1. Manuals
  2. Brands
  3. Flying Voice Manuals
  4. Wireless Router
  5. FWR9601
  6. User manual

Flying Voice FWR9601 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for Flying Voice FWR9601

Summary of Contents for Flying Voice FWR9601

  • Page 2: Table Of Contents

    Contents FWR9600/FWR9601 User Manual Contents About This User Guide..............................1 Contacting FlyingVoice........................1 Purpose..............................2 Cross references..........................2 Feedback............................. 2 Declaration of Conformity........................... 3 Part 15 FCC Rules..........................3 Warnings and Notes............................ 4 Warnings..............................4 Notes..............................4 Chapter 1: Product description..........................5 FWR9202/FWR9601............................ 6 LED Indicators and Interfaces........................7 Hardware Installation........................10...
  • Page 3 Contents FWR9600/FWR9601 User Manual Network and Security..........................34 WAN..............................34 LAN..............................39 VPN..............................40 Port Forward............................. 41 DMZ..............................42 Port Setting............................43 Routing.............................. 43 Advance............................. 44 Wireless 2.4GHz............................45 Wireless Security..........................48 WMM..............................51 WDS..............................51 WPS..............................52 Station Info............................53 Advanced............................54 Wireless 5GHz............................56 Wireless Security..........................58 WMM..............................59...
  • Page 4 Contents FWR9600/FWR9601 User Manual Firmware Upgrade..........................90 Provision............................90 SNMP..............................92 TR-069..............................93 Diagnosis............................94 Operating Mode..........................96 System Log............................96 Logout..............................96 Reboot............................... 97 Chapter 4:IPv6 address configuration........................98 Introduction............................99 IPv6 Advance........................... 100 Configuring IPv6..........................100 Viewing WAN port status........................102 IPv6 DHCP configuration for LAN/WLAN clients................102 LAN DHCPv6............................
  • Page 5 Table FWR9600/FWR9601 User Manual Table Table 1 Features at-a-glance........................... 6 Table 2 LED Indicators............................. 7 Table 3 Interfaces..............................9 Table 4 IVR Menu Setting Options......................... 12 Table 5 Web management interface........................20 Table 6 Setting time zone............................21 Table 7 Configuring an internet connection......................22 Table 8 Wireless >...
  • Page 6 Table FWR9600/FWR9601 User Manual Table 31 Wireless Access Policy..........................50 Table 32 WMM............................... 51 Table 33 WDS................................51 Table 34 WPS................................52 Table 35 Station info...............................53 Table 36 Advanced..............................54 Table 37 Basic................................. 56 Table 38 Wireless security............................58 Table 39 SIP Settings............................... 60 Table 40 VoIP QoS..............................
  • Page 7 Table FWR9600/FWR9601 User Manual Table 65 Daylight Saving Time..........................88 Table 66 System log Setting............................ 88 Table 67 Factory Defaults Setting........................... 89 Table 68 Factory Defaults............................89 Table 69 Firmware upgrade........................... 90 Table 70 Provision..............................91 Table 71 Firmware Upgrade...........................92 Table 72 SNMP................................92 ............................93...
  • Page 8 VoIP.FWR9202/FWR9601 includes extended functions which support, USB memory card,This design not only provide users with a conventional VoIP and routing capabilities. Users can also take FWR9202/FWR9601 as a FTP server, to share LAN files, pictures and other resources. Meanwhile, FWR9202/FWR9601 VoIP wireless router is ideally suited for small and medium enterprises (SMB) to build wireless office.

  • Page 9: About This User Guide

    About This User Manual Contacting FlyingVoice Main website: http://www.flyingvoice.com/ Sales enquiries: sales1@flyingvoice.com Support enquiries: support@flyingvoice.com Hotline: 010-67886296 0755-26099365 Address: Room508-509, Bldg#1, Dianshi Business Park, No.49 BadachuRd,Shijingshan District, Beijing, China...

  • Page 10: Purpose

    About This User Manual Purpose The documents are intended to instruct and assist personnel in the operation, installation and maintenance of the FlyingVoice equipment and ancillary devices. It is recommended that all personnel engaged in such activities be properly trained.FlyingVoice disclaims all liability whatsoever, implied or express, for any risk of damage, loss or reduction in system performance arising directly or indirectly out of the failure of the customer, or anyone acting on the customer's behalf, to abide by the instructions, system parameters, or recommendations made in this document.

  • Page 11: Declaration Of Conformity

    About This User Manual Declaration of Conformity Part 15 FCC Rules This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  This device may not cause harmful interference, and  This device must accept any interference received, including interference that may cause undesired operation.

  • Page 12: Warnings And Notes

    About This User Manual Warnings and Notes The following describes how warnings and notes are used in this document and in all documents of the FlyingVoice document set. Warnings Warnings precede instructions that contain potentially hazardous situations. Warnings are used to alert the reader to possible hazards that could cause loss of life or physical injury.

