Subscribe to Our Youtube Channel
Summary of Contents for Shoe Systems Plus SUPREME MGP34
- Page 1 SUPREME MGP34 BENCH SANDER Operator Manual Shoe Systems Plus, Inc. 249 W Main St. Goshen, NY 10924 www.shoesystemsplus.com 800-354-6278...
- Page 2 MGP34 Operator Manual SUPREME MGP34 BENCH SANDER INTRODUCTION The Supreme Bench Sander is a compact, durable machine designed for fast, complete finishing work. It will deliver efficient, dependable service when used correctly and with care. As with any piece of specialized equipment, for best performance the manufacturer’s instructions must be followed.
- Page 3 MGP34 Operator Manual TOOL SHOULD BE MAINTAINED • Always unplug tool prior to inspection. • Consult manual specific maintaining adjusting procedures. • Keep tool clean for safest operation. • Remove adjusting tools. Form habit of checking to see that adjusting tools are removed before turning machine on. •...
-
Page 4: Operating The Supreme Bench Sander
MGP34 Operator Manual DESCRIPTION Supreme Bench Grinders are equipped with a totally enclosed ball bearing motor. Armature assembly is dynamically balanced for smooth operation. Motor housing is compact so long pieces of work can press against wheels without touching the motor frame. Removable wheel guards allow for easy changing of wheels. -
Page 5: Installation
MGP34 Operator Manual INSTALLATION The Supreme Bench Sander should be located on a flat, firm surface, in an area free of obstructions that could interfere with the safe operation of the equipment. The Bench Sander should be positioned and leveled on a solid bench or stand to obtain quiet operation with a minimum of vibration. - Page 6 MGP34 Operator Manual • This grinder is equipped with an approved 3-conductor cord rated at 300V and a 3-prong, grounding type plug (See Figure 1) for your protection against shock hazards. Figure 1. 3-Prong Receptacle • Grounding plug should be plugged directly into a properly installed and grounded 3-prong grounding-type receptacle (See Figure 1).
-
Page 7: Extension Cords
MGP34 Operator Manual • A temporary 3-prong to 2-prong grounding adapter (See Figure 2) is available for connecting plugs to a two pole outlet if it is properly grounded. Figure 2. 2-Prong Receptacle • Do not use a 3-prong to 2-prong grounding adapter unless permitted by local and national codes and ordinances. -
Page 8: Electrical Connections
MGP34 Operator Manual ELECTRICAL CONNECTIONS WARNING: All electrical connections must be performed by a qualified electrician. Make sure tool is off and disconnected from power source while motor is mounted, connected, reconnected or anytime wiring is inspected. WARNING: If the electrical cord, plug or wiring should become frayed or damaged, replace it at once. -
Page 9: Sanding Belt Replacement
MGP34 Operator Manual START-UP WARNING: Eye protection should always be worn by the operator and others in the work area when setting up the machine. Eye protection is required for protection from flying debris and dust, which could cause eye injury. Before shipment, your Supreme Sander was checked at the factory for proper adjustment and operation. - Page 10 MGP34 Operator Manual To replace the belt: Take off the bayoneted sanding wheel from the motor shaft. Unscrew the nut at the end of the rubber wheel to release pressure. You do not need to take it off. Only unscrew the nut. Slide the sanding belt out of the rubber wheel.
- Page 11 MGP34 Operator Manual ACCESSORIES WARNING: Eye protection should always be worn by the operator and others in the work area when using the accessories supplied with the Supreme Sander. Eye protection is required for protection from flying debris and dust, which could cause eye injury.
- Page 12 MGP34 Operator Manual Supreme Bench Sander...
-
Page 13: Maintenance
MGP34 Operator Manual MAINTENANCE A properly maintained machine will give you years of satisfactory service, whereas an abused machine will not. We strongly recommend that you observe the following procedures for your own benefit and safety. WARNING: Eye protection should always be worn by the operator and others in the work area when servicing the machine. -
Page 14: Monthly Maintenance
MGP34 Operator Manual MONTHLY MAINTENANCE Take off the hose from the blower housing and look at the fan to see if there are small particles stuck to the fan. N.B. Those small particles can create vibrations of the bench sander. Clean your dust bag with a shop vac or a vacuum cleaner. -
Page 15: Troubleshooting
MGP34 Operator Manual TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION Grinder won’t start 1. Blown line fuse or tripped circuit 1. If fuse is blown, replace with fuse breaker of proper size. If breaker tripped, reset it. 2. Low line voltage 2. - Page 16 MGP34 Operator Manual LOST OF SUCTION IN DUST COLLECTION Dust bag may be full. Empty it. Blower fan may be clogged. Clean it. Take apart the side cover of the blower housing to have access to the fan. MOTOR STOPS WITH SWITCH ON CAUTION: Turn switch off immediately.
- Page 17 MGP34 Operator Manual ACCESSORIES FOR BENCH SANDER PARTS # ESCRIPTION SMAK060 LACK HANDLE TO ADJUST DUST PORT SUPPORT HAFT BUSHING WITH SLOT INCLUDED STEEL BALL SPRING AND SCREWS 31786BAYONET M ALE BAYONET FOR RUBBER WHEEL FOR RIGHT SIDE 09130019 AN FOR DUST COLLECTING SYSTEM 31786 4’’...
- Page 18 MGP34 Operator Manual Supreme Bench Sander...
Need help?
Do you have a question about the SUPREME MGP34 and is the answer not in the manual?
Questions and answers