Single channel timeswitch,
dual channel programmer (2 pages)
Summary of Contents for Drayton LP111Si
Page 1
User instructions with the end user Lifestyle SERVICE INTERVAL SINGLE DUAL CHANNEL CHANNEL Timeswitch Programmer for heating hot water for heating hot water LP111Si, LP711Si LP241Si, LP522Si, LP722Si SINGLE DUAL CHANNEL CHANNEL Installation Instructions ISS F 06490050001 Technical Helpline: 0333 7000622 Email: customer.care@draytoncontrols.co.uk Web: www.draytoncontrols.co.uk...
Page 2
PROGRAM MAKE SURE MAINS INPUT HAS A 3 AMP FUSE. MAKE TECHNICAL DATA LP241Si, LP522Si & LP722Si PROGRAMMERS Drayton LP111Si & LP711Si TIMESWITCHES Drayton L Voltage 230V a.c. +10% - 10% 50Hz Switchma 2 (1) A 230V a.c. each switch...
Page 3
2014/30/EC – Electromagnetic compatibility Myson 2014/35/EC – Low voltage Myson Potterton BEFORE INSTALLATION Potterton First, make sure the mains supply is switched off! Salus Sangamo PROGRAMMER ONLY Sunvic The programmer must be set to the type of system it is to con- Sunvic * Can simp trol.
Page 4
- only leave TIMESWITCH TERMINAL COMPARISONS MAKE MODEL Current Models Drayton Tempus 1, 2 (new models) Drayton Lifestyle LP111, LP711, LP111Si, LP711Si Switchmaster Discontinued/Competitors’ Models for heatin TC (Towerchron) ot water Drayton Drayton miGenie Wish 1...
Page 5
Current Models On some Drayton Tempus 3, 4, 6, 7 (old models), Tempus 6, 7 the heati chosen ‘O Drayton Lifestyle LP112, LP241, LP522, LP722 Switchmaster 400, 600 The time (no connection to terminal 4 on 600) have to b...
Page 6
Terminal L or from a separate supply with a 3A fuse. ht of WIRING THE PROGRAMMER Rememb USING A DRAYTON SIMP-L-FIT, ALTHOUGH NOT ge the Make yo NECESSARY, WILL MAKE THIS INSTALLATION EASIER. it into on the p Connection Charts You can’...
Page 7
Switchin On the It allow the pro you ca 1. Press A stay on you do 6 1,2,3 beginn Advanc LP111Si, LP711Si LP241Si, LP522Si, LP722Si 2. Press & be disp To canc SINGLE DUAL already three h CHANNEL CHANNEL Over-rid User’s Instructions...
Page 8
Email: customer.care@draytoncontrols.co.uk Web: www.draytoncontrols.co.uk What is a programmer? ...an explanation for householders Programmers allow you to set ‘On’ and ‘Off’ time periods. Some models switch the central heating and domestic hot water on and off at the same time, while others allow the domestic hot water and heating to come on and go off at different times.
Page 9
The light on the front of the timeswitch shows when it’s on. Press th heating LP111Si – a 24hr program, up to 3 heating periods buttons each day, and every day the same. in 10-m LP711Si –...
Page 10
OFF2, ON3, OFF3. If you get out of sequence, the display will to the flash a warning. If you Codes start ag SWITCHING pre-se ON 1 – start of first timed period The stan OFF 1 – end of first timed period Your sy ON 2 –...
Page 11
TIMED. iods. c hot THE LP111Si 24hr ELECTRONIC TIMESWITCH ff at LP111Si – a 24hr program, up to 3 heating periods each day, Press S and every day the same. period. estyle. Want to leave a timing as it is? Just press SET? and move on...
Page 12
OFF 3 – final switch-off of the day 10.30pm Changing the timings Press the SET? button and you’ll see ‘SET PROG?’. Press YES times in th stem on the Set each d PROG? If, after you Press the YES button, and you’ll see ON1, the start of your first tune Satur heating period.
Page 13
pre-set program. Lifestyle P heating an The standard program Dependin Your system will come on for up to 3 heating periods every can either independe 24hrs. ON1 starts the first one, OFF1 finishes it, and so on. shows wh Notice that ON2 and OFF2 are set to the same time.* This means your system won’t respond, but if you want to activate that middle period or change any other timings –...
Page 14
MON TUE WED THU FRI flash a wa PROG? Press YES and you’ll see ON1, the start of your first heating peri- od. Adjust it in 1-minute steps using the – and + buttons. If the – and + buttons are held down, the time changes in 10-minute steps.