  • Page 13: Chapter 1: Product Description

    Chapter 1 Product description Chapter 1: Product description This chapter covers: · FWR9202/FWR9601 · LED Indicators and Interfaces · Hardware Installation · Voice Prompt...

  • Page 14: Fwr9202/Fwr9601

    Chapter 1 Product description FWR9202/FWR9601 Table 1 Features at-a-glance Port/Model FWR9202 FWR9601 picture Ethernet 5* RJ45 5* RJ45 interface 10/100M 10/100/1000M T.30, T.38 Fax WiFi 2.4G 2T2R (300Mbps) 2.4G 2T2R(300Mbps) 5G 2T2R (867Mbps) 5G 2T2R (867Mbps) Voice Code G.711 (A-law, U-law), G.729A/B, G.723, G.722 (Wide band)

  • Page 15: Led Indicators And Interfaces

    Chapter 1 Product description LED Indicators and Interfaces Table 2 LED Indicators Status Explanation On (Green) The router is powered on and running normally. POWER The router is powered off. On (Green) The port is connected with 100Mbps. The port is disconnected. Blinking (Green) It will blink while transmitting data.
  • Page 16 Chapter 1 Product description FWR9202 Status Explanation Blinking (Green) Not registered PHONE1/2 On (Green) Registered On (Green) The port is connected with 1000Mbps. LAN1/2/3/4 The port is disconnected. Blinking (Green) It will blink while transmitting data. On (Green) The port is connected with 1000Mbps. The port is disconnected.

  • Page 17: Table 3 Interfaces

    Chapter 1 Product description Table 3 Interfaces FWR9601 Interface Description Phone1 ATA Analog phone connector POWER Connector for a power adapter RESET Restore the factory settings button, press and hold the device after 5s to restore Wi-Fi security settings, when mobile phones, laptops and other wireless devices to...

  • Page 18: Hardware Installation

    Chapter 1 Product description Hardware Installation Before configuring your router, please see the procedure below for instructions on connecting the device in your network. Procedure 1 Configuring the Router Connect analog phone to ATA Port with an RJ11 cable. Connect the WAN port to the Interne your network’s modem/switch/router/ADSL equipment using an Ethernet cable.
  • Page 19 Chapter 1 Product description Warning Changes or modifications not expressly approved by the party responsible for compliance can void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

  • Page 20: Ivr Voice Prompt

    Chapter 1 Product description IVR Voice Prompt The devices may be configured by navigating the unit’s voice menu. By using your phone and dialing a sequence of commands, the device can be configured for operation. Each device configuration section may be accessed by entering a certain operation code, as shown below. Table 4 IVR Menu Setting Options Operation Menu Navigation...
  • Page 21 Chapter 1 Product description Pick up phone and press “****” to start IVR Choose “2”, and The router reports current WAN Port IP Address Input the new WAN port IP address and press “#” key: Use “*” to replace “.”, for exampleuser can input 192*168*20*168 to set the new IP address 192.168.20.168 WAN Port IP Press # key to indicate that you have finished...
  • Page 22 Chapter 1 Product description Pick up phone and press “****” to start IVR Choose “5”, and the router reports current DNS Input the new DNS and press # key: Use “*” to replace “.”, user can input 192*168*20*1 to set the new gateway 192.168.20.1.
  • Page 23 Chapter 1 Product description Pick up phone and press “****” to start IVR Choose “6”, and the router reports “ WEB Access Port” Prompt “Please enter password”, the method of inputting password is same as WEB Access operation 1. Port Report “operation successful”...
  • Page 24 Chapter 1 Product description Note .While using Voice menu, press * (star) to return to main menu. 2.If any changes made in the IP assignment mode, the router must be rebooted in order for the settings to take effect. 3.While entering an IP address or subnet mask, use "*" (star) to enter "." (Dot) and use "#"...

  • Page 25: Chapter 2 Basic Settings

    Chapter 2 Basic Settings This chapter covers:  Two-Level Management Web Management Interface   Configuring  Making a Call...

  • Page 26: Two-Level Management

    This section explains how to setup a password for an administrator or user and how to adjust basic and advanced settings. FWR9202/FWR9601 supports two-level management: administrator mode operation: please type “admin/admin” on Username/Password and click Login button to begin configuration.
  • Page 27 Chapter 2 Basic Settings Note If you are unable to access the web configuration, please see Chapter 5: Troubleshooting Guide for more information. 6.The web management interface automatically logs out the user after 5 minutes of inactivity. Login in from the WAN port 1.Ensure your PC is connected to the router’s WAN port correctly.

  • Page 28: Web Management Interface Details

    Chapter 2 Basic Settings Web Management Interface Details Satus Table 5 Web management interface Serial number Name Description Click this navigation bar to bring up the corresponding Postition 1 Main navigation bar child navigation bar Click the sub navigation bar to enter the configuration Postition 2 navigation bar page...

