG. 1 X 12 X 12 X 12 FIG.1 3. Attach the Left Leg (#2) and Right Leg (#3) to the Hockey Mainframe (#1) using three Bolts (#10) and Cerrojo (#11) per Leg. See FIG.1. FIG. 2 1517204 (Continued on the next page.) www.themdsports.com...
- Page 8 FIG.2 4. Attach the Leg Panel (#4) to the Leg using four Screws (#9) per Leg Panel. See FIG. 2 5. Screw the Leg Leveler (#8) into the Leg. See FIG. 2. 6. Lift the table assembly from the floor with at least two strong adults, turn it over, and set the table assembly on its legs in the location where you play.
- Page 9 FIG4A FIG. 4 X 12 FIG.4 7. Tear off the backside paper of the EVA Pads (#7) and stick them at the bottom of the Table Tennis Top (#6). See FIG. 4A. FIG. 5 FIG.5 8. Place the Mainframe and place the Table Tennis Top (#6) on the Hockey surface. And then Insert the Net Posts (#15) and Net (#17) on the Table Tennis Top.
-
Page 10: Motor Schematic Diagram
FIG. 6 FIG.6 9. Tear off the backside paper of the Felt Pad (#13) and stick them at the bottom of the Pushers (#12). Underside the table Scorer Display Puck Catcher Time Display with Long Wire Time Display Wire Battery Box Scorer Display Wire Control Box Scorer Display... - Page 11 ELECTRONIC SCORER OPERATION Install Batteries Battery Box: Unscrew bolt using a screwdriver and open the battery box. Insert 4 “AA” batteries ( not included) in the order of polarity as shown on the inside cover. Then close the cover using a screwdriver. Turn the power ON using the ON/OFF switch.
- Page 12 Inlay Electronic Scorer Trouble Shooting Guides Conditions Trouble Shooting Solvent 1. Pls check the "power switch of Battery Box" if it is turned on. Turn on the power switch of Battery Box. 2. Pls check the "power switch of Control Box" if it is turned on. Turn on the power switch of Control Box.