Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Comelit 20004501
Summary of Contents for Comelit 20004501
- Page 1 COMELIT AUDIO PLAYER ART. 20004500 - 20004501 - 20004502...
-
Page 3: Table Of Contents
FUNCTIONAL PRINCIPLE ......................4 COMELIT AUDIO PLAYER ......................5 SERVER AND PLAYER WITHOUT AMPLIFIER (ART.20004500) ......... 5 PLAYER WITH AMPLIFIER (ART.20004501) ................5 PLAYER WITHOUT AMPLIFIER (ART.20004502) ..............5 SCOPE OF SUPPLY AND INTERFACES ................. 5 INSTALLATION DIAGRAMS ......................6 INSTALLING THE MODULE SERVER AND PLAYER WITHOUT AMPLIFIER (ART.20054000) 7... -
Page 4: Introduction
Congratulations on your purchase of the new Comelit Audio Player and thank you for your confidence in our product. We are certain that you will enjoy every minute with your COMELIT AUDIO PLAYER. To get the best from your new device from the very start, we recommend that you read the operating instructions carefully. -
Page 5: Comelit Audio Player
SCOPE OF SUPPLY AND INTERFACES A power supply unit for the device 20004501 and 20004502 is NOT included! Apart from the connection for the power supply (Art.20004501 - 24 Vdc, Art.20004502 - 12-32 Vdc), the COMELIT AUDIO PLAYER offers the following ports: •... -
Page 6: Installation Diagrams
INSTALLATION DIAGRAMS 1 AUDIO ZONE WITH AMPLIFIER 1 AUDIO ZONE WITHOUT AMPLIFIER 2 AUDIO ZONE WITH AMPLIFIER MODULE... -
Page 7: Installing The Module With Amplifier (Art.20054001)
RJ45 socket for Ethernet LAN 2 x 20 W at 4 Ω - L + | - R + The COMELIT AUDIO PLAYER has two DUO-LEDs, each of which has one green and one red LED. (“Power/Boot” and “Status”) Explanation: The green “Power/Boot”... -
Page 8: Installing The Module Without Amplifier (Art.20054002)
RJ45 socket for Ethernet LAN Audio line-out, 2 V at 10 kΩ - L + | - R + The COMELIT AUDIO PLAYER has two DUO-LEDs, each of which has one green and one red LED. (“Power/Boot” and “Status”) Explanation: The green “Power/Boot”... -
Page 9: Commissioning
In order to set up the connection to the web interface, you should proceed as follows: First, the IP address setting of the PC must be adapted to the COMELIT AUDIO PLAYER. 1) To do this, open the IP address setting of the PC Now click on Start -->... - Page 10 Confirm settings by clicking “OK” and close the window, so that the new IP address is accepted. If the IP address of your PC and of your COMELIT AUDIO PLAYER are in the same subnet, you can continue with the setup.
- Page 11 To change the IP address of the COMELIT AUDIO PLAYER, click on “CONFIGURATION”. This opens the configuration menu where you can select the Network option to make various changes, such as the IP address. Now adapt the IP address to the old subnet of your PC.
-
Page 12: Assign Server
The internal PLAYER is now linked with the required SERVER. Note: If the server that the COMELIT AUDIO PLAYER should access is changed during operation, the Logitech Media Server must be closed and then opened again. As the IP address of the LMS also changes when the server is changed, it would otherwise not be... -
Page 13: Changing The Device Name
CHANGING THE DEVICE NAME There is a possibility of changing the name of the COMELIT AUDIO PLAYER and of the LMS in one process. In other words, it is not necessary to make changes in two different places! To do this, please follow these instructions: 1. -
Page 14: Server-Player Mode: Commissioning The Audio Module With An Internal Server
In this case the COMELIT AUDIO PLAYER functions simultaneously as SERVER and CLIENT (only for 20004501 and 20004502). In other words, the internal client accesses the internal server so that the device can also be used in “stand-alone” mode. In this mode, however, there are restrictions. It is only possible to connect storage media with a total capacity of up to 32 GB, i.e. -
Page 15: Setting Up Playlists
Media Server which is started on the COMELIT AUDIO PLAYER, the COMELIT AUDIO PLAYER is simultaneously a “UPnP-renderer” and “UPnP-server”. In this way, the COMELIT AUDIO PLAYER can easily be controlled by means of a UPnP application, e.g. from a smartphone. -
Page 16: Additional Functions
ADDITIONAL FUNCTIONS This section describes additional functions that are important not only for the COMELIT AUDIO PLAYER, but also for the various functions of the COMELIT AUDIO PLAYER, Client Mode and Server-Client Mode. NETWORK Under the Network menu option various changes can be made, such as the IP address, DNS server or the NTP server. -
Page 17: Firmware Update
FIRMWARE UPDATE As a matter of principle, all COMELIT AUDIO PLAYER firmware from Version 1.0.8 can be updated. The firmware update is free of charge. You will find the latest firmware files on the Comelit Web site www.comelitgroup.com. 1. Under “Configuration” – “System”, select COMELIT AUDIO PLAYER 2.
Need help?
Do you have a question about the 20004501 and is the answer not in the manual?
Questions and answers