  • Page 29: Setting The Time Zone

    Chapter 2 Basic Settings Setting the Time Zone Table 6 Setting time zone Field Name Description NTP Enable Enable NTP (Network Time Protocol) to automatically retrieve time and date settings for the device Option 42 Whether to enable Option 42 Current Time When NTP Enable is set to “Disable”, manually configure the time and date via the Current Time parameter...

  • Page 30: Configuring An Internet Connection

    Chapter 2 Basic Settings Configuring an Internet Connection From the Network > WAN page, WAN connections may be inserted or deleted. For more information on Internet Connection setting, see Table 10below. Table 7 Configuring an internet connection...
  • Page 31 Chapter 2 Basic Settings Field Name Description Connect Name Use keywords to indicate WAN port service model (the parameters are defined in Network--> multi-WAN page) Service Chose the service mode for the created connection IP Protocol Version IPv4 and IPv6 are supported WAN IP Mode Choose Internet connection mode, DHCP, PPPoE, or Bridge NAT Enable...

  • Page 32: Setting Up Wireless Connections

    Chapter 2 Basic Settings Setting up Wireless Connections To set up the wireless connection, please perform the following steps. 1.Enable Wireless and Setting SSID 2.Open Wireless > Basic webpage as shown below: Table 8 Wireless > Basic web page (user view) Field Name Description Select “Radio Off”to disable wireless operation...

  • Page 33: Encryption

    Chapter 2 Basic Settings Enabled: Devices connected to the router via one of the Multiple SSIDs are isolated from one another on virtual networks MBSSID AP Isolation Disabled: Devices connected to the router via one of the Multiple SSIDs are visible on the network to each other BSSID Basic Service Set Identifier –...

  • Page 34: Configuring Session Initiation Protocol

    Configuring Session Initiation Protocol SIP Accounts FWR9600/FWR9601 have 1 Line to make SIP (Session Initiation Protocol) calls. Before registering, the device user should have a SIP account configured by the system administrator or provider. See the section below for more information.

  • Page 35: Table 10 Configuring Sip The Web Management Interface

    Chapter 2 Basic Settings Configuring SIP the Web Management Interface Table 10 Configuring SIP the Web Management Interface Procedure 1. Open the Line1/SIP Account webpage, as illustrated above. 2. Fill the SIP Server address and SIP Server port number (from administrator or provider) into Proxy Server Name and into Proxy Port parameters.

  • Page 36: Viewing The Registration Status

    Chapter 2 Basic Settings Viewing the Registration Status Table 11 Registration status Procedure To view the SIP account status of device, open the Status webpage and view the value of registration status.

  • Page 37: Making A Call

    Chapter 2 Basic Settings Making a Call Calling phone or extension numbers To make a phone or extension number call:  Both ATA and the other VoIP device (i.e., another ATA or other SIP products) must have public IP addresses, or ...
  • Page 38 Chapter 2 Basic Settings Attended Transfer Assume that call party A and B are in a conversation. A wants to Attend Transfer B to C: Party A dials “*77” to hold the party B, when hear the dial tone, A dials C’s number, then party A and party C are in conversation.

  • Page 39: Chapter 3: Web Interface

    Chapter 3 Web Interface Chapter 3: Web Interface This chapter guides users to execute advanced (full) configuration through admin mode operation. This chapter covers:  Login  Status  Network and Security  Wireless   FXS1  Security  Application ...

  • Page 40: Login

    Chapter 3 Web Interface Login Table 12 Login details Procedure 1. Connect the LAN port of the router to your PC an Ethernet cable 2. Open a web browser on your PC and type http://192.168.1.1. 3. Enter Username admin and Password admin. 4.

  • Page 41: Status

    Chapter 3 Web Interface Status This webpage shows the status information about the Product, Network, SIP Account Status, FXS Port Status, Network Status,Wireless Info and System Status Table 13 Status...

  • Page 42: Network And Security

    Chapter 3 Web Interface Network and Security You can configure the WAN port, LAN port, DDNS, Multi WAN, DMZ, MAC Clone, Port Forward and other parameters in this section of the web management interface. This page allows you to set WAN configuration with different modes. Use the Connection Type drop down list to choose one WAN mode and then the corresponding page will be displayed.

  • Page 43: Table 15 Dhcp

    Chapter 3 Web Interface DHCP The Router has a built-in DHCP server that assigns private IP address to each local client. The DHCP feature allows to the router to obtain an IP address automatically from a DHCP server. In this case, it is not necessary to assign an IP address to the client manually.

  • Page 44: Table 16 Pppoe

    Chapter 3 Web Interface PPPoE PPPoE stands for Point-to-Point Protocol over Ethernet. It relies on two widely accepted standards: PPP and Ethernet. It connects users through an Ethernet to the Internet with a common broadband medium, such as a single DSL line, wireless device or cable modem. All the users over the Ethernet can share a common connection.