Page 15
2. Press & H times in the same way. be display To cancel Set each day water is a If, after you’ve set OFF3 for both SAT & SUN, you want to fine- ur first two or thr tune Saturday or Sunday, press SET? until you find the first day you want to adjust –...
Page 16
INTRODUCTION Cont... There are 3 models in the Lifestyle range: GRAM LP241Si – a 24hr program, with central heating and hot water T-SUN working independently for up to 3 heating periods each day, and .00am every day the same. .00am LP522Si –...
Page 17
flash a warning. ating peri- SWITCHING ON 1 – start of first timed period s in OFF 1 – end of first timed period ON 2 – start of second timed period OFF 2 – end of second timed period ON 3 –...
Page 18
Advance will only operate in TIMED or ONCE modes. OFF3 2. Press & Hold Boost to switch on for an extra hour ( & BST will be displayed), then Press again for two ( ) or three ( ) hours. To cancel Boost, Press Boost again ( ).
Page 19
THE LP241Si 24hr ELECTRONIC PROGRAMMER Cont... THE LP5 Changin The standard program Your system will come on for up to 3 heating periods every 24hrs. Press th ON1 starts the first one, OFF1 finishes it, and so on. Notice that on the standard program ON2 and OFF2 are set to the same time for both central heating and hot water.
Page 20
When y PROG? the disp Press YES and you’ll see ON1, the start of your first central heat- ing period. Adjust it in 1-minute steps using the – and + but- tons. If the – and + buttons are held down, the time changes in 10-minute steps.
Page 21
on each programmer will return to normal operation. working THE LP522Si 5/2-DAY ELECTRONIC PROGRAMMER If the tim will still LP522Si – a 5/2-day program allowing for different heating timings at the weekends, with central heating and hot water having d working independently for up to 3 heating periods each day.
Page 22
THE LP522Si 5/2-DAY ELECTRONIC PROGRAMMER Cont... THE LP7 Changing the timings Set all w 24hrs. Press the SET? button and you’ll see ‘SET PROG?’. First you that on weekda me for m won’t any furt hange ent, go PROG? Press th Set the weekday central heating PROG? GRAM...
Page 23
hanges in heating Press YES, then set your times in the same way. Remember, in this mode you can have different times to your central heating if you wish. Press Y Set weekend central heating central Remem ?, then When you press SET? after OFF3 for the weekday hot water, central the display will ask ‘SET CH SAT SUN PROG?’.
Page 24
automatically goes back to normal operation. ck to SERVIC The standard program ammer Your system will come on for up to 3 heating periods every Applica 24hrs. ON1 starts the first period, OFF1 finishes it, and so on. Notice that ON2 and OFF2 are set to the same time.* This If your i means your system won’t respond, but if you want to activate then yo...
Page 25
If you h MON TUE WED THU FRI PROG? contac Press YES and the display will ask ‘SET CH MON to FRI PROG?’. SETTIN entral heat- + but- Applica hanges in MON TUE WED THU FRI PROG? SETTIN Press YES, and you’ll see ON1, the start of your first central The clo heating period.
Page 26
you’ve finished, press SET? until you see ‘SET SAT SUN The we PROG?’. ntral the we G?’. Press t PROG? If you don’t want to alter any individual days, keep pressing SET? until you see ‘SET SAT SUN PROG?’. Set the Press Y SAT SUN water...
Page 27
7.00am 9.00am Press S then m 12.00pm m 12.00pm 4.00pm m 11.00pm then and then revert to the normal time display. The display will cycle continuously. When you see this it means; SERVICE DUE ON 25 DECEMBER. SERVICE INTERVAL FEATURE Cont... You should contact your service engineer to arrange a service.
Page 28
contact your service engineer immediately. SETTING THE CLOCK AND DATE Room T Applicable to all models. SETTING THE CLOCK ntral The clock in your programmer has been set at the factory, nd + and automatically accounts for British Summer Time. changes However, should you need to set the clock, read on.
Page 29
normal operation. If you do, go on to the next section. st day ering any When SETTING THE DATE The weekday is automatically calculated from the date, so if the weekday is incorrect you’ll need to reset the date. Refer to for wiri Overru Press the SET? button until you see SET DATE?.
Need help?
Do you have a question about the LP111Si and is the answer not in the manual?
Questions and answers