Download
Share
Print this page
Envirovent energiSava 210 Instruction Leaflet
  1. Manuals
  2. Brands
  3. Envirovent Manuals
  4. Test Equipment
  5. energiSava 210
  6. Instruction leaflet
Envirovent energiSava 210 Instruction Leaflet

Envirovent energiSava 210 Instruction Leaflet

Whole house heat recovery system
Hide thumbs

Advertisement

Quick Links

Download this manual
energiSava 210
Instruction leaflet

Advertisement

loading
Need help?

Need help?

Do you have a question about the energiSava 210 and is the answer not in the manual?

Questions and answers

Summary of Contents for Envirovent energiSava 210

  • Page 1 210 Instruction leaflet...
  • Page 2 General information Technical information Installation Characteristics and electrical connections Commissioning the energiSava 210 6. Operating the energiSava 210 The following items are included : 1. 1 x energiSava 210 2. 1 x remote control 3. 1 x wall bracket 4. 2 x drain ducts 5.
  • Page 3 1. GENERAL INFORMATION 1.1 - Introduction This manual is intended for the use of the central balanced-flow high efficiency energiSava 210 and its peripherals (ductwork, vents, controllers). It is designed to provide clear and safe guidance for the design, installation and use of the product.

  • Page 4: Technical Information

    2. TECHNICAL INFORMATION 2.1.- General information The energiSava 210 ensures optimum ventilation of a house with a maximum energy recovery. It draws air from the rooms (bathroom(s), toilet, kitchen and wash room(s)) and supplies fresh air through the main rooms (living room, bedroom (s), office, etc ).
  • Page 5 New fresh air inlet: This spigot is to connect the supply duct of fresh air from outside. Install the fresh air intake (wall or roof) a sufficient distance from any area of high pollution (trees, exhaust fumes, road, etc). This duct must be sealed and insulated to prevent condensation on the outside and inside.
  • Page 6 2.3.- Dimensional characteristics 2.3.a - Central: Weight: 15Kg: 2.3.b - Remote control:...
  • Page 7 Wall bracket It is advisable to install the energiSava 210 in the heated area of the house. If not, it is essential to isolate the condensation drain. In areas where temperatures are regularly negative or can drop below -10ºC, it is...
  • Page 8 • Heating housing In summer, in this configuration, the condensation is generated on the other side of the heat exchanger. So, the energiSava 210 is equipped with a dual condensate drain system. • Installing and connecting the drain kit for heated housing...
  • Page 9 SAMPLE ” DISTRIBUTION” ASSEMBLY kitchen BDO or BOAP CPR or CT PLENUM UNI EX 5P/125 Toilets BDO or TPM 80 RD 80 Air intake PAQS125 PLENUM UNI 6P/125 RD 80* Air intake PAF 125 BDO or TPM 80 Living room &...
  • Page 10 SAMPLE “DISTRIBUTION” ASSEMBLY Kitchen CPR or CT BDO or BOAP Bathrooms BDO or TPM 80 + RD80 Air intake PAQS125 BDO 80 Air intake PAF 125 RD80* Living Room & (*):Bedrooms If using insulated flexible duct, it is imperative to fully stretch it.
  • Page 11 4 - CHARACTERISTICS AND ELECTRICAL CONNECTIONS Connect the supplied cable to the mains using a sealed connection box. Power: Single phase 230V-50Hz Max. current: 0,8 A Max.Power: 80 W Maximum ambient temperature: 50ºC Maximum flow temperature: 45ºC Connection Electrical panel Control wire type H05VV-F-4G0,25 Connection box...
  • Page 12 Pin 8 = Terminal 0 MODBUS (*) Connector Regulation extract motor Regulation supply motor Not functional on this version By-Pass Humidity sensor On/Off contact (*) Power supply Power supply energiSava 210 motor motor power supply Extract fan Supply fan *: Not supplied...
  • Page 13 5- COMMISSIONING OF THE energiSava 210 5.1.- For installation: The remote control allows: • Adjust the airflows (Minimum, kitchen boost and by-pass airflow (night cooling) • Adjust the timing of a dirty filters (6, 9, 12 or 15 months) (factory setting 9 months) •...
  • Page 14 5.1.b - Timing dirty filters alarm It is possible to set the timing to 6, 9, 12 or 15 months (9 months factory setting). Fouling is linked to the external environment (pollution, pollen,..) and the use of housing (dust, cooking fats..). It is advisable to modify this parameter after the second alarm.
  • Page 15 There are two possibilities: a. Create an air inlet specific to the chimney. b. add an additional supply airflow to the calculated energiSava 210 airflow to facilitate the natural draught of the chimney. Follow the recommendations below: •...
  • Page 16 Holiday mode Filters reset Kitchen Boost Minimum airflow (green LED): When the energiSava 210 is in Boost mode, it is possible, by pressing the left button, to return to the minimum airflow before ½ hour has elapsed Boost kitchen (green LED): A button that enables the boost airflow for the kitchen to be selected in ½-hour steps.
  • Page 17 Check that the unused spigots on plenums are sealed (if installed) • Condensation drain well connected (siphon) • Check that all connections are sealed (on the energiSava 210, on plenums and vents) • Check the setting of the power circuit breaker 2. Turn on the energiSava 210...
  • Page 18 EnviroVent Ltd Envirovent House Hornbeam Business Park Harrogate Hg2 8PA 01423 810 810 info@envirovent.com www.envirovent.comm REF. 99999999...