  • Page 45: Table 17 Bridge Mode

    Chapter 3 Web Interface Confirm Password Enter your PPPoE password again Service Name Enter a service name for PPPoE authentication. If it is left emply, the service name is auto detected. Operation Mode Select the mode of operation, options are Keep Alive, On Demand and Manual: When the mode is Keep Alive, the user sets the 'keep alive redial period' values range from 0 to 3600s, the default setting is 5 minutes;...
  • Page 46 Chapter 3 Web Interface Field Name Descripti Bridge Type IP Bridge Allow all Ethernet packets to pass. PC can connect to upper network directly. PPPoE Bridge Only Allow PPPoE packets pass. PC needs PPPoE dial-up software. Packets pass through hardware switch with wired speed. Does not support Hardware IP Bridge wireless port binding DHCP Service Type...

  • Page 47: Lan

    Chapter 3 Web Interface LAN Port NAT translates the packets from public IP address to local IP address to forward packets to the proper destination. Table 18 LAN port Field Name Description IP Address Enter the IP address of the router on the local area network. All the IP addresses of the computers which are in the router’s LAN must be in the same network segment with this address, and the default gateway of the computers must be this IP address.

  • Page 48: Vpn

    Chapter 3 Web Interface DHCP Start Address Enter a valid IP address as a starting IP address of the DHCP server, and if the router’s LAN IP address is 192.168.11.1, starting IP address can be 192.168.11.2 or greater, but should be less than the ending IP address. DHCP End Address Enter a valid IP address as an end IP address of the DHCP server.

  • Page 49: Port Forward

    Chapter 3 Web Interface Field Name Description VPN Enable Enable/Disable VPN. If the VPN is enabled, user can select PPTP and L2TP mode VPN. Initial Service IP Enter VPN server IP address. User Name Enter authentication username. Password Enter authentication password. Port Forward Table 20 Port Forward Field Name...

  • Page 50: Dmz

    Chapter 3 Web Interface Table 21 Virtual Servers Field Name Description Comment To set up a virtual server notes IP Address Virtual server IP address Public Port Public port of virtual server Private Port Private port of virtual servers ports Protocol You can select from TCP, UDP, and TCP&UDP.

  • Page 51: Port Setting

    Chapter 3 Web Interface Port Setting ort setting Table 23 P Field Name Description WAN Port speed Nego Auto-negotiation, options are Auto, 100M full, 100M half-duplex, 10M half and full. LAN1~LAN3 Port Speed Auto-negotiation, options are Auto, 100M full, 100M half, 10M half and Nego 10M full.

  • Page 52: Advance

    Chapter 3 Web Interface Field Name Description Destination Destination address Host/Net Both Host and Net selection Gateway Gateway IP address Interface LAN/WAN/Custom three options, and add the corresponding address Comment Comment Advance Table 25 Advance Field Name Description Most Nat connections The largest value which the FWR8401 can provide Mss Mode Choose Mss Mode from Manual and Auto...

  • Page 53: Wireless 2.4Ghz

    Chapter 3 Web Interface Wireless 2.4GHz Basic Table 26 Basic Field Name Description Radio on/off Select “Radio off” to disable wireless. Select “Radio on” to enable wireless. Wireless connection mode According to the wireless client type, select one of these modes. Default is AP Network Mode Choose one network mode from the drop down list.
  • Page 54 Chapter 3 Web Interface SSID It is the basic identity of wireless LAN. SSID can be any alphanumeric or a combination of special characters. It will appear in the wireless network access list. Multiple SSID1~SSID3 The device supports 4 SSIDs. Hidden After the item is checked, the SSID is no longer displayed in the search for the Wi-Fi wireless network connection list...
  • Page 55 Chapter 3 Web Interface Enabled: Multiple copies of signals are transmitted to increase the chance of successful delivery Enabled: Allows the device to aggregate multiple Ethernet frames into a single 802.11n, thereby improving the ratio of frame data to frame overhead Aggregation MSDU (A- MSDU) Disabled: No frame aggregation is employed at the router...

  • Page 56: Wireless Security

    Chapter 3 Web Interface Wireless Security Table 27 Wireless security Field Name Description SSID Choice Choose one SSID from SSID, Multiple SSID1, Multiple SSID2 and Multiple SSID3. Select an appropriate encryption mode to improve the security and privacy of your wireless data packets.Each encryption mode will bring out different web page and ask Security Mode you to offer additional configuration.

  • Page 57: Table 29 Wpa-Psk

    Chapter 3 Web Interface Field Name Description Security Mode This is used to select one of the 4 WEP keys, key settings on the clients should be the same with this when connecting. WEP Keys Set the WEP key. A-64 key need 10 Hex characters or 5 ASCII characters; choose A- 128 key need 26 Hex characters or 13 ASCII characters.

  • Page 58: Table 30 Wpapskwpa2Psk

    Chapter 3 Web Interface WPAPSKWPA2PSK manner is consistent with WPA2PSK settings: Table 30 WPAPSKWPA2PSK Field Name Description The home gateway is used to select the wireless security encryption WPA Algorithms algorithm options are TKIP, AES, TKIP / AES. 11N mode does not support TKIP algorithms.

  • Page 59: Wmm

    Chapter 3 Web Interface Policy Disable : Prohibition: wireless access control policy. Allow: only allow the clients in the list to access. Rejected: block the clients in the list to access. Add a station MAC Enter the MAC address of the clients which you want to allow or prohibit Example: Prohibit the device whose wireless network card MAC address is 00:1F: D0: 62: BA:FF’s to access the wireless network, and allow other computers to access the network.Implementation: As shown, the Policy is Reject, add 00:1F: D0: 62: BA: FF to the MAC, click Save and reboot the device settings to take...

  • Page 60: Wps

    Chapter 3 Web Interface Description WDS stands for Wireless Distribution System, enabling WDS access points to be interconnected to expand a wireless network. WPS (Wi-Fi Protected Setup) provides easy procedure to make network connection between wireless station and wireless access point with the encryption of WPA and WPA2. It is the simplest way to build connection between wireless network clients and wireless access point.

  • Page 61: Station Info

    Chapter 3 Web Interface WPS Current Status Display the current status of WPS Display the configure the status information of WPS WPS Configured Display WPS SSID WPS SSID WPS Progress WPS Mode PIN：Enter the PIN code of the wireless device which accesses to this LAN in the following option, and press apply.

  • Page 62: Advanced

    Chapter 3 Web Interface Advanced Table 36 Advanced Field Name Description BG Protection Mode Select G protection mode, options are on, off and automatic. Beacon Interval The interval of sending a wireless beacon frame, within this range, it will send a beacon frame for the information of the surrounding radio network.
  • Page 63 Chapter 3 Web Interface Pkt_Aggregate It is a mechanism that is used to enhance the LAN, in order to ensure that the home gateway packets are sent to the destination correctly. Support Channel Choose appropriate channel Wi-Fi Multimedia (WMM) WMM Capable Enable/Disable WMM.

  • Page 64: Wireless 5Ghz

    Chapter 3 Web Interface Wireless 5GHz Basic Table 37 Basic Field Name Description Select “Radio off” to disable wireless. Radio on/off Select “Radio on” to enable wireless. Wireless connection According to the wireless client type, select one of these modes. Default is AP mode Choose one network mode from the drop down list.
  • Page 65 Chapter 3 Web Interface Multiple SSID It is the basic identity of wireless LAN. SSID can be any alphanumeric or a combination of special characters. It will appear in the wireless network access list. Multiple SSID1~SSID3 The device supports 4 SSIDs. Broadcast(SSID) After initial State opening, the device broadcasts the SSID of the router to wireless network...

  • Page 66: Wireless Security

    Chapter 3 Web Interface Enabled: Multiple frames are acknowledged together using a single Block Acknowledgement frame. Disabled: Auto block acknowledgement is not used by the device – use this Auto Block Ack configuration when low throughput/connectivity issues are experienced by mobile devices Decline BA Request Enabled: Disallow block acknowledgement requests from devices Disabled:...

  • Page 67: Wmm

    Chapter 3 Web Interface Select an appropriate encryption mode to improve the security and privacy of your wireless data packets.Each encryption mode will bring out different web page and ask Security Mode you to offer additional configuration. Select a different encryption mode, the web interface will be different, user can configure the corresponding parameters under the mode you select.

  • Page 68: Sip

    Chapter 3 Web Interface SIP Settings Table 39 SIP Settings Parameters name Description SIP Parameters SIP T1 The default value is 500 SIP User Agent Name Enter the SIP User Agent header field Max Forward Modify the maximum hop value, the default is 70 Max Auth Change the number of authentication failures, the default value is 2 Reg Retry Intvl...

  • Page 69: Table 40 Voip Qos

    Chapter 3 Web Interface SRTP Prefer Encryption Support for AES_CM and ARIA_CM Service Type Default general DNS Refresh Timer Modify the DNS refresh time, the default value of 0 Transport The transmission type defaults to UDP Response Status Code Handling Retry Reg RSC Fall in Retry Reg RSC NAT Traversal...

  • Page 70: Dial Plan

    Chapter 3 Web Interface Dial Plan Table 41 Dial Plan Field Name Description Dial Plan Enable/Disable dial plan. Line Set the line. Digit Map Enter the sequence used to match input number The syntactic, please refer to the following Dial Plan Syntactic. Action Choose the dial plan mode from Deny and Dial Out.

  • Page 71: Table 42 Adding One Dial Plan

    Chapter 3 Web Interface Adding one Dial Plan Table 42 Adding one dial plan Description Step 1. Enable Dial Plan. Step 2. Click Add button, and the configuration table. Step 3. Fill in the value of parameters. Step 4. Press OK button to end configuration. Dial Plan Syntactic Table 43 Dial Plan Syntactic String...

