Mitsubishi Electric FX3UC-16MT/DSS Hardware Manual

Side
B
Side Side
A B
JAPANESE ENGLISH
FX (D, DS, DSS) SERIES
3UC
PROGRAMMABLE CONTROLLERS
HARDWARE MANUAL
Manual Number JY997D50501
Revision E
Date December 2017
This manual describes the part names, dimensions, mounting,
cabling and specifications for the product. This manual is extracted
from FX (D,DS,DSS) Series User's Manual - Hardware Edition.
3UC
Refer to FX Series User's Manual - Hardware Edition details.
3UC
Before use, read this manual and manuals of relevant products fully
to acquire proficiency in the handling and operating the product.
Make sure to learn all the product information, safety information,
and precautions.
And, store this manual in a safe place so that it can be taken out and
read whenever necessary. Always forward it to the end user.
Registration
The company name and the product name to be described in this
manual are the registered trademarks or trademarks of each
company.
Effective December 2017
Specifications are subject to change without notice.
© 2013 Mitsubishi Electric Corporation
Safety Precaution
(Read these precautions before use.)
If the equipment is used in a manner not specified by the manufacturer,
the protection provided by the equipment may be impaired.
This manual classifies the safety precautions into two categories:
and .
Indicates that incorrect handling may cause
hazardous conditions, resulting in death or
severe injury.
Indicates that incorrect handling may cause
hazardous conditions, resulting in medium or
slight personal injury or physical damage.
Depending on the circumstances, procedures indicated by
may also cause severe injury.
It is important to follow all precautions for personal safety.
STARTUP AND
MAINTENANCE
PRECAUTIONS
• Do not touch any terminal while the PLC's power is on.
Doing so may cause electric shock or malfunctions.
• Before cleaning or retightening terminals, cut off all phases of
the power supply externally.
Failure to do so may cause electric shock.
JY997D50501E
STARTUP AND
MAINTENANCE
PRECAUTIONS
• Before modifying or disrupting the program in operation or
running the PLC, carefully read through this manual and the
associated manuals and ensure the safety of the operation.
An operation error may damage the machinery or cause accidents.
• Do not change the program in the PLC from two or more
peripheral equipment devices at the same time. (i.e. from a
programming tool and a GOT)
Doing so may cause destruction or malfunction of the PLC program.
• Use the battery for memory backup correctly in FX
3UC
User's Manual - Hardware Edition.
- Use the battery only for the specified purpose.
- Connect the battery correctly.
- Do not charge, disassemble, heat, put in fire, short-circuit,
connect reversely, weld, swallow or burn the battery, or apply
excessive forces (vibration, impact, drop, etc.) to the battery.
- Do not store or use the battery at high temperatures or
expose to direct sunlight.
- Do not expose to water, bring near fire or touch liquid
leakage or other contents directly.
- Incorrect handling of the battery may cause heat excessive
generation, bursting, ignition, liquid leakage or deformation,
and lead to injury, fire or failures and malfunctions of facilities
and other equipment.
- When replacing the battery, make sure to use our specified
product (FX -32BL).
3U
- When a battery error occurs ("BAT" LED is lit in red), follow the
description in FX Series User's Manual - Hardware Edition.
3UC
STARTUP AND
MAINTENANCE
PRECAUTIONS
• Turn off the power to the PLC before attaching or detaching the
memory cassette. If the memory cassette is attached or
detached while the PLC's power is on, the data in the memory
may be destroyed, or the memory cassette may be damaged.
• Do not disassemble or modify the PLC.
Doing so may cause fire, equipment failures, or malfunctions.
For repair, contact your local Mitsubishi Electric representative.
• Turn off the power to the PLC before connecting or
disconnecting any extension cable.
Failure to do so may cause equipment failures or malfunctions.
• Turn off the power to the PLC before attaching or detaching the
following devices.
Failure to do so may cause equipment failures or malfunctions.
- Peripheral devices, extension units/blocks, connector
conversion adapter, extension power supply units, special
adapters, and FX Series terminal blocks.
- Battery and memory cassettes
• Do not use the chemicals for cleaning.
• If there is the possibility of touching the PLC inside a control
panel in maintenance, make sure to discharge to avoid the
influence of static electricity.
DISPOSAL
PRECAUTIONS
• Please contact a certified electronic waste disposal company for
the environmentally safe recycling and disposal of your device.
When disposing of batteries, separate them from other waste
according to local regulations.
(For details of the Battery Directive in EU countries, refer to
FX Series User's Manual - Hardware Edition.)
3UC
TRANSPORTATION
AND STORAGE
PRECAUTIONS
• Before transporting the PLC, turn on the power to the PLC to
check that the BAT LED is off, and check the battery life.
If the PLC is transported with the BAT LED on or the battery
exhausted, the battery-backed data may be unstable during
transportation.
TRANSPORTATION
AND STORAGE
PRECAUTIONS
• The PLC is a precision instrument. During transportation, avoid
impacts larger than those specified in Section 2.1 by using
dedicated packaging boxes and shock-absorbing palettes.
Failure to do so may cause failures in the PLC.
After transportation, verify operation of the PLC and check for
damage of the mounting part, etc.
• When transporting lithium batteries,
transportation regulations.
(For details of the regulated products, refer to FX
Series
User's Manual - Hardware Edition.)
Associated manuals
How to obtain manuals
For the necessary product manuals or documents, consult with
your local Mitsubishi Electric representative.
Associated manuals
FX (D, DS, DSS) Series PLC (main unit) comes with this
3UC
document (hardware manual).
