Switches And Controls - Luxman R-1070 Owner's Manual

SWITCHES
&
CONTROLS
1.
FM
lF
Bandwidth Selector Switch
This switch is provided
to
realize
either
the
low
distortion
characteristic which
aims
to
improve sonic
quality, or the
high
selectivity
characteristic
which aims
to
ensure
clear
reception.
The switch is
of
an
alternate push-on,
push-off type.
ln
the
"protruded"
position,
the lF
bandwidth
is "WlDE",
and the
selectivity at
t400kHz
becomes
30dB
to
realize low distortjon.
When
it
is depressed,
the bandwidth
is
"NARROW" to
provide
90dB
selectivity
at
1400kH2,
which is
effective
to
eliminate
disturbance by
an
adjacent
station.
2. FM MUTING
SWITCH
Annoying interstation
noise
which
is
possible when the exact
tuning
point
is not obtained
can be
eliminated by this switch
in
the
case
of
FM reception.
Keep
this switch
unpressed
to
remove
interstation
noises
or
other impracticably
weak signals.
Such
FM
signals as
can be
received
in
the'lnormal" position
can
be
practised
for
stereo FM reception.
lt
is recommended
to
set
this
switch
always
in the "protruded"
position except
when weak
signals are received.
3.
TAPE MONITOR
SWITCH
When
this switch is
pressed
in, tape playback
is
possible
either from
the
DECK-1 Monitor terminal
or
DECK-2/TAPE
CONNECTOR.
ln
the
case
of
3-head tape-recorder which
has
a
playback
head simultaneous
playback monitoring
is
possible while
recording.
ln
this
case
this
receiver
receives
playback
signals
from
either
of
DECK-1
or
DECK-2 Monitor
Terminals
or
Tape Connector
while
feeding recording
signals
to
DECK-1, DECK-2
Rec.
Out Terminals
or
Tape Connector. For
tape playback
the
Tape Selector
Switch
(4)
has
to
be set
at
the
corresponding pgsition to
which the tape
recorder
is
connected.
Caution: Only
tape playback is
possible
if
this switch
is pressed
in,
and therefore except
for
tape
playback this switch
should
be
kept
released,
i.e.,
unpressed.
4.
TAPE SELECTOR
SWITCH
This
allows
to
select tape
playback
terminals. When this
is
kept
unpressed at the
protruded position tape playback
is feasible
from the DECK-l Monitor
Terminal,
while
when
pressed in,
the
DECK-2
Monitor Terminal
and Tape Connector are simul-
taneously
put into
function.
As these
2
are coupled inside
and
affect
each
other,
connection
of 2
tape
recorders
to
DECK-2
Monitor Terminal
and Tape Connector
should be
avoided
for
normal playback.
5.
TAPE DUBBING
SWITCH
The dubbing switch
is
provided with
3
positions;
at the center
"source"
position such program source as is
selected
by
the
lnput
Selector
Switch
is available
for playback.
When set
at the "dub 1 Io
2"
position the output of
tape
recorder
i
is
fed to the input
of
tape
recorder
2 for
dubbing
(reprint) , while the "dub 2 to 1" position
offers tape
dubbing
from "DECK-2" Io "DECK-1".
As
this
Dubbing Switch
is
inde-
pendent
of
the
signal
path
you
can
enjoy playback
of
other
program
sources even during
tape
dubbing.