  • Page 72: Blacklist

    Chapter 3 Web Interface Make outside dial tone after dialing “x”, stop until dialing character “y” For example： “9,1xxxxxxxxxx”:the device reports dial tone after inputting “9”, stops tone until inputting “1” “9,8,010x”: make outside dial tone after inputting “9”, stop tone until inputting “0”...
  • Page 73 Chapter 3 Web Interface Description Click to select the blacklist file and to upload it to device; Click to save the blacklist file to your local computer. Select one contact and click edit to change the information, click delete to delete the contact, click Move to phonebook to move the contact to phonebook.

  • Page 74: Call Log

    Chapter 3 Web Interface Call Log To view the call log information such as redial list , answered call and missed call Table 45 Call log Redial Calls Answered Calls Missed Calls...

  • Page 75: Fxs 1

    Chapter 3 Web Interface FXS 1 SIP Account Basic Set the basic information provided by your VOIP Service Provider, such as Phone Number, Account, password, SIP Proxy and others. Table 46 Line Field Name Description Line Enable Enable/Disable the line. Enable/Disable PEER to PEER.

  • Page 76: Table 47 Audio Configuration

    Chapter 3 Web Interface Proxy port SIP Service port, default is 5060 Outbound Port Outbound Proxy’s Service port, default is 5060 Backup Outbound Port Backup Outbound Proxy’s Service port, default is 5060 Display Name The number will be displayed on LCD Phone Number Enter telephone number provided by SIP Proxy Account...

  • Page 77: Table 48 Supplementary Service

    Chapter 3 Web Interface Auto Gain Control Enable/Disable auto gain T.38 Enable Enable/Disable T.38 T.38 Redundancy Enable/Disable T.38 Redundancy T.38 CNG Detect Enable Enable/Disable T.38 CNG Detect gpmd attribute Enable Enable/Disable gpmd attribute Supplementary Service Subscription Table 48 Supplementary service Field Name Description Call Waiting...

  • Page 78: Table 49 Advanced

    Chapter 3 Web Interface Voice Mailbox Fill in the voice mailbox phone number, Asterisk platform, for example, its default voice Numbers mail is *97 VMWI Serv Enable/Disable VMWI service Enable/Disable DND (do not disturb) If enable, any phone call cannot arrive at the device; default is disable Enter the speed dial phone numbers.
  • Page 79 Chapter 3: Web Interface Parameter name Description Domain Name Type Whether to enable domain name recognition in SIP URIs Carry Port Information Whether to carry the SIP URI port information Signal Port The local port number of the SIP protocol Select the second way of dialing, optional items are In-band, DTMF Type RFC2833 and SIP Info.
  • Page 80 Chapter 3: Web Interface Hold Method Call hold is REINVITE or INFO Request-URI User Check Whether to allow the user to check If enabled, will only accept requests from the server, do not accept Only Recv Request From Server other requests Server Address SIP server address SIP Received Detection...

  • Page 81: Preferences

    Chapter 3: Web Interface Preferences Preferences Table 50 Preferences Field Name Description Handset Input Gain Adjust the handset input gain from 0 to 7. Handset Volume Adjust the output gain from 0 to 7. DTMF Volume (0~-45) Default is -19, you can set a range of values is 0~ -45 Regional Table 51 Regional Field Name...

  • Page 82: Table 52 Features And Call Forward

    Chapter 3: Web Interface Ring Back Tone Ring back tone Call Waiting Tone Call waiting tone Min Jitter Delay The Min value of home gateway’s jitter delay, home gateway is an adaptive jitter mechanism. Max Jitter Delay The Max value of home gateway’s jitter delay, home gateway is an adaptive jitter mechanism.
  • Page 83 Chapter 3: Web Interface Field Name Description Features All Forward Enable/Disable forward all calls Busy Forward Enable/Disable busy forward. No Answer Forward Enable/Disable no answer forward. Call Forward All Forward Set the target phone number for all forward. The device will forward all calls to the phone number immediately when there is an incoming call.

  • Page 84: Table 53 Miscellaneous

    Chapter 3: Web Interface Miscellaneous Table 53 Miscellaneous Field Name Description Codec Loop Current Set off-hook loop current, default is 26 Impedance Maching Set impedance matching, default is US PBX,Korea,Taiwan(600). CID service Enable/Disable displaying caller ID; If enable, caller ID is displayed when there is an incoming call or it won’t be displayed.

  • Page 85: Security

    Chapter 3: Web Interface Security Filtering Setting Table 54 Filtering Setting Field Name Description Filtering If or not enable filter function Default Policy Choose to give up or accept Mac address Add the Mac address filtering Dest IP address Dest IP address Source IP address Source IP address Protocol...

  • Page 86: Content Filtering

    Chapter 3: Web Interface You can choose to receive or give up; this should be consistent with the Action default policy. Add callout Comment Delete Delete selected item Content Filtering Table 55 Content Filtering Field Name Description Filtering Enable/Disable content Filtering Default Policy The default policy is to accept or to prohibit filtering rules Current Webs URL Filters List the URL filtering rules that already existed (blacklist)
  • Page 87 Chapter 3: Web Interface Current Website Host List the keywords that already exist (blacklist) Filters Delete/Cancel You can choose to delete or cancel the existing filter rules the existing keywords Add a Host Filter Add keywords Add/Cancel Click the Add or cancel...

  • Page 88: Application

    Chapter 3: Web Interface Application Advance NAT Table56 advance NAT Description Enable/Disable these function(FTP/SIP/H323/PPTP/L2TP/IPSec). UPnP UPnP (Universal Plug and Play) supports zero-configuration networking, and can automatically discover a variety of networked devices. When UPnP is enabled, the connected device is allowed to access the network, obtain an IP address, and convey performance information.

  • Page 89: Table 58 Igmp

    Chapter 3: Web Interface IGMP Multicast has the ability to send the same data to multiple devices. IP hosts use IGMP (Internet Group Management Protocol) report multicast group memberships to the neighboring routers to transmit data, at the same time, the multicast router use IGMP to discover which hosts belong to the same multicast group.

  • Page 90: Storage(Only For Fwr9202)

    Chapter 3: Web Interface Storage(Only for FWR9202) Disk Management Table 59 Disk Management Field Name Description Adding files to the USB storage device Remove the USB storage device file Delete Transfer files within a USB storage device Remove Disk Format the USB storage device Format Resetting the USB storage device Re-allocate...

  • Page 91: Ftp Setting

    Chapter 3: Web Interface FTP Setting Table 60 FTP Setting Field Name Description FTP Server If or not enable FTP server FTP Server Name Set the FTP server name Anonymous Login If or not support anonymous login FTP Port Set FTP server port number Max.

  • Page 92: Smb Setting

    Chapter 3 Web Interface SMB Setting Table 61 SMB Setting Field Name Description SAMBA Server If or not enable SAMBA server Workgroup Fill in the working group NetBIOS Name Network basic input/output system name Add a shared file Edit Edit a shared file Delete a shared file...

  • Page 93: Administration

    Chapter 3 Web Interface Administration The user can manage the device in these webpages; you can configure the Time/Date, password, web access, system log and associated configuration TR069. Management Save config file Table 62 Save Config File Field Name Description Config file upload and Upload: click on browse, select file in the local, press the upload button to download...

  • Page 94: Table 63 Administrator Settings

    Chapter 3 Web Interface Administrator settings Table 63 Administrator settings Field Name Description User type Choose the user type from admin user and normal user and basic user New User Name You can modify the user name, set up a new user name New Password Input the new password Confirm Password...

  • Page 95: Table 64 Ntp Settings

    Chapter 3 Web Interface NTP settings Table 64 NTP settings Field Name Description NTP Enable Enable/Disable NTP Option 42 Enable/Disable DHCP option 42. This option specifies a list of the NTP servers available to the client by IP address Current Time Display current time NTP Settings Setting the Time Zone...

  • Page 96: Table 65 Daylight Saving Time

    Chapter 3 Web Interface Daylight Saving Time Table 65 Daylight Saving Time Procedure Step 1. Enable Daylight Savings Time. Step 2. Set value of offset for Daylight Savings Time Step 3: Set starting Month/Week/Day/Hour in Start Month/Start Day of Week Last in Month/Start Day of Week/Start Hour of Day, analogously set stopping Month/Week/Day/Hour in Stop Month/Stop Day of Week Last in Month/Stop Day of Week/Stop Hour of Day.

  • Page 97: Table 67 Factory Defaults Setting

    Chapter 3 Web Interface Field Name Description Syslog Enable Enable/Disable syslog function Syslog Level Select the system log, there is INFO and Debug two grades, the Debug INFO can provide more information Remote Syslog Enable Enable/Disable remote syslog function Remote Syslog server Add a remote server IP address Syslog Enable Enable/Disable syslog function...

  • Page 98: Firmware Upgrade

    Chapter 3 Web Interface Firmware Upgrade Table 69 Firmware upgrade Description 1. Choose upgrade file type from Image File and Dial Rule 2. Press “Browse..” button to browser file 3. Press to start upgrading Provision Provisioning allows the router to auto-upgrade and auto-configure devices which support TFTP, HTTP and HTTPs .

  • Page 99: Table 70 Provision

    Chapter 3 Web Interface Table 70 Provision Field Name Description Enable provision or not. Provision Enable Enable resync after restart or not Resync on Reset Resync Random Set the maximum delay for the request of synchronization file. The default is 40 Resync Periodic(sec) If the last resync was failure, The router will retry resync after the “Resync Error Resync Error Retry...

  • Page 100: Snmp

    Chapter 3 Web Interface Table 71 Firmware Upgrade Field Name Description Upgrade Enable Enable firmware upgrade via provision or not Upgrade Error Retry If the last upgrade fails, the router will try upgrading Delay(sec) again after “Upgrade Error Retry Delay” period, default is 3600s Upgrade Rule URL of upgrade file SNMP...

  • Page 101: Tr-069

    Chapter 3 Web Interface TR-069 TR-069 provides the possibility of auto configuration of internet access devices and reduces the cost of management. TR-069 (short for Technical Report 069) is a DSL Forum technical specification entitled CPE WAN Management Protocol (CWMP). It defines an application layer protocol for remote management of end-user devices.

  • Page 102: Diagnosis

    Chapter 3 Web Interface Periodic Inform Enable Enable the function of periodic inform or not. By default it is Enabled Periodic Inform Interval Periodic notification interval with the unit in seconds. The default value is 3600s Connect Request parameters User Name The username used to connect the TR069 server to the DUT.
  • Page 103 Chapter 3 Web Interface Description 1. Packet Trace Users can use the packet trace feature to intercept packets which traverse the device. Click the Start button to start home gateway tracking and keep refreshing the page until the message trace shows to stop, click the Save button to save captured packets.

  • Page 104: Operating Mode

    Chapter 3 Web Interface Operating Mode Table 75 Operating mode Description Choose the Operation Mode as Basic Mode or Advanced Mode System Log Table 76 System log Description If you enable the system log in Status/syslog webpage, you can view the system log in this webpage. Logout Table 77 Logout Description...

  • Page 105: Reboot

    Chapter 3 Web Interface Reboot Press the button to reboot the device.

  • Page 106: Chapter 4:Ipv6 Address Configuration

    Chapter 4: IPv6 address configuration The router devices support IPv6 addressing.This chapter covers:  Introduction  IPv6 Advance  Configuring IPv6 Viewing WAN port status   IPv6 DHCP configuration for LAN/WLAN clients  LAN DHCPv6...

  • Page 107: Introduction

    Chapter 4 IPv6 address configuration Introduction DHCPv6 protocol is used to automatically provision/configure IPv6 capable end points in a local network. In addition to acquiring an IPv6 IP address for the WAN interface and its associated LAN/WLAN clients, the devices are also capable of prefix delegation. The Routers devices support the following types of modes of IPv6 addresses: ...

  • Page 108: Ipv6 Advance

    Chapter 4 IPv6 address configuration IPv6 Advance To enable IPv6 functionality: Navigate to Network > IPv6 Advanced page. Select Enable from the IPv6 Enable drop-down list. Click Save. Table 79 Enabling IPv6 Configuring IPv6 Configuring Statefull IPv6 1. Navigate to Network > IPv6WAN page. The following window is displayed: Table 80 Configuring Statefull IPv6 Field Name Description...

  • Page 109: Table 81 Configuring Stateless Ipv6

    Chapter 4 IPv6 address configuration DHCPv6 Address Settings Set it to statefull mode. Prefix Delegation Select Enable. Configuring Stateless IPv6 Table 81 Configuring Stateless IPv6 Field Name Description Connection Type Select connection type DHCPv6 Address Settings Set it to stateless mode. Prefix Delegation Select Enable.

  • Page 110: Viewing Wan Port Status

    Chapter 4 IPv6 address configuration Viewing WAN port status To view the status of WAN port: Navigate to Status page. IPv6 DHCP configuration for LAN/WLAN clients Wired and wireless clients connected to the Routers can obtain their IPv6 addresses based on how the LAN s ide DHCPv6 parameters are configured.

  • Page 111: Lan Dhcpv6

    Chapter 4 IPv6 address configuration LAN DHCPv6 When IPv6 is enabled, the LAN/WLAN clients of Routers can be configured to receive IPv6 addresses from locally configured IPv6 pool or from an external DHCPv6 server. To enable LAN DHCPv6 service:...

  • Page 112: Chapter 6:Troubleshooting Guide

    Chapter 6: Troubleshooting Guide This chapter covers:  Configuring PC to get IP Address automatically  Cannot connect to the Web GUI  Forgotten Password...

  • Page 113: Configuring Pc To Get Ip Address Automatically

    Chapter 6 Troubleshooting Guide Configuring PC to get IP Address automatically Follow the below process to set your PC to get an IP address automatically: Step 1 : Click the “Start” button Step 2 : Select “control panel”, then double click “network connections” in the “control panel” Step 3 : Right click the “network connection”...

  • Page 114: Cannot Connect To The Web

    Chapter 6 Troubleshooting Guide Cannot connect to the Web Solution:  Check if the Ethernet cable is properly connected  Check if the URL is correct. The format of URL is: http:// the IP address  Check on any other browser apart from Internet explorer such Google ...

This manual is also suitable for:

Fwr9202

Table of Contents