For a detailed explanation of the FX 3UC
information on instructions for PLC programming and special
extension unit/block, refer to the relevant documents.
Manual name Manual No.
FX Series JY997D28701
3UC
User's Manual MODEL CODE:
- Hardware Edition 09R519
FX 3S /FX 3G /FX 3GC /
FX /FX Series JY997D16601
3U 3UC
Programming Manual MODEL CODE:
- Basic & Applied 09R517
Instruction Edition
MELSEC-Q/L/F
SH-080782
Structured
MODEL CODE:
Programming Manual
13JW06
(Fundamentals)
FXCPU Structured JY997D26001
Programming Manual MODEL CODE:
[Device & Common] 09R925
FXCPU Structured
JY997D34701
Programming Manual
MODEL CODE:
[Basic & Applied
09R926
Instruction]
FXCPU Structured
JY997D34801
Programming Manual
MODEL CODE:
[Application
09R927
Functions]
FX Series User's
JY997D16901
Manual - Data
MODEL CODE:
Communication
09R715
Edition
FX /FX /FX /
3S 3G 3GC
FX /FX Series JY997D16701
3U 3UC
User's Manual MODEL CODE:
- Analog Control 09R619
Edition
FX /FX /FX /
3S 3G 3GC
FX /FX Series JY997D16801
3U 3UC
User's Manual MODEL CODE:
- Positioning Control 09R620
Edition
Certification of UL, cUL standards
FX series main units, FX
3UC
power supply unit and FX
blocks supporting UL, cUL standards are as follows:
UL, cUL file number: E95239
Models: MELSEC FX
FX -MT/D
3UC
follow required
Where  indicates: 16, 32, 64, 96
Series
3UC FX -16MR/D-T
3UC
FX -232ADP(-MB)
3U
FX -CF-ADP
3U
FX -4AD-ADP
3U
FX -3A-ADP
3U
FX -4AD-PTW-ADP FX
3U
FX -4AD-TC-ADP
3U
FX -1PS-5V
3UC
Models: MELSEC FX
FX -16EX(-DS)
2NC
FX -16EYT(-DSS) FX
2NC
FX -16EX-T(-DS)
2NC
Series hardware and
Models: MELSEC FX
FX -8ER-ES/UL
2N
FX -8EYR-ES/UL
2N
Description FX -8EYT-ESS/UL
2N
FX -16EX-ES/UL
2N
Explains FX Series
3UC
PLC specification details FX -16EYT-ESS/UL FX
2N
for I/O, wiring, installation,
and maintenance.
Compliance with EC directive (CE Marking)
Describes PLC
programming for basic/
This product complies with EC directive, however, this document
applied instructions STL/
does not guarantee that a mechanical system including this product
SFC programming and
will comply with EC directive.
devices.
Compliance to EMC directive and LVD directive of the entire
Programming methods,
mechanical system should be checked by the user / manufacturer.
specifications, functions,
For more details please contact the local Mitsubishi Electric sales
etc. required to create
site.
structured programs.
Caution for Compliance with EC directive
Devices, parameters, etc.
provided in structured
• Please use the FX
3UC
projects of GX Works2.
controllers while installed in conductive shielded control panels
under a general industrial environment.
Sequence instructions
• Programmable controllers are open-type devices that must be
provided in structured
installed and used within conductive control panels. Please secure
projects of GX Works2.
the control panel lid to the control panel (for conduction). Installation
within a control panel greatly affects the safety of the system and
Application functions
aids in shielding noise from the programmable controller.
provided in structured
• For the control panel, use the product having sufficient strength, fire
projects of GX Works2.
protectiveness and shielding property to an installation environment.
• 24 V DC of the power supply must be supplied from the circuit
Explains N:N link, parallel
double/reinforced insulated from the main power supply (MAINS).
link, computer link, no
protocol communication Caution for compliance with the LVD directive
by RS instructions/FX -
2N (EN61010-2-201:2013) (*1)
232IF.
• To an external connection port other than AC power supply terminal
and AC input/output terminal, connect the circuit separated from a
Describes specifications
dangerous voltage by a double/reinforced insulation.
for analog control and
programming methods for • Between the commons having the adjacent relay output
FX /FX /FX /FX /
3S 3G 3GC 3U terminals, if an external power supply is higher than 120 V AC,
FX Series PLC. the insulation is basic. Therefore, when using 120 V AC or higher
3UC
external power supply and 30 V DC/AC or lower external power
Explains the specifications
supply between the adjacent commons, do not handle 30 V DC/
for positioning control of
AC or lower external power supply as a touchable part, (When
FX /FX /FX /FX /
3S 3G 3GC 3U
handling 30 V DC/AC or lower external power supply as a
FX Series and
3UC
touchable part, add a basic insulation.)
programming procedures
series special adapter, extension
3U
/FX series input/output extension
2N 2NC
series manufactured
3U(C)
FX -MT/DSS
3UC
FX -16MR/DS-T
3UC
FX -485ADP(-MB)
3U
FX -ENET-ADP
3U
FX -4DA-ADP
3U
FX -4AD-PT-ADP
3U
-4AD-PNK-ADP
3U
series manufactured
2NC
FX -32EX(-DS)
2NC
-32EYT(-DSS)
2NC
FX -16EYR-T(-DS)
2NC
series manufactured
2N
FX -8EX-ES/UL
2N
FX -8EYR-S-ES/UL
2N
FX -8EX-UA1/UL
2N
FX -16EYR-ES/UL
2N
-16EYS
2N
(D, DS, DSS) Series programmable