Advertisement
Quick Links
Thank you for purchasing the Venturi EVO FPV wing
The Venturi FPV is designed for First Person Viewing (FPV) and for UAV/Drone
experimentation.
There is a power system for this model, see the website for details.
As well as this power system you will require:
2 x Standard size servos 43g (standard size)
1 x Long range receiver
1 x Lipo battery(s) (2x 3300mah 3S or 4S 11.1v)
1 x connectors set
1 x Transmitter capable of elevon mixing or mixing module
1 x Lipo compatible charger
See website for power system details
HOT GLUE GUN
UHU POR
CA GLUE
PVA WOOD GLUE
CRITICAL DATA
CENTRE OF GRAVITY 185 +/-10mm
BACK FROM THE FOAM WING LEADING
EDGE AT ROOT
TARGET FLYING WEIGHT
2000 grams without FPV gear & camera
with 2 x 3300mah 4S batteries
Advertisement
Summary of Contents for flyingwings Venturi EVO 2 FPV
- Page 1 Thank you for purchasing the Venturi EVO FPV wing The Venturi FPV is designed for First Person Viewing (FPV) and for UAV/Drone experimentation. There is a power system for this model, see the website for details. As well as this power system you will require: 2 x Standard size servos 43g (standard size) 1 x Long range receiver 1 x Lipo battery(s) (2x 3300mah 3S or 4S 11.1v)
-
Page 2: Fuselage Assembly
STEP Fuselage assembly Carefully cut the tabs holding the parts on to the sheets of ply. Sand off the remaining tab and lightly bevel off the interlocking part of the piece, to help in assembly. STEP Glue the 2 motor plates together using wood glue or UHU por, be careful to align them accurately, allow to dry Tabs Sand the tabs down as shown... - Page 3 Once you have trimmed and sanded the ply parts, its ready for assembly. Lay the fuselage side on a flat surface and assemble without glue. Once you have trimmed and sanded the ply parts, its ready for assembly. Lay the fuselage side on a flat surface and assemble without glue.
- Page 4 degrees IMPORTANT: check that the fuselage sides are aligned here before using glue You can use thin CA glue to hold the assembly together step by step. Soak the CA glue into the tab joints, use a weight to hold it in position. When you are happy that the fuselage is correct and aligned, run a bead of wood glue or UHU por around all the...
- Page 5 Wing Preparation Guide lines All FPV installations are different, but we offer some guide lines for the Venturi EVO 2 Video TX There are some pre-cut slots in the fuselage to run cables from the wing to the autopilot /osd etc Using the spar holes, hold the fuselage against the wing and mark on the wing where these slots line up.
- Page 6 Attaching wings to fuselage IMPORTANT ! The tube spars are a tight fit in the wings, to help assembly, use insert the spars into the wings with twisting action making them easier to insert when you come to assemble the wings. Mark each spar at the centre point Slide the two carbon tube spars through the fuselage, short on at the front.
- Page 7 Elevon Preparation Using a sanding block, chamfer the leading edge of the Balsa elevons. Remember they are handed left & Right, Cover using just coloured tape/ L e a d i n g E d g e Using 25mm strapping tape or cutting 50mm tape down the centre, attach the elevons.
- Page 8 Foam Parts Rear Hatch Plate Front Hatch Plate optional Rear Cover Hatch Upper Nose Lower Fuselage The foam parts installation is best in this sequence 1. Install motor mount & battery velcro straps 2. Glue in lower fuselage 3. Install all of your equipment, like the AP, ESC’s Motor etc 4.
- Page 9 Outboard style: quieter, Motor Mounting may need more nose weight to balance (CofG)wing Note: Upthrust, this Inboard Style: Noisier, is correct easier to get balance (CofG) Wingtips: Cut some stapping tape, and wrap it around the front section of the wingtip, top and bottom.
- Page 10 Help ! call 01908 615163 sales@flyingwings.co